Re: [PATCH 1/3] dt-bindings: interconnect: qcom,qcs615-rpmh: add clocks property to enable QoS

[Odelu Kukatla]

On 2/6/2026 12:21 PM, Dmitry Baryshkov wrote:
> On Fri, Feb 06, 2026 at 10:28:15AM +0530, Odelu Kukatla wrote:
>>
>>
>> On 2/5/2026 3:59 PM, Dmitry Baryshkov wrote:
>>> On Thu, Feb 05, 2026 at 03:10:31PM +0530, Odelu Kukatla wrote:
>>>>
>>>>
>>>> On 2/5/2026 2:31 PM, Konrad Dybcio wrote:
>>>>> On 2/5/26 7:06 AM, Odelu Kukatla wrote:
>>>>>>
>>>>>>
>>>>>> On 2/2/2026 4:33 PM, Konrad Dybcio wrote:
>>>>>>> On 2/2/26 8:05 AM, Odelu Kukatla wrote:
>>>>>>>> Aggre1-noc interconnect node on QCS615 has QoS registers located
>>>>>>>> inside a block whose interface is clock-gated. For that node,
>>>>>>>> driver must enable the corresponding clock(s) before accessing
>>>>>>>> the registers. Add the 'clocks' property so the driver can obtain
>>>>>>>> and enable the required clock(s).
>>>>>>>>
>>>>>>>> Only interconnects that have clock‑gated QoS register interface
>>>>>>>> use this property; it is not applicable to all interconnect nodes.
>>>>>>>>
>>>>>>>> Signed-off-by: Odelu Kukatla <odelu.kukatla@xxxxxxxxxxxxxxxx>
>>>>>>>> ---
>>>>>
>>>>> [...]
>>>>>
>>>>>>>> +  - if:
>>>>>>>> +      properties:
>>>>>>>> +        compatible:
>>>>>>>> +          contains:
>>>>>>>> +            enum:
>>>>>>>> +              - qcom,qcs615-aggre1-noc
>>>>>>>> +    then:
>>>>>>>> +      properties:
>>>>>>>> +        clocks:
>>>>>>>> +          items:
>>>>>>>> +            - description: aggre UFS PHY AXI clock
>>>>>>>> +            - description: aggre USB2 SEC AXI clock
>>>>>>>> +            - description: aggre USB3 PRIM AXI clock
>>>>>>>
>>>>>>> Should we also include the IPA clock here?
>>>>>>>
>>>>>>
>>>>>> Thanks for the review!
>>>>>>
>>>>>> For QCS615, the IPA clock is already enabled by the bootloader (xBL) and
>>>>>> kept on during the boot‑up stage. Because of this, we do not need to
>>>>>> explicitly enable the IPA clock in the interconnect driver when
>>>>>> accessing the QoS registers.
>>>>>
>>>>> Would we need to re-enable it to re-program the hardware if say the
>>>>> icc module is loaded after unused clk cleanup or after a cx collapse?
>>>>>
>>>>
>>>> IPA clock is not managed by GCC clock controller driver, so
>>>> clk_disable_unused does not disable it.
>>>
>>> The clk_disable_unused is not limited to the GCC. The clock is managed
>>> by the clk-rpmh, so clk_disable_unused applies to it too. 
>>>
>>
>> clk_disable_unused()/clk_disable_unused_subtree() does not disable RPMh
>> managed clocks, so it does not apply to IPA clock.
> 
> You are describing the current behaviour of one OS. The DTS should be
> describing the hardware. Other platforms describe IPA clock used by the
> aggre NoC nodes.
> 

I will update the bindings and the device tree to include the IPA clock
for the Aggre1 NoC node to ensure the driver handles it correctly,
aligning with other platforms. I will send out V2 with these changes.

Thanks,
Odelu
>>
>>>> As a result, the icc provider
>>>> does not need to re enable an IPA clock for QoS access after unused clk
>>>> cleanup. And QCS615 does *not* support Cx collapse.
>>>
>>> Does lack of CX collapse apply to SM6150?
>>>
>>
>> SM6150, QCS615, and Talos are all names referring to the same underlying
>> SoC family.
> 
> Ack, I was making sure that lack of CX collapse isn't related to IoT vs
> mobile case.
>