[PATCH 08/12] HID: spi_hid: add device tree support for SPI over HID

[Jingyuan Liang]

From: Jarrett Schultz <jaschultz@xxxxxxxxxxxxx>

Signed-off-by: Dmitry Antipov <dmanti@xxxxxxxxxxxxx>
Signed-off-by: Jingyuan Liang <jingyliang@xxxxxxxxxxxx>
---
 drivers/hid/spi-hid/Kconfig      |  15 +++
 drivers/hid/spi-hid/Makefile     |   1 +
 drivers/hid/spi-hid/spi-hid-of.c | 243 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 259 insertions(+)

diff --git a/drivers/hid/spi-hid/Kconfig b/drivers/hid/spi-hid/Kconfig
index 114b1e00da39..76a2cd587a3e 100644
--- a/drivers/hid/spi-hid/Kconfig
+++ b/drivers/hid/spi-hid/Kconfig
@@ -25,6 +25,21 @@ config SPI_HID_ACPI
 	  will be called spi-hid-acpi. It will also build/depend on the
 	  module spi-hid.
 
+config SPI_HID_OF
+	tristate "HID over SPI transport layer Open Firmware driver"
+	depends on OF
+	select SPI_HID_CORE
+	help
+	  Say Y here if you use a keyboard, a touchpad, a touchscreen, or any
+	  other HID based devices which are connected to your computer via SPI.
+	  This driver supports Open Firmware (Device Tree)-based systems.
+
+	  If unsure, say N.
+
+	  This support is also available as a module.  If so, the module
+	  will be called spi-hid-of. It will also build/depend on the
+	  module spi-hid.
+
 config SPI_HID_CORE
 	tristate
 endif
diff --git a/drivers/hid/spi-hid/Makefile b/drivers/hid/spi-hid/Makefile
index 753c7b7a7844..fe627fd378e3 100644
--- a/drivers/hid/spi-hid/Makefile
+++ b/drivers/hid/spi-hid/Makefile
@@ -8,3 +8,4 @@
 obj-$(CONFIG_SPI_HID_CORE)	+= spi-hid.o
 spi-hid-objs 			= spi-hid-core.o
 obj-$(CONFIG_SPI_HID_ACPI)	+= spi-hid-acpi.o
+obj-$(CONFIG_SPI_HID_OF)	+= spi-hid-of.o
diff --git a/drivers/hid/spi-hid/spi-hid-of.c b/drivers/hid/spi-hid/spi-hid-of.c
new file mode 100644
index 000000000000..a20c8146230b
--- /dev/null
+++ b/drivers/hid/spi-hid/spi-hid-of.c
@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * HID over SPI protocol, Open Firmware related code
+ *
+ * Copyright (c) 2021 Microsoft Corporation
+ *
+ * This code was forked out of the HID over SPI core code, which is partially
+ * based on "HID over I2C protocol implementation:
+ *
+ * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@xxxxxxxxx>
+ * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France
+ * Copyright (c) 2012 Red Hat, Inc
+ *
+ * which in turn is partially based on "USB HID support for Linux":
+ *
+ * Copyright (c) 1999 Andreas Gal
+ * Copyright (c) 2000-2005 Vojtech Pavlik <vojtech@xxxxxxx>
+ * Copyright (c) 2005 Michael Haboustak <mike-@xxxxxxxxxxxx> for Concept2, Inc
+ * Copyright (c) 2007-2008 Oliver Neukum
+ * Copyright (c) 2006-2010 Jiri Kosina
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
+
+#include "spi-hid.h"
+
+/* Config structure is filled with data from Device Tree */
+struct spi_hid_of_config {
+	struct spihid_ops ops;
+
+	struct spi_hid_conf property_conf;
+	u32 post_power_on_delay_ms;
+	u32 minimal_reset_delay_ms;
+	struct gpio_desc *reset_gpio;
+	struct regulator *supply;
+	bool supply_enabled;
+};
+
+static int spi_hid_of_populate_config(struct spi_hid_of_config *conf,
+				      struct device *dev)
+{
+	int error;
+	u32 val;
+
+	error = device_property_read_u32(dev, "input-report-header-address",
+					 &val);
+	if (error) {
+		dev_err(dev, "Input report header address not provided.");
+		return -ENODEV;
+	}
+	conf->property_conf.input_report_header_address = val;
+
+	error = device_property_read_u32(dev, "input-report-body-address", &val);
+	if (error) {
+		dev_err(dev, "Input report body address not provided.");
+		return -ENODEV;
+	}
+	conf->property_conf.input_report_body_address = val;
+
+	error = device_property_read_u32(dev, "output-report-address", &val);
+	if (error) {
+		dev_err(dev, "Output report address not provided.");
+		return -ENODEV;
+	}
+	conf->property_conf.output_report_address = val;
+
+	error = device_property_read_u32(dev, "read-opcode", &val);
+	if (error) {
+		dev_err(dev, "Read opcode not provided.");
+		return -ENODEV;
+	}
+	conf->property_conf.read_opcode = val;
+
+	error = device_property_read_u32(dev, "write-opcode", &val);
+	if (error) {
+		dev_err(dev, "Write opcode not provided.");
+		return -ENODEV;
+	}
+	conf->property_conf.write_opcode = val;
+
+	error = device_property_read_u32(dev, "post-power-on-delay-ms", &val);
+	if (error) {
+		dev_err(dev, "post-power-on-delay-ms not provided, using 10.");
+		val = 10;
+	}
+	conf->post_power_on_delay_ms = val;
+
+	error = device_property_read_u32(dev, "minimal-reset-delay-ms", &val);
+	if (error) {
+		dev_err(dev, "minimal-reset-delay-ms not provided, using 100.");
+		val = 100;
+	}
+	conf->minimal_reset_delay_ms = val;
+
+	/* FIXME: not reading hid-over-spi-flags, multi-fragment not supported */
+
+	conf->supply = devm_regulator_get(dev, "vdd");
+	if (IS_ERR(conf->supply)) {
+		if (PTR_ERR(conf->supply) != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get regulator: %ld.",
+				PTR_ERR(conf->supply));
+		return PTR_ERR(conf->supply);
+	}
+	conf->supply_enabled = false;
+
+	conf->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(conf->reset_gpio)) {
+		dev_err(dev, "%s: error getting reset GPIO.", __func__);
+		return PTR_ERR(conf->reset_gpio);
+	}
+
+	return 0;
+}
+
+static int spi_hid_of_power_down(struct spihid_ops *ops)
+{
+	struct spi_hid_of_config *conf = container_of(ops,
+						      struct spi_hid_of_config,
+						      ops);
+	int error;
+
+	if (!conf->supply_enabled)
+		return 0;
+
+	error = regulator_disable(conf->supply);
+	if (error == 0)
+		conf->supply_enabled = false;
+
+	return error;
+}
+
+static int spi_hid_of_power_up(struct spihid_ops *ops)
+{
+	struct spi_hid_of_config *conf = container_of(ops,
+						      struct spi_hid_of_config,
+						      ops);
+	int error;
+
+	if (conf->supply_enabled)
+		return 0;
+
+	error = regulator_enable(conf->supply);
+
+	if (error == 0) {
+		conf->supply_enabled = true;
+		usleep_range(1000 * conf->post_power_on_delay_ms,
+			     1000 * (conf->post_power_on_delay_ms + 1));
+	}
+
+	return error;
+}
+
+static int spi_hid_of_assert_reset(struct spihid_ops *ops)
+{
+	struct spi_hid_of_config *conf = container_of(ops,
+						      struct spi_hid_of_config,
+						      ops);
+
+	gpiod_set_value(conf->reset_gpio, 1);
+	return 0;
+}
+
+static int spi_hid_of_deassert_reset(struct spihid_ops *ops)
+{
+	struct spi_hid_of_config *conf = container_of(ops,
+						      struct spi_hid_of_config,
+						      ops);
+
+	gpiod_set_value(conf->reset_gpio, 0);
+	return 0;
+}
+
+static void spi_hid_of_sleep_minimal_reset_delay(struct spihid_ops *ops)
+{
+	struct spi_hid_of_config *conf = container_of(ops,
+						      struct spi_hid_of_config,
+						      ops);
+	usleep_range(1000 * conf->minimal_reset_delay_ms,
+		     1000 * (conf->minimal_reset_delay_ms + 1));
+}
+
+static int spi_hid_of_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct spi_hid_of_config *config;
+	int error;
+
+	config = devm_kzalloc(dev, sizeof(struct spi_hid_of_config),
+			      GFP_KERNEL);
+	if (!config)
+		return -ENOMEM;
+
+	config->ops.power_up = spi_hid_of_power_up;
+	config->ops.power_down = spi_hid_of_power_down;
+	config->ops.assert_reset = spi_hid_of_assert_reset;
+	config->ops.deassert_reset = spi_hid_of_deassert_reset;
+	config->ops.sleep_minimal_reset_delay =
+		spi_hid_of_sleep_minimal_reset_delay;
+
+	error = spi_hid_of_populate_config(config, dev);
+	if (error) {
+		dev_err(dev, "%s: unable to populate config data.", __func__);
+		return error;
+	}
+
+	return spi_hid_core_probe(spi, &config->ops, &config->property_conf);
+}
+
+const struct of_device_id spi_hid_of_match[] = {
+	{ .compatible = "hid-over-spi" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, spi_hid_of_match);
+
+static const struct spi_device_id spi_hid_of_id_table[] = {
+	{ "hid", 0 },
+	{ "hid-over-spi", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, spi_hid_of_id_table);
+
+static struct spi_driver spi_hid_of_driver = {
+	.driver = {
+		.name	= "spi_hid_of",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(spi_hid_of_match),
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+		.dev_groups = spi_hid_groups,
+	},
+	.probe		= spi_hid_of_probe,
+	.remove		= spi_hid_core_remove,
+	.id_table	= spi_hid_of_id_table,
+};
+
+module_spi_driver(spi_hid_of_driver);
+
+MODULE_DESCRIPTION("HID over SPI OF transport driver");
+MODULE_AUTHOR("Dmitry Antipov <dmanti@xxxxxxxxxxxxx>");
+MODULE_LICENSE("GPL");

-- 
2.53.0.473.g4a7958ca14-goog