Using hda after an "hdparm -d1 /dev/hda" give :
home kernel: hda: timeout waiting for DMA
home kernel: hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
home kernel: hda: DMA disabled
home kernel: ide0: reset: success
Follow some debug infos:
with my old good PIIX4 mobo:
----------------------------
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 84320D4, ATA DISK drive
hdc: WDC AC24300L, ATA DISK drive
hdd: ASUS CD-S340, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 84320D4, 4028MB w/256kB Cache, CHS=1023/128/63, UDMA
hdc: WDC AC24300L, 4112MB w/256kB Cache, CHS=8912/15/63, UDMA
hdd: ATAPI 34X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.55
With my current alim1533 mobo:
------------------------------
Uniform Multi-Platform E-IDE driver Revision: 6.20
ALI15X3: IDE controller on PCI bus 00 dev 78
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 84320D4, ATA DISK drive
ide: Assuming 40MHz system bus speed for PIO modes; override with idebus=xx
hdc: WDC AC24300L, ATA DISK drive
hdd: ASUS CD-S340, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 84320D4, 4028MB w/256kB Cache, CHS=1023/128/63
hdc: WDC AC24300L, 4112MB w/256kB Cache, CHS=8912/15/63
hdd: ATAPI 34X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.05
#cat /proc/ide/ali
Ali M15x3 Chipset.
------------------
PCI Clock: 33.
CD_ROM FIFO:No , CD_ROM DMA:No
FIFO Status: contains 0 Words, runs.
-------------------primary channel-------------------secondary channel---------
channel status: On On
both channels togth: Yes Yes
Channel state: OK DRQ
Add. Setup Timing: 1T 1T
Command Act. Count: 3T 3T
Command Rec. Count: 3T 3T
----------------drive0-----------drive1------------drive0-----------drive1------
DMA enabled: Yes No Yes Yes
FIFO threshold: 8 Words 8 Words 8 Words 8 Words
FIFO mode: FIFO On FIFO On FIFO On FIFO Off
Dt RW act. Cnt 3T 8T 3T 3T
Dt RW rec. Cnt 1T 16T 1T 1T
-----------------------------------UDMA Timings--------------------------------
UDMA: OK No OK OK
UDMA timings: 2.5T 1.5T 2.5T 2.5T
-- More info on request thanks in advance, luca------------------------------------------------------------------ E-mail......: Luca Montecchiani <m.luca@iname.com> W.W.W.......: http://i.am/m.luca - http://luca.myip.org Speakfreely.: sflwl -hlwl.fourmilab.ch luca@ I.C.Q.......: 17655604 -----------------------=(Linux since 1995)=-----------------------
Non esiste vento favorevole per il marinaio che non sa dove andare Seneca
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/