Re: [PATCH v11 4/4] arm64: dts: qcom: Add base HAMOA-IOT-EVK board

[Yingying Tang]

On 9/16/2025 6:36 PM, Konrad Dybcio wrote:
> On 9/16/25 12:29 PM, Yingying Tang wrote:
>>
>>
>> On 9/16/2025 6:14 PM, Dmitry Baryshkov wrote:
>>> On Tue, Sep 16, 2025 at 09:42:26AM +0800, Yingying Tang wrote:
>>>>
>>>>
>>>> On 9/12/2025 5:00 PM, Stephan Gerhold wrote:
>>>>> On Wed, Sep 10, 2025 at 05:02:12PM +0800, Yijie Yang wrote:
>>>>>> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of
>>>>>> the Hamoa IoT SoM and a carrier board. Together, they form a complete
>>>>>> embedded system capable of booting to UART.
>>>>>>
>>>>>> Make the following peripherals on the carrier board enabled:
>>>>>> - UART
>>>>>> - On-board regulators
>>>>>> - USB Type-C mux
>>>>>> - Pinctrl
>>>>>> - Embedded USB (EUSB) repeaters
>>>>>> - NVMe
>>>>>> - pmic-glink
>>>>>> - USB DisplayPorts
>>>>>> - Bluetooth
>>>>>> - WLAN
>>>>>> - Audio
>>>>>>
>>>>>> Written in collaboration with Quill Qi (Audio) <le.qi@xxxxxxxxxxxxxxxx>,
>>>>>> Jie Zhang (Graphics) <quic_jiezh@xxxxxxxxxxx>, Shuai Zhang (Bluetooth)
>>>>>> <quic_shuaz@xxxxxxxxxxx>, Yingying Tang (WLAN) <quic_yintang@xxxxxxxxxxx>,
>>>>>> and Yongxing Mou (USB DisplayPorts) <quic_yongmou@xxxxxxxxxxx>.
>>>>>
>>>>> This looks like you should have Co-developed-by: tags together with
>>>>> their Signed-off-by: tags.
>>>>>
>>>>>>
>>>>>> Signed-off-by: Yijie Yang <yijie.yang@xxxxxxxxxxxxxxxx>
>>>>>> ---
>>>>>>  arch/arm64/boot/dts/qcom/Makefile          |    1 +
>>>>>>  arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1221 ++++++++++++++++++++++++++++
>>>>>>  2 files changed, 1222 insertions(+)
>>>>>>
>>>>>> +
>>>>>> +	vreg_wcn_3p3: regulator-wcn-3p3 {
>>>>>> +		compatible = "regulator-fixed";
>>>>>> +
>>>>>> +		regulator-name = "VREG_WCN_3P3";
>>>>>> +		regulator-min-microvolt = <3300000>;
>>>>>> +		regulator-max-microvolt = <3300000>;
>>>>>> +
>>>>>> +		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
>>>>>> +		enable-active-high;
>>>>>> +
>>>>>> +		pinctrl-0 = <&wcn_sw_en>;
>>>>>> +		pinctrl-names = "default";
>>>>>> +
>>>>>
>>>>> regulator-boot-on?
>>>>
>>>> It shoulde be regulator-always-on
>>>
>>> Why it's not boot-on and always-on?
>>>
>> As I described before, connectivity power is voted by UEFI in boot phase.So PCIe link between connetivity card and RC4 is established once RC4 is on.
>> If we set this node as "regulator-boot-on", connectivity power will be down first then up. That cause PCIe link down and the link can't be trained again unless you reboot board.
>> So we can't set it to "regulator-boot-on"
> 
> Surely gpio-regulator.c implements .get_voltage which reads the pin
> state though? Did you test this, or are you theorycrafting?
> 
Yes we tested this case many times, "regulator-boot-on" causes PCIe link down. No any issue with "regulator-always-on"
> Konrad
>