[PATCH RFT v3 3/3] arm64: dts: qcom: glymur-crd: Enable USB support
From: Abel Vesa
Date: Mon Mar 02 2026 - 12:17:07 EST
From: Wesley Cheng <wesley.cheng@xxxxxxxxxxxxxxxx>
The Qualcomm Glymur Compute Reference Device comes with 3 Type-C ports,
one USB Type-A, and a fingerprint reader connected over USB. Each of these
3 Type-C ports are connected to one of the USB combo PHYs and one of the
M31 eUSB2 PHYs. The Type-A is connected to the USB Multi-port controller
via one of the M31 eUSB2 PHYs and one USB3 UNI PHY. The fingerprint reader
is connected to the USB_2 controller. All M31 eUSB2 PHYs have associated
eUSB2 to USB 2.0 repeaters, which are either part of SMB2370 PMICs or
dedicated NXP PTN3222.
So enable all needed controllers, PHYs and repeaters, while describing
their supplies. Also describe the PMIC glink graph for Type-C connectors.
Signed-off-by: Wesley Cheng <wesley.cheng@xxxxxxxxxxxxxxxx>
Co-developed-by: Abel Vesa <abel.vesa@xxxxxxxxxxxxxxxx>
Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/glymur-crd.dts | 271 ++++++++++++++++++++++++++++++++
1 file changed, 271 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dts b/arch/arm64/boot/dts/qcom/glymur-crd.dts
index 877945319012..795ab0df3b40 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dts
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dts
@@ -60,6 +60,96 @@ key-volume-up {
};
};
+ pmic-glink {
+ compatible = "qcom,glymur-pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_0_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_0_qmpphy_out>;
+ };
+ };
+ };
+ };
+
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in1: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in1: endpoint {
+ remote-endpoint = <&usb_1_qmpphy_out>;
+ };
+ };
+ };
+ };
+
+ connector@2 {
+ compatible = "usb-c-connector";
+ reg = <2>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in2: endpoint {
+ remote-endpoint = <&usb_2_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in2: endpoint {
+ remote-endpoint = <&usb_2_qmpphy_out>;
+ };
+ };
+ };
+ };
+ };
+
vreg_nvme: regulator-nvme {
compatible = "regulator-fixed";
@@ -367,6 +457,36 @@ vreg_l4h_e0_1p2: ldo4 {
};
};
+&i2c5 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ ptn3222_0: redriver@43 {
+ compatible = "nxp,ptn3222";
+ reg = <0x43>;
+
+ reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+
+ vdd3v3-supply = <&vreg_l8b_e0_1p50>;
+ vdd1v8-supply = <&vreg_l15b_e0_1p8>;
+
+ #phy-cells = <0>;
+ };
+
+ ptn3222_2: redriver@47 {
+ compatible = "nxp,ptn3222";
+ reg = <0x47>;
+
+ reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+
+ vdd3v3-supply = <&vreg_l8b_e0_1p50>;
+ vdd1v8-supply = <&vreg_l15b_e0_1p8>;
+
+ #phy-cells = <0>;
+ };
+};
+
&pcie3b {
vddpe-3v3-supply = <&vreg_nvmesec>;
@@ -485,6 +605,21 @@ &pon_resin {
status = "okay";
};
+&smb2370_j_e2_eusb2_repeater {
+ vdd18-supply = <&vreg_l15b_e0_1p8>;
+ vdd3-supply = <&vreg_l7b_e0_2p79>;
+};
+
+&smb2370_k_e2_eusb2_repeater {
+ vdd18-supply = <&vreg_l15b_e0_1p8>;
+ vdd3-supply = <&vreg_l7b_e0_2p79>;
+};
+
+&smb2370_l_e2_eusb2_repeater {
+ vdd18-supply = <&vreg_l15b_e0_1p8>;
+ vdd3-supply = <&vreg_l7b_e0_2p79>;
+};
+
&tlmm {
gpio-reserved-ranges = <4 4>, /* EC TZ Secure I3C */
<10 2>, /* OOB UART */
@@ -596,3 +731,139 @@ wwan_reg_en: wwan-reg-en-state {
bias-disable;
};
};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_0_hsphy {
+ vdd-supply = <&vreg_l3f_e0_0p72>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ phys = <&smb2370_j_e2_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l3f_e0_0p72>;
+ refgen-supply = <&vreg_l2f_e0_0p82>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in1>;
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l3f_e0_0p72>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ phys = <&smb2370_k_e2_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l1h_e0_0p89>;
+ refgen-supply = <&vreg_l2f_e0_0p82>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in1>;
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in2>;
+};
+
+&usb_2_hsphy {
+ vdd-supply = <&vreg_l4c_e1_0p72>;
+ vdda12-supply = <&vreg_l4f_e1_1p08>;
+
+ phys = <&smb2370_l_e2_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy {
+ vdda-phy-supply = <&vreg_l4f_e1_1p08>;
+ vdda-pll-supply = <&vreg_l4c_e1_0p72>;
+ refgen-supply = <&vreg_l1c_e1_0p82>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in2>;
+};
+
+&usb_hs {
+ status = "okay";
+};
+
+&usb_hs_phy {
+ vdd-supply = <&vreg_l2h_e0_0p72>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ phys = <&ptn3222_2>;
+
+ status = "okay";
+};
+
+&usb_mp {
+ status = "okay";
+};
+
+&usb_mp_hsphy0 {
+ vdd-supply = <&vreg_l2h_e0_0p72>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ phys = <&ptn3222_0>;
+
+ status = "okay";
+};
+
+&usb_mp_hsphy1 {
+ vdd-supply = <&vreg_l2h_e0_0p72>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l2h_e0_0p72>;
+ refgen-supply = <&vreg_l4f_e1_1p08>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l2h_e0_0p72>;
+ refgen-supply = <&vreg_l4f_e1_1p08>;
+
+ status = "okay";
+};
--
2.48.1