Re: [PATCH RFC v11 00/12] crypto/dmaengine: qce: introduce BAM locking and use DMA for register I/O

[Bartosz Golaszewski]

On Thu, Mar 5, 2026 at 2:43 PM Stephan Gerhold
<stephan.gerhold@xxxxxxxxxx> wrote:
>
> On Thu, Mar 05, 2026 at 02:10:55PM +0100, Bartosz Golaszewski wrote:
> > On Thu, Mar 5, 2026 at 1:00 PM Stephan Gerhold
> > <stephan.gerhold@xxxxxxxxxx> wrote:
> > >
> > > On Tue, Mar 03, 2026 at 06:13:56PM +0530, Manivannan Sadhasivam wrote:
> > > > On Mon, Mar 02, 2026 at 04:57:13PM +0100, Bartosz Golaszewski wrote:
> > > > > NOTE: Please note that even though this is version 11, I changed the
> > > > > prefix to RFC as this is an entirely new approach resulting from
> > > > > discussions under v9. I AM AWARE of the existing memory leaks in the
> > > > > last patch of this series - I'm sending it because I want to first
> > > > > discuss the approach and get a green light from Vinod as well as Mani
> > > > > and Bjorn. Especially when it comes to communicating the address for the
> > > > > dummy rights from the client to the BAM driver.
> > > > > /NOTE
> > > > >
> > > > > Currently the QCE crypto driver accesses the crypto engine registers
> > > > > directly via CPU. Trust Zone may perform crypto operations simultaneously
> > > > > resulting in a race condition. To remedy that, let's introduce support
> > > > > for BAM locking/unlocking to the driver. The BAM driver will now wrap
> > > > > any existing issued descriptor chains with additional descriptors
> > > > > performing the locking when the client starts the transaction
> > > > > (dmaengine_issue_pending()). The client wanting to profit from locking
> > > > > needs to switch to performing register I/O over DMA and communicate the
> > > > > address to which to perform the dummy writes via a call to
> > > > > dmaengine_slave_config().
> > > > >
> > > >
> > > > Thanks for moving the LOCK/UNLOCK bits out of client to the BAM driver. It looks
> > > > neat now. I understand the limitation that for LOCK/UNLOCK, BAM needs to perform
> > > > a dummy write to an address in the client register space. So in this case, you
> > > > can also use the previous metadata approach to pass the scratchpad register to
> > > > the BAM driver from clients. The BAM driver can use this register to perform
> > > > LOCK/UNLOCK.
> > > >
> > > > It may sound like I'm suggesting a part of your previous design, but it fits the
> > > > design more cleanly IMO. The BAM performs LOCK/UNLOCK on its own, but it gets
> > > > the scratchpad register address from the clients through the metadata once.
> > > >
> > > > It is very unfortunate that the IP doesn't accept '0' address for LOCK/UNLOCK or
> > > > some of them cannot append LOCK/UNLOCK to the actual CMD descriptors passed from
> > > > the clients. These would've made the code/design even more cleaner.
> > > >
> > >
> > > I was staring at the downstream drivers for QCE (qce50.c?) [1] for a bit
> > > and my impression is that they manage to get along without dummy writes.
> > > It's a big mess, but it looks like they always have some commands
> > > (depending on the crypto operation) that they are sending anyway and
> > > they just assign the LOCK/UNLOCK flag to the command descriptor of that.
> > >
> > > It is similar for the second relevant user of the LOCK/UNLOCK flags, the
> > > QPIC NAND driver (msm_qpic_nand.c in downstream [2], qcom_nandc.c in
> > > mainline), it is assigned as part of the register programming sequence
> > > instead of using a dummy write. In addition, the UNLOCK flag is
> > > sometimes assigned to a READ command descriptor rather than a WRITE.
> > >
> > > @Bartosz: Can we get by without doing any dummy writes?
> > > If not, would a dummy read perhaps be less intrusive than a dummy write?
> > >
> >
> > The HPG says that the LOCK/UNLOCK flag *must* be set on a command
> > descriptor, not a data descriptor. For a simple encryption we will
> > typically have a data descriptor and a command descriptor with
> > register writes. So we need a command descriptor in front of the data
> > and - while we could technically set the UNLOCK bit on the subsequent
> > command descriptor - it's unclear from the HPG whether it will unlock
> > before or after processing the command descriptor with the UNLOCK bit
> > set. Hence the additional command descriptor at the end.
> >
>
> I won't pretend that I actually understand what the downstream QCE
> driver is doing, but e.g. qce_ablk_cipher_req() in the qce50.c I linked
> looks like they just put the command descriptor with all the register
> writes first and then the data second (followed by another command
> descriptor for cleanup/unlocking). Is it actually required to put the
> data first?
>

Well, now you're getting into the philosophical issue of imposing
requirements on the client which seemed to be the main point of
contention in earlier versions. If you start requiring the client to
put the DMA operations in a certain order (and it's not based on any
HW requirement but rather on how the DMA driver is implemented) then
how is it better than having the client just drive the locking
altogether like pre v11? We won't get away without at least some
requirements - like the client doing register I/O over DMA or
providing the scratchpad address - but I think just wrapping the
existing queue with additional descriptors in a way transparent to
consumers is better in this case. And as I said: the HPG doesn't
explicitly say that it unlocks the pipe *after* the descriptor with
the unlock bit is processed. Doesn't even hint at what real the
ordering is.

> > The HPG also only mentions a write command and says nothing about a
> > read. In any case: that's the least of the problems as switching to
> > read doesn't solve the issue of passing the address of the scratchpad
> > register.
>
> True.
>
> >
> > So while some of this *may* just work, I would prefer to stick to what
> > documentation says *will* work. :)
> >
>
> Well, the question is if there is always a dummy register that can be
> safely written (without causing any side effects). This will be always
> just based on experiments, since the concept of a dummy write doesn't
> seem to exist downstream (and I assume the documentation doesn't suggest
> a specific register to use either).
>

You'd think so but the HPG actually does use the word "dummy" to
describe the write operation with lock/unlock bits set. Though it does
not recommend any particular register to do it.

> NAND_VERSION (0xf08) might work for qcom_nandc.c (which might be the
> only other relevant user of the BAM locking functionality...).
>

Yeah, I do the same for QCE, write to the version register.

Bart