[PATCH 2/6] arm64: dts: freescale: Add Verdin iMX95 support

[Ernest Van Hoecke]

From: Ernest Van Hoecke <ernest.vanhoecke@xxxxxxxxxxx>

Add support for the Toradex Verdin iMX95 and its development carrier
board.

The module consists of an NXP i.MX95 family SoC, up to 16GB LPDDR4x RAM,
up to 128GB of storage, a USB 3.2 OTG and USB 2.0 Host, a Gigabit
Ethernet PHY, an I2C EEPROM and Temperature Sensor, an RX8130 RTC, an
I3C bus, one Quad lane CSI interface, one Quad lane DSI or CSI
interface, one LVDS interface (one or two channels), and some optional
addons: TPM 2.0, and a WiFi/BT module.

Link: https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
Link: https://www.toradex.com/products/carrier-board/verdin-development-board-kit
Co-developed-by: Emanuele Ghidoli <emanuele.ghidoli@xxxxxxxxxxx>
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@xxxxxxxxxxx>
Co-developed-by: Francesco Dolcini <francesco.dolcini@xxxxxxxxxxx>
Signed-off-by: Francesco Dolcini <francesco.dolcini@xxxxxxxxxxx>
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@xxxxxxxxxxx>
---
 arch/arm64/boot/dts/freescale/Makefile             |    2 +
 .../arm64/boot/dts/freescale/imx95-verdin-dev.dtsi |  250 +++++
 .../dts/freescale/imx95-verdin-nonwifi-dev.dts     |   21 +
 .../boot/dts/freescale/imx95-verdin-nonwifi.dtsi   |   16 +
 .../boot/dts/freescale/imx95-verdin-wifi-dev.dts   |   21 +
 .../boot/dts/freescale/imx95-verdin-wifi.dtsi      |   50 +
 arch/arm64/boot/dts/freescale/imx95-verdin.dtsi    | 1162 ++++++++++++++++++++
 7 files changed, 1522 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index e0738525d37e..12cbb60cb0cd 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -452,6 +452,8 @@ dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk-sof.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-toradex-smarc-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx95-tqma9596sa-mb-smarc-2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-verdin-nonwifi-dev.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-verdin-wifi-dev.dtb
 
 imx95-15x15-evk-pcie0-ep-dtbs = imx95-15x15-evk.dtb imx-pcie0-ep.dtbo
 dtb-$(CONFIG_ARCH_MXC) += imx95-15x15-evk-pcie0-ep.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx95-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx95-verdin-dev.dtsi
new file mode 100644
index 000000000000..2848f9adf152
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-verdin-dev.dtsi
@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Common dtsi for Verdin iMX95 SoM on development carrier board
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ * https://www.toradex.com/products/carrier-board/verdin-development-board-kit
+ */
+
+/ {
+	aliases {
+		eeprom1 = &carrier_eeprom;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,name = "verdin-nau8822";
+		simple-audio-card,routing =
+			"Headphones", "LHP",
+			"Headphones", "RHP",
+			"Speaker", "LSPK",
+			"Speaker", "RSPK",
+			"Line Out", "AUXOUT1",
+			"Line Out", "AUXOUT2",
+			"LAUX", "Line In",
+			"RAUX", "Line In",
+			"LMICP", "Mic In",
+			"RMICP", "Mic In";
+		simple-audio-card,widgets =
+			"Headphones", "Headphones",
+			"Line Out", "Line Out",
+			"Speaker", "Speaker",
+			"Microphone", "Mic In",
+			"Line", "Line In";
+
+		codec_dai: simple-audio-card,codec {
+			clocks = <&scmi_clk IMX95_CLK_SAI3>;
+			sound-dai = <&nau8822_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+		};
+	};
+};
+
+/* Verdin ADC_1, ADC_2, ADC_3 and ADC_4 */
+&adc1 {
+	status = "okay";
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&enetc_port0 {
+	status = "okay";
+};
+
+/* Verdin ETH_2_RGMII */
+&enetc_port1 {
+	phy-handle = <&ethphy2>;
+	phy-mode = "rgmii-id";
+
+	status = "okay";
+};
+
+/* Verdin CAN_1 */
+&flexcan1 {
+	status = "okay";
+};
+
+/* Verdin CAN_2 */
+&flexcan2 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi1 {
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>,
+		    <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>;
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio6>;
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio5>;
+};
+
+&gpio5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+};
+
+/* Verdin I2C_3_HDMI */
+&i3c2 {
+	status = "okay";
+};
+
+/* Verdin I2C_2_DSI */
+&lpi2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&lpi2c4 {
+	status = "okay";
+
+	nau8822_1a: audio-codec@1a {
+		compatible = "nuvoton,nau8822";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sai3_mclk>;
+		#sound-dai-cells = <0>;
+	};
+
+	carrier_gpio_expander: gpio@21 {
+		compatible = "nxp,pcal6416";
+		reg = <0x21>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	/* Current measurement into module VCC */
+	hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+	};
+
+	temperature-sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+	};
+
+	carrier_eeprom: eeprom@57 {
+		compatible = "st,24c02", "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+	};
+};
+
+/* Verdin I2C_4_CSI */
+&lpi2c5 {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux console */
+&lpuart1 {
+	status = "okay";
+};
+
+/* Verdin UART_4 */
+&lpuart2 {
+	status = "okay";
+};
+
+/* Verdin UART_1, connector X50 through RS485 transceiver */
+&lpuart7 {
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+	linux,rs485-enabled-at-boot-time;
+
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&lpuart8 {
+	status = "okay";
+};
+
+&netc_emdio {
+	ethphy2: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_eth2_rgmii_int>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+		micrel,led-mode = <0>;
+	};
+};
+
+/* Verdin PCIE_1 */
+&pcie0 {
+	status = "okay";
+};
+
+/* Verdin I2S_1 */
+&sai3 {
+	status = "okay";
+};
+
+/* Verdin PWM_1 */
+&tpm4 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&tpm5 {
+	status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&tpm6 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usb2 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usb3 {
+	fsl,permanently-attached;
+
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	status = "okay";
+};
+
+/* Verdin CTRL_WAKE1_MICO# */
+&verdin_gpio_keys {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx95-verdin-nonwifi-dev.dts b/arch/arm64/boot/dts/freescale/imx95-verdin-nonwifi-dev.dts
new file mode 100644
index 000000000000..97636ec7c26a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-verdin-nonwifi-dev.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ * https://www.toradex.com/products/carrier-board/verdin-development-board-kit
+ */
+
+/dts-v1/;
+
+#include "imx95-verdin.dtsi"
+#include "imx95-verdin-nonwifi.dtsi"
+#include "imx95-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX95 on Verdin Development Board";
+	compatible = "toradex,verdin-imx95-nonwifi-dev",
+		     "toradex,verdin-imx95-nonwifi",
+		     "toradex,verdin-imx95",
+		     "fsl,imx95";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx95-verdin-nonwifi.dtsi b/arch/arm64/boot/dts/freescale/imx95-verdin-nonwifi.dtsi
new file mode 100644
index 000000000000..7aba22067de5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-verdin-nonwifi.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Common dtsi for Verdin iMX95 SoM non-WB variant
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ */
+
+/* SDIO on MSP 30, 31, 32, 33, 34, 35 */
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx95-verdin-wifi-dev.dts b/arch/arm64/boot/dts/freescale/imx95-verdin-wifi-dev.dts
new file mode 100644
index 000000000000..345d37247025
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-verdin-wifi-dev.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ * https://www.toradex.com/products/carrier-board/verdin-development-board-kit
+ */
+
+/dts-v1/;
+
+#include "imx95-verdin.dtsi"
+#include "imx95-verdin-wifi.dtsi"
+#include "imx95-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX95 WB on Verdin Development Board";
+	compatible = "toradex,verdin-imx95-wifi-dev",
+		     "toradex,verdin-imx95-wifi",
+		     "toradex,verdin-imx95",
+		     "fsl,imx95";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx95-verdin-wifi.dtsi b/arch/arm64/boot/dts/freescale/imx95-verdin-wifi.dtsi
new file mode 100644
index 000000000000..256c9ed04605
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-verdin-wifi.dtsi
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Common dtsi for Verdin iMX95 SoM WB variant
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ */
+
+/ {
+	reg_wifi_en: regulator-wifi-en {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		/* PMIC_EN_WIFI */
+		gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "PDn_MAYA-W260";
+		startup-delay-us = <2000>;
+	};
+};
+
+/* On-module Bluetooth */
+&lpuart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_bt_uart>;
+	uart-has-rtscts;
+
+	status = "okay";
+
+	som_bt: bluetooth {
+		compatible = "nxp,88w8987-bt";
+		fw-init-baudrate = <3000000>;
+	};
+};
+
+/* On-module Wi-Fi */
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	keep-power-in-suspend;
+	non-removable;
+	vmmc-supply = <&reg_wifi_en>;
+
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx95-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx95-verdin.dtsi
new file mode 100644
index 000000000000..6c9fd6f86414
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-verdin.dtsi
@@ -0,0 +1,1162 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Common dtsi for Verdin iMX95 SoM
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include "imx95.dtsi"
+
+/ {
+	aliases {
+		can0 = &flexcan1;
+		can1 = &flexcan2;
+		eeprom0 = &som_eeprom;
+		ethernet0 = &enetc_port0;
+		ethernet1 = &enetc_port1;
+		i2c0 = &lpi2c2;
+		i2c1 = &lpi2c4;
+		i2c2 = &lpi2c3;
+		i2c3 = &i3c2;
+		i2c4 = &lpi2c5;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc3;
+		rtc0 = &rtc_i2c;
+		rtc1 = &scmi_bbm;
+		serial0 = &lpuart7;
+		serial1 = &lpuart8;
+		serial2 = &lpuart1;
+		serial3 = &lpuart2;
+		serial4 = &lpuart6;
+		usb0 = &usb2;
+		usb1 = &usb3;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	cm7: remoteproc-cm7 {
+		compatible = "fsl,imx95-cm7";
+		mbox-names = "tx", "rx", "rxdb";
+		mboxes = <&mu7 0 1
+			  &mu7 1 1
+			  &mu7 3 1>;
+		memory-region = <&vdevbuffer>, <&vdev0vring0>, <&vdev0vring1>,
+				<&vdev1vring0>, <&vdev1vring1>, <&rsc_table>, <&m7_reserved>;
+	};
+
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		/* Verdin USB_1_ID (SODIMM 161) */
+		id-gpios = <&som_gpio_expander 5 GPIO_ACTIVE_HIGH>;
+		label = "USB_1";
+		self-powered;
+		vbus-supply = <&reg_usb1_vbus>;
+
+		port {
+			usb_dr_connector: endpoint {
+				remote-endpoint = <&usb1_id>;
+			};
+		};
+	};
+
+	verdin_gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_wake1_mico>;
+
+		status = "disabled";
+
+		verdin_key_wakeup: key-wakeup {
+			/* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "On-module +V1.8";
+	};
+
+	/*
+	 * By default we enable CTRL_SLEEP_MOCI#, this is required to have
+	 * peripherals on the carrier board powered.
+	 * If more granularity or power saving is required this can be disabled
+	 * in the carrier board device tree files.
+	 */
+	reg_force_sleep_moci: regulator-force-sleep-moci {
+		compatible = "regulator-fixed";
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "CTRL_SLEEP_MOCI#";
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		/* Verdin USB_1_EN (SODIMM 155) */
+		gpios = <&som_gpio_expander 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "USB_1_EN";
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		/* Verdin USB_2_EN (SODIMM 185) */
+		gpios = <&som_gpio_expander 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "USB_2_EN";
+	};
+
+	reg_usdhc2_vmmc: regulator-vmmc-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr_en>;
+		/* Verdin SD_1_PWR_EN (SODIMM 76) */
+		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		off-on-delay-us = <100000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "SD_1_PWR_EN";
+		startup-delay-us = <20000>;
+	};
+
+	reg_usdhc2_vqmmc: regulator-usdhc2-vqmmc {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_vsel>;
+		gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <1800000>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
+		regulator-name = "PMIC_SD2_VSEL";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		linux_cma: linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0 0x3c000000>;
+			alloc-ranges = <0 0x80000000 0 0x7F000000>;
+			linux,cma-default;
+		};
+
+		m7_reserved: memory@80000000 {
+			reg = <0 0x80000000 0 0x1000000>;
+			no-map;
+		};
+
+		rsc_table: rsc-table@88220000 {
+			reg = <0 0x88220000 0 0x1000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@88000000 {
+			reg = <0 0x88000000 0 0x8000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@88008000 {
+			reg = <0 0x88008000 0 0x8000>;
+			no-map;
+		};
+
+		vdev1vring0: vdev1vring0@88010000 {
+			reg = <0 0x88010000 0 0x8000>;
+			no-map;
+		};
+
+		vdev1vring1: vdev1vring1@88018000 {
+			reg = <0 0x88018000 0 0x8000>;
+			no-map;
+		};
+
+		vdevbuffer: vdevbuffer@88020000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x88020000 0 0x100000>;
+			no-map;
+		};
+	};
+};
+
+/* Verdin ADC_1, ADC_2, ADC_3 and ADC_4 */
+&adc1 {
+	vref-supply = <&reg_1p8v>;
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&enetc_port0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enetc0>;
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+};
+
+/* Verdin ETH_2_RGMII */
+&enetc_port1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enetc1>;
+};
+
+/* Verdin CAN_1 */
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+};
+
+/* Verdin CAN_2 */
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+};
+
+/* Verdin QSPI_1 */
+&flexspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi1>;
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", /* 0 */
+		"",
+		"",
+		"",
+		"SODIMM_147",
+		"SODIMM_149",
+		"SODIMM_151",
+		"SODIMM_153",
+		"SODIMM_20",
+		"SODIMM_22",
+		"SODIMM_252", /* 10 */
+		"",
+		"SODIMM_189",
+		"IO_EXP_INT",
+		"SODIMM_256",
+		"";
+
+	status = "okay";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"SODIMM_206", /* 0 */
+		"SODIMM_198",
+		"SODIMM_200",
+		"SODIMM_196",
+		"",
+		"SODIMM_15",
+		"SODIMM_16",
+		"",
+		"SODIMM_131",
+		"SODIMM_129",
+		"SODIMM_135", /* 10 */
+		"SODIMM_133",
+		"SODIMM_139",
+		"SODIMM_137",
+		"SODIMM_143",
+		"SODIMM_141",
+		"SODIMM_30",
+		"SODIMM_38",
+		"SODIMM_208",
+		"SODIMM_19",
+		"SODIMM_36", /* 20 */
+		"SODIMM_34",
+		"SODIMM_93",
+		"SODIMM_95",
+		"SODIMM_210",
+		"SODIMM_24",
+		"SODIMM_32",
+		"SODIMM_26",
+		"SODIMM_53",
+		"SODIMM_55",
+		"SODIMM_12", /* 30 */
+		"SODIMM_14";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"SODIMM_84", /* 0 */
+		"SODIMM_78",
+		"SODIMM_74",
+		"SODIMM_80",
+		"SODIMM_82",
+		"SODIMM_70",
+		"SODIMM_72",
+		"SODIMM_76",
+		"",
+		"",
+		"", /* 10 */
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"PMIC_SD2_VSEL",
+		"", /* 20 */
+		"",
+		"",
+		"",
+		"",
+		"",
+		"SODIMM_91",
+		"SODIMM_218",
+		"",
+		"",
+		"", /* 30 */
+		"";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"SODIMM_59", /* 0 */
+		"SODIMM_57",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"", /* 10 */
+		"",
+		"",
+		"",
+		"SODIMM_193",
+		"SODIMM_191",
+		"SODIMM_215",
+		"SODIMM_217",
+		"SODIMM_219",
+		"SODIMM_221",
+		"SODIMM_211", /* 20 */
+		"SODIMM_213",
+		"SODIMM_199",
+		"SODIMM_197",
+		"SODIMM_201",
+		"SODIMM_203",
+		"SODIMM_205",
+		"SODIMM_207",
+		"SODIMM_216",
+		"SODIMM_202";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"SODIMM_56", /* 0 */
+		"SODIMM_58",
+		"SODIMM_60",
+		"SODIMM_62",
+		"SODIMM_46",
+		"SODIMM_44",
+		"SODIMM_42",
+		"SODIMM_48",
+		"SODIMM_66",
+		"SODIMM_52",
+		"SODIMM_54", /* 10 */
+		"SODIMM_64",
+		"SODIMM_212",
+		"",
+		"",
+		"",
+		"",
+		"";
+};
+
+/* Verdin I2C_3_HDMI */
+&i3c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i3c2>;
+	i2c-scl-hz = <400000>;
+};
+
+/* CTRL_I2C (On-module I2C) */
+&lpi2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_lpi2c2>, <&pinctrl_io_exp_int>;
+	pinctrl-1 = <&pinctrl_lpi2c2_gpio>, <&pinctrl_io_exp_int>;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	single-master;
+
+	status = "okay";
+
+	som_gpio_expander: gpio@20 {
+		compatible = "nxp,pcal6416";
+		reg = <0x20>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+		#gpio-cells = <2>;
+		gpio-controller;
+
+		gpio-line-names =
+			"SODIMM_220", /* 0 */
+			"SODIMM_222",
+			"SODIMM_17",
+			"SODIMM_21",
+			"SODIMM_244",
+			"SODIMM_161",
+			"SODIMM_157",
+			"SODIMM_155",
+			"SODIMM_185",
+			"SODIMM_187",
+			"USB_RECOV_CTRL#", /* 10 */
+			"ENET1_INT#",
+			"TPM_INT#",
+			"TPM_CS#",
+			"",
+			"";
+
+		/*
+		 * Switch USB to default position:
+		 *   - SoC USB2 -> Verdin USB_1
+		 *   - SoC USB1 -> Verdin USB_2
+		 * Reset configuration:
+		 *   - SoC USB1 -> Verdin USB_1 (USB recovery)
+		 *   - SoC USB2 not connected
+		 */
+		usb_recov_ctrl: usb-recov-ctrl-hog {
+			gpio-hog;
+			gpios = <10 GPIO_ACTIVE_HIGH>;
+			line-name = "USB_RECOV_CTRL#";
+			output-high;
+		};
+	};
+
+	rtc_i2c: rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+	};
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp1075";
+		reg = <0x48>;
+	};
+
+	som_eeprom: eeprom@50 {
+		compatible = "st,24c02", "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+/* Verdin I2C_2_DSI */
+&lpi2c3 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+	pinctrl-1 = <&pinctrl_lpi2c3_gpio>;
+	clock-frequency = <100000>;
+	scl-gpios = <&gpio2 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio2 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	single-master;
+};
+
+/* Verdin I2C_1 */
+&lpi2c4 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_lpi2c4>;
+	pinctrl-1 = <&pinctrl_lpi2c4_gpio>;
+	clock-frequency = <100000>;
+	scl-gpios = <&gpio2 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	single-master;
+};
+
+/* Verdin I2C_4_CSI */
+&lpi2c5 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_lpi2c5>;
+	pinctrl-1 = <&pinctrl_lpi2c5_gpio>;
+	clock-frequency = <100000>;
+	scl-gpios = <&gpio2 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio2 22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	single-master;
+};
+
+/* Verdin SPI_1 */
+&lpspi6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpspi6>, <&pinctrl_spi1_cs>;
+	cs-gpios = <&gpio4 29 GPIO_ACTIVE_LOW>,
+		   <&som_gpio_expander 13 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+
+	som_tpm: tpm@1 {
+		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+		reg = <0x1>;
+		interrupt-parent = <&som_gpio_expander>;
+		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+		/*
+		 * Maximum TPM-supported speed is 18.5 MHz, limited to 12 MHz
+		 * here as lpspi6's per-clock (twice the max speed) is 24 MHz
+		 */
+		spi-max-frequency = <12000000>;
+	};
+};
+
+/* Verdin UART_3, used as the Linux console */
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+/* Verdin UART_4 */
+&lpuart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+};
+
+/* Verdin UART_1 */
+&lpuart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart7>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_2 */
+&lpuart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart8>;
+	uart-has-rtscts;
+};
+
+&mu7 {
+	status = "okay";
+};
+
+&netc_blk_ctrl {
+	status = "okay";
+};
+
+&netc_bus0 {
+	msi-map = <0x0 &its 0x60 0x1>,	//ENETC0 PF
+		  <0x10 &its 0x61 0x1>, //ENETC0 VF0
+		  <0x20 &its 0x62 0x1>, //ENETC0 VF1
+		  <0x40 &its 0x63 0x1>, //ENETC1 PF
+		  <0x50 &its 0x65 0x1>, //ENETC1 VF0
+		  <0x60 &its 0x66 0x1>, //ENETC1 VF1
+		  <0x80 &its 0x64 0x1>, //ENETC2 PF
+		  <0xc0 &its 0x67 0x1>; //NETC Timer
+	iommu-map = <0x0 &smmu 0x20 0x1>,
+		    <0x10 &smmu 0x21 0x1>,
+		    <0x20 &smmu 0x22 0x1>,
+		    <0x40 &smmu 0x23 0x1>,
+		    <0x50 &smmu 0x25 0x1>,
+		    <0x60 &smmu 0x26 0x1>,
+		    <0x80 &smmu 0x24 0x1>,
+		    <0xc0 &smmu 0x27 0x1>;
+};
+
+/* Verdin ETH_2_RGMII_MDIO, shared between all ethernet ports */
+&netc_emdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_emdio>;
+
+	status = "okay";
+
+	ethphy1: ethernet-phy@0 {
+		reg = <0>;
+		interrupt-parent = <&som_gpio_expander>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+	};
+};
+
+&netc_timer {
+	status = "okay";
+};
+
+&netcmix_blk_ctrl {
+	status = "okay";
+};
+
+/* Verdin PCIE_1 */
+&pcie0 {
+	/* PCIE_1_RESET# (SODIMM 244) */
+	reset-gpios = <&som_gpio_expander 4 GPIO_ACTIVE_LOW>;
+};
+
+/* Verdin I2S_1 */
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL1>,
+			  <&scmi_clk IMX95_CLK_AUDIOPLL2>,
+			  <&scmi_clk IMX95_CLK_SAI3>;
+	assigned-clock-parents = <0>, <0>, <0>, <0>,
+				 <&scmi_clk IMX95_CLK_AUDIOPLL1>;
+	assigned-clock-rates = <3932160000>,
+			       <3612672000>, <393216000>,
+			       <361267200>, <12288000>;
+	#sound-dai-cells = <0>;
+	fsl,sai-mclk-direction-output;
+};
+
+&scmi_bbm {
+	linux,code = <KEY_POWER>;
+};
+
+&thermal_zones {
+	/* PF09 Main PMIC */
+	pf09-thermal {
+		polling-delay = <2000>;
+		polling-delay-passive = <250>;
+		thermal-sensors = <&scmi_sensor 2>;
+
+		trips {
+			trip0 {
+				hysteresis = <2000>;
+				temperature = <155000>;
+				type = "critical";
+			};
+		};
+	};
+
+	/* PF53 VDD_ARM PMIC */
+	pf53-arm-thermal {
+		polling-delay = <2000>;
+		polling-delay-passive = <250>;
+		thermal-sensors = <&scmi_sensor 4>;
+
+		trips {
+			trip0 {
+				hysteresis = <2000>;
+				temperature = <155000>;
+				type = "critical";
+			};
+		};
+	};
+
+	/* PF53 VDD_SOC PMIC */
+	pf53-soc-thermal {
+		polling-delay = <2000>;
+		polling-delay-passive = <250>;
+		thermal-sensors = <&scmi_sensor 3>;
+
+		trips {
+			trip0 {
+				hysteresis = <2000>;
+				temperature = <155000>;
+				type = "critical";
+			};
+		};
+	};
+};
+
+/* Verdin PWM_1 */
+&tpm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm4>;
+};
+
+/* Verdin PWM_2 */
+&tpm5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm5>;
+};
+
+/* Verdin PWM_3_DSI */
+&tpm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tpm6>;
+};
+
+/* Verdin USB_1 */
+&usb2 {
+	dr_mode = "otg";
+	adp-disable;
+	hnp-disable;
+	srp-disable;
+	usb-role-switch;
+	vbus-supply = <&reg_usb1_vbus>;
+
+	port {
+		usb1_id: endpoint {
+			remote-endpoint = <&usb_dr_connector>;
+		};
+	};
+};
+
+/* Verdin USB_2 */
+&usb3 {
+	fsl,disable-port-power-control;
+};
+
+&usb3_dwc3 {
+	dr_mode = "host";
+};
+
+&usb3_phy {
+	vbus-supply = <&reg_usb2_vbus>;
+};
+
+/* On-module eMMC */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	no-sdio;
+	no-sd;
+
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>,<&pinctrl_usdhc2_cd>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_cd>;
+	cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	vqmmc-supply = <&reg_usdhc2_vqmmc>;
+};
+
+&wdog3 {
+	fsl,ext-reset-output;
+
+	status = "okay";
+};
+
+&scmi_iomuxc {
+	/* On-module Bluetooth on WB SKUs, module-specific UART otherwise */
+	pinctrl_bt_uart: btuartgrp {
+		fsl,pins = <IMX95_PAD_GPIO_IO04__LPUART6_TX	0x31e>, /* WiFi_UART_SoC_TXD */
+			   <IMX95_PAD_GPIO_IO33__LPUART6_RX	0x31e>, /* WiFi_UART_SoC_RXD */
+			   <IMX95_PAD_GPIO_IO34__LPUART6_CTS_B	0x31e>, /* WiFi_UART_SoC_CTS */
+			   <IMX95_PAD_GPIO_IO07__LPUART6_RTS_B	0x31e>; /* WiFi_UART_SoC_RTS */
+	};
+
+	/* Verdin CTRL_SLEEP_MOCI# */
+	pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
+		fsl,pins = <IMX95_PAD_SAI1_RXD0__AONMIX_TOP_GPIO1_IO_BIT14	0x51e>; /* SODIMM 256 */
+	};
+
+	/* Verdin CTRL_WAKE1_MICO# */
+	pinctrl_ctrl_wake1_mico: ctrlwake1micogrp {
+		fsl,pins = <IMX95_PAD_PDM_BIT_STREAM1__AONMIX_TOP_GPIO1_IO_BIT10	0x31e>; /* SODIMM 252 */
+	};
+
+	/* Verdin CSI_1_MCLK */
+	pinctrl_csi1_mclk: csi1mclkgrp {
+		fsl,pins = <IMX95_PAD_CCM_CLKO1__CCMSRCGPCMIX_TOP_CLKO_1	0x51e>; /* SODIMM 91 */
+	};
+
+	/* Verdin ETH_2_RGMII_MDIO, shared between all ethernet ports */
+	pinctrl_emdio: emdiogrp {
+		fsl,pins = <IMX95_PAD_ENET2_MDC__NETCMIX_TOP_NETC_MDC	0x50e>, /* ENET2_MDC, SODIMM 193 */
+			   <IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_NETC_MDIO	0x90e>; /* ENET2_MDIO, SODIMM 191 */
+	};
+
+	/* Verdin ETH_1 (On-module PHY) */
+	pinctrl_enetc0: enetc0grp {
+		fsl,pins = <IMX95_PAD_ENET1_TX_CTL__NETCMIX_TOP_ETH0_RGMII_TX_CTL	0x57e>, /* ENET1_TX_CTL */
+			   <IMX95_PAD_ENET1_TXC__NETCMIX_TOP_ETH0_RGMII_TX_CLK		0x58e>, /* ENET1_TXC    */
+			   <IMX95_PAD_ENET1_TD0__NETCMIX_TOP_ETH0_RGMII_TD0		0x50e>, /* ENET1_TDO    */
+			   <IMX95_PAD_ENET1_TD1__NETCMIX_TOP_ETH0_RGMII_TD1		0x50e>, /* ENET1_TD1    */
+			   <IMX95_PAD_ENET1_TD2__NETCMIX_TOP_ETH0_RGMII_TD2		0x50e>, /* ENET1_TD2    */
+			   <IMX95_PAD_ENET1_TD3__NETCMIX_TOP_ETH0_RGMII_TD3		0x50e>, /* ENET1_TD3    */
+			   <IMX95_PAD_ENET1_RX_CTL__NETCMIX_TOP_ETH0_RGMII_RX_CTL	0x57e>, /* ENET1_RX_CTL */
+			   <IMX95_PAD_ENET1_RXC__NETCMIX_TOP_ETH0_RGMII_RX_CLK		0x58e>, /* ENET1_RXC    */
+			   <IMX95_PAD_ENET1_RD0__NETCMIX_TOP_ETH0_RGMII_RD0		0x57e>, /* ENET1_RD0    */
+			   <IMX95_PAD_ENET1_RD1__NETCMIX_TOP_ETH0_RGMII_RD1		0x57e>, /* ENET1_RD1    */
+			   <IMX95_PAD_ENET1_RD2__NETCMIX_TOP_ETH0_RGMII_RD2		0x57e>, /* ENET1_RD2    */
+			   <IMX95_PAD_ENET1_RD3__NETCMIX_TOP_ETH0_RGMII_RD3		0x57e>; /* ENET1_RD3    */
+	};
+
+	/* Verdin ETH_2_RGMII */
+	pinctrl_enetc1: enetc1grp {
+		fsl,pins = <IMX95_PAD_ENET2_TX_CTL__NETCMIX_TOP_ETH1_RGMII_TX_CTL	0x57e>, /* ENET2_TX_CTL */
+			   <IMX95_PAD_ENET2_TXC__NETCMIX_TOP_ETH1_RGMII_TX_CLK		0x58e>, /* ENET2_TXC    */
+			   <IMX95_PAD_ENET2_TD0__NETCMIX_TOP_ETH1_RGMII_TD0		0x50e>, /* ENET2_TD0    */
+			   <IMX95_PAD_ENET2_TD1__NETCMIX_TOP_ETH1_RGMII_TD1		0x50e>, /* ENET2_TD1    */
+			   <IMX95_PAD_ENET2_TD2__NETCMIX_TOP_ETH1_RGMII_TD2		0x50e>, /* ENET2_TD2    */
+			   <IMX95_PAD_ENET2_TD3__NETCMIX_TOP_ETH1_RGMII_TD3		0x50e>, /* ENET2_TD3    */
+			   <IMX95_PAD_ENET2_RX_CTL__NETCMIX_TOP_ETH1_RGMII_RX_CTL	0x57e>, /* ENET2_RX_CTL */
+			   <IMX95_PAD_ENET2_RXC__NETCMIX_TOP_ETH1_RGMII_RX_CLK		0x58e>, /* ENET2_RXC    */
+			   <IMX95_PAD_ENET2_RD0__NETCMIX_TOP_ETH1_RGMII_RD0		0x57e>, /* ENET2_RD0    */
+			   <IMX95_PAD_ENET2_RD1__NETCMIX_TOP_ETH1_RGMII_RD1		0x57e>, /* ENET2_RD1    */
+			   <IMX95_PAD_ENET2_RD2__NETCMIX_TOP_ETH1_RGMII_RD2		0x57e>, /* ENET2_RD2    */
+			   <IMX95_PAD_ENET2_RD3__NETCMIX_TOP_ETH1_RGMII_RD3		0x57e>; /* ENET2_RD3    */
+	};
+
+	/* Verdin ETH_2_RGMII_INT#  */
+	pinctrl_eth2_rgmii_int: eth2rgmiiintgrp {
+		fsl,pins = <IMX95_PAD_SAI1_TXC__AONMIX_TOP_GPIO1_IO_BIT12	0x31e>; /* SODIMM 189 */
+	};
+
+	/* Verdin CAN_1 */
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <IMX95_PAD_PDM_CLK__AONMIX_TOP_CAN1_TX		0x39e>, /* SODIMM 20 */
+			   <IMX95_PAD_PDM_BIT_STREAM0__AONMIX_TOP_CAN1_RX	0x39e>; /* SODIMM 22 */
+	};
+
+	/* Verdin CAN_2 */
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO25__CAN2_TX	0x39e>, /* SODIMM 24 */
+			   <IMX95_PAD_GPIO_IO27__CAN2_RX	0x39e>; /* SODIMM 26 */
+	};
+
+	/* Verdin GPIO_1 */
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO00__GPIO2_IO_BIT0	0x51e>; /* SODIMM 206 */
+	};
+
+	/* Verdin GPIO_2 */
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO18__GPIO2_IO_BIT18	0x51e>; /* SODIMM 208 */
+	};
+
+	/* Verdin GPIO_3 */
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO24__GPIO2_IO_BIT24	0x51e>; /* SODIMM 210 */
+	};
+
+	/* Verdin GPIO_4 */
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO32__GPIO5_IO_BIT12	0x51e>; /* SODIMM 212 */
+	};
+
+	/* Verdin GPIO_5_CSI */
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins = <IMX95_PAD_CCM_CLKO3__GPIO4_IO_BIT28	0x51e>; /* SODIMM 216 */
+	};
+
+	/* Verdin GPIO_6_CSI */
+	pinctrl_gpio6: gpio6grp {
+		fsl,pins = <IMX95_PAD_CCM_CLKO2__GPIO3_IO_BIT27	0x51e>; /* SODIMM 218 */
+	};
+
+	/* Verdin I2S_2_BCLK as GPIO (conflict with Verdin I2S_2) */
+	pinctrl_i2s_2_bclk_gpio: i2s2bclkgpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA6__GPIO5_IO_BIT6	0x51e>; /* SODIMM 42 */
+	};
+
+	/* Verdin I2S_2_D_IN as GPIO (conflict with Verdin I2S_2) */
+	pinctrl_i2s_2_d_in_gpio: i2s2dingpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA7__GPIO5_IO_BIT7	0x31e>; /* SODIMM 48 */
+	};
+
+	/* Verdin I2S_2_D_OUT as GPIO (conflict with Verdin I2S_2) */
+	pinctrl_i2s_2_d_out_gpio: i2s2doutgpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA4__GPIO5_IO_BIT4	0x51e>; /* SODIMM 46 */
+	};
+
+	/* Verdin I2S_2_SYNC as GPIO (conflict with Verdin I2S_2) */
+	pinctrl_i2s_2_sync_gpio: i2s2syncgpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA5__GPIO5_IO_BIT5	0x51e>; /* SODIMM 44 */
+	};
+
+	/* Verdin I2C_3_HDMI */
+	pinctrl_i3c2: i3c2cgrp {
+		fsl,pins = <IMX95_PAD_ENET1_MDC__I3C2_SCL	0x40001186>, /* SODIMM 59 */
+			   <IMX95_PAD_ENET1_MDIO__I3C2_SDA	0x40001186>; /* SODIMM 57 */
+	};
+
+	pinctrl_io_exp_int: ioexpintgrp {
+		fsl,pins = <IMX95_PAD_SAI1_TXD0__AONMIX_TOP_GPIO1_IO_BIT13	0x31e>; /* IO_EXP_INT */
+	};
+
+	/* CTRL_I2C (On-module I2C) */
+	pinctrl_lpi2c2: lpi2c2grp {
+		fsl,pins = <IMX95_PAD_I2C2_SCL__AONMIX_TOP_LPI2C2_SCL	0x40001b9e>, /* CTRL_I2C_SCL */
+			   <IMX95_PAD_I2C2_SDA__AONMIX_TOP_LPI2C2_SDA	0x40001b9e>; /* CTRL_I2C_SDA */
+	};
+
+	pinctrl_lpi2c2_gpio: lpi2c2gpiogrp {
+		fsl,pins = <IMX95_PAD_I2C2_SCL__AONMIX_TOP_GPIO1_IO_BIT2	0x40001b9e>, /* CTRL_I2C_SCL */
+			   <IMX95_PAD_I2C2_SDA__AONMIX_TOP_GPIO1_IO_BIT3	0x40001b9e>; /* CTRL_I2C_SDA */
+	};
+
+	/* Verdin I2C_2_DSI */
+	pinctrl_lpi2c3: lpi2c3grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO28__LPI2C3_SDA	0x40001b9e>, /* SODIMM 53 */
+			   <IMX95_PAD_GPIO_IO29__LPI2C3_SCL	0x40001b9e>; /* SODIMM 55 */
+	};
+
+	pinctrl_lpi2c3_gpio: lpi2c3gpiogrp {
+		fsl,pins = <IMX95_PAD_GPIO_IO28__GPIO2_IO_BIT28	0x40001b9e>, /* SODIMM 53 */
+			   <IMX95_PAD_GPIO_IO29__GPIO2_IO_BIT29	0x40001b9e>; /* SODIMM 55 */
+	};
+
+	/* Verdin I2C_1 */
+	pinctrl_lpi2c4: lpi2c4grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO31__LPI2C4_SCL	0x40001b9e>, /* SODIMM 14 */
+			   <IMX95_PAD_GPIO_IO30__LPI2C4_SDA	0x40001b9e>; /* SODIMM 12 */
+	};
+
+	pinctrl_lpi2c4_gpio: lpi2c4gpiogrp {
+		fsl,pins = <IMX95_PAD_GPIO_IO31__GPIO2_IO_BIT31	0x40001b9e>, /* SODIMM 14 */
+			   <IMX95_PAD_GPIO_IO30__GPIO2_IO_BIT30	0x40001b9e>; /* SODIMM 12 */
+	};
+
+	/* Verdin I2C_4_CSI */
+	pinctrl_lpi2c5: lpi2c5grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO22__LPI2C5_SDA	0x40001b9e>, /* SODIMM 93 */
+			   <IMX95_PAD_GPIO_IO23__LPI2C5_SCL	0x40001b9e>; /* SODIMM 95 */
+	};
+
+	pinctrl_lpi2c5_gpio: lpi2c5gpiogrp {
+		fsl,pins = <IMX95_PAD_GPIO_IO22__GPIO2_IO_BIT22	0x40001b9e>, /* SODIMM 93 */
+			   <IMX95_PAD_GPIO_IO23__GPIO2_IO_BIT23	0x40001b9e>; /* SODIMM 95 */
+	};
+
+	/* Verdin SPI_1 */
+	pinctrl_lpspi6: lpspi6grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO01__LPSPI6_SIN	0x3fe>, /* SODIMM 198 */
+			   <IMX95_PAD_GPIO_IO02__LPSPI6_SOUT	0x3fe>, /* SODIMM 200 */
+			   <IMX95_PAD_GPIO_IO03__LPSPI6_SCK	0x3fe>; /* SODIMM 196 */
+	};
+
+	/* Verdin QSPI_1_CLK as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_clk_gpio: qspi1clkgpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_SCLK__GPIO5_IO_BIT9		0x11e>; /* SODIMM 52 */
+	};
+
+	/* Verdin QSPI_1_CS# as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_cs_gpio: qspi1csgpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_SS0_B__GPIO5_IO_BIT10	0x11e>; /* SODIMM 54 */
+	};
+
+	/* Verdin QSPI_1_CS2# as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_cs2_gpio: qspi1cs2gpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_SS1_B__GPIO5_IO_BIT11	0x11e>; /* SODIMM 64 */
+	};
+
+	/* Verdin QSPI_1_DQS as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_dqs_gpio: qspi1dqsgpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DQS__GPIO5_IO_BIT8		0x11e>; /* SODIMM 66 */
+	};
+
+	/* Verdin QSPI_1_IO0 as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_io0_gpio: qspi1io0gpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA0__GPIO5_IO_BIT0	0x119e>; /* SODIMM 56 */
+	};
+
+	/* Verdin QSPI_1_IO1 as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_io1_gpio: qspi1io1gpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA1__GPIO5_IO_BIT1	0x119e>; /* SODIMM 58 */
+	};
+
+	/* Verdin QSPI_1_IO2 as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_io2_gpio: qspi1io2gpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA2__GPIO5_IO_BIT2	0x11e>; /* SODIMM 60 */
+	};
+
+	/* Verdin QSPI_1_IO3 as GPIO (conflict with Verdin QSPI_1 interface) */
+	pinctrl_qspi1_io3_gpio: qspi1io3gpiogrp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA3__GPIO5_IO_BIT3	0x11e>; /* SODIMM 62 */
+	};
+
+	/* Verdin SPI_1_CS */
+	pinctrl_spi1_cs: spi1csgrp {
+		fsl,pins = <IMX95_PAD_CCM_CLKO4__GPIO4_IO_BIT29	0x3fe>; /* SODIMM 202 */
+	};
+
+	/* Verdin I2S_1 */
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO16__SAI3_TX_BCLK		0x11e>, /* SODIMM 30 */
+			   <IMX95_PAD_GPIO_IO20__SAI3_RX_DATA_BIT0	0x11e>, /* SODIMM 36 */
+			   <IMX95_PAD_GPIO_IO21__SAI3_TX_DATA_BIT0	0x11e>, /* SODIMM 34 */
+			   <IMX95_PAD_GPIO_IO26__SAI3_TX_SYNC		0x11e>; /* SODIMM 32 */
+	};
+
+	/* Verdin I2S_1_MCLK */
+	pinctrl_sai3_mclk: sai3mclkgrp {
+		fsl,pins = <IMX95_PAD_GPIO_IO17__SAI3_MCLK	0x31e>; /* SODIMM 38 */
+	};
+
+	/* Verdin I2S_2 */
+	pinctrl_sai5: sai5grp {
+		fsl,pins = <IMX95_PAD_XSPI1_DATA4__SAI5_TX_DATA_BIT0	0x11e>, /* SODIMM 46 */
+			   <IMX95_PAD_XSPI1_DATA5__SAI5_TX_SYNC		0x11e>, /* SODIMM 44 */
+			   <IMX95_PAD_XSPI1_DATA6__SAI5_TX_BCLK		0x11e>, /* SODIMM 42 */
+			   <IMX95_PAD_XSPI1_DATA7__SAI5_RX_DATA_BIT0	0x11e>; /* SODIMM 48 */
+	};
+
+	/* Verdin PWM_1 */
+	pinctrl_tpm4: tpm4grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO05__TPM4_CH0	0x11e>; /* SODIMM 15 */
+	};
+
+	/* Verdin PWM_2 */
+	pinctrl_tpm5: tpm5grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO06__TPM5_CH0	0x11e>; /* SODIMM 16 */
+	};
+
+	/* Verdin PWM_3_DSI */
+	pinctrl_tpm6: tpm6grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO19__TPM6_CH2	0x11e>; /* SODIMM 19 */
+	};
+
+	/* Verdin PWM_3_DSI as GPIO */
+	pinctrl_tpm6_gpio: tpm6gpiogrp {
+		fsl,pins = <IMX95_PAD_GPIO_IO19__GPIO2_IO_BIT19	0x51e>; /* SODIMM 19 */
+	};
+
+	/* Verdin UART_3, used as the Linux Console */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <IMX95_PAD_UART1_RXD__AONMIX_TOP_LPUART1_RX	0x31e>, /* SODIMM 147 */
+			   <IMX95_PAD_UART1_TXD__AONMIX_TOP_LPUART1_TX	0x31e>; /* SODIMM 149 */
+	};
+
+	/* Verdin UART_4 */
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <IMX95_PAD_UART2_RXD__AONMIX_TOP_LPUART2_RX	0x31e>, /* SODIMM 151 */
+			   <IMX95_PAD_UART2_TXD__AONMIX_TOP_LPUART2_TX	0x31e>; /* SODIMM 153 */
+	};
+
+	/* Verdin UART_1 */
+	pinctrl_uart7: uart7grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO08__LPUART7_TX	0x31e>, /* SODIMM 131 */
+			   <IMX95_PAD_GPIO_IO09__LPUART7_RX	0x31e>, /* SODIMM 129 */
+			   <IMX95_PAD_GPIO_IO10__LPUART7_CTS_B	0x31e>, /* SODIMM 135 */
+			   <IMX95_PAD_GPIO_IO11__LPUART7_RTS_B	0x31e>; /* SODIMM 133 */
+	};
+
+	/* Verdin UART_2 */
+	pinctrl_uart8: uart8grp {
+		fsl,pins = <IMX95_PAD_GPIO_IO12__LPUART8_TX	0x31e>, /* SODIMM 139 */
+			   <IMX95_PAD_GPIO_IO13__LPUART8_RX	0x31e>, /* SODIMM 137 */
+			   <IMX95_PAD_GPIO_IO14__LPUART8_CTS_B	0x31e>, /* SODIMM 143 */
+			   <IMX95_PAD_GPIO_IO15__LPUART8_RTS_B	0x31e>; /* SODIMM 141 */
+	};
+
+	/* On-module eMMC */
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <IMX95_PAD_SD1_CLK__USDHC1_CLK	0x158e>, /* SD1_CLK    */
+			   <IMX95_PAD_SD1_CMD__USDHC1_CMD	0x138e>, /* SD1_CMD    */
+			   <IMX95_PAD_SD1_DATA0__USDHC1_DATA0	0x138e>, /* SD1_DATA0  */
+			   <IMX95_PAD_SD1_DATA1__USDHC1_DATA1	0x138e>, /* SD1_DATA1  */
+			   <IMX95_PAD_SD1_DATA2__USDHC1_DATA2	0x138e>, /* SD1_DATA2  */
+			   <IMX95_PAD_SD1_DATA3__USDHC1_DATA3	0x138e>, /* SD1_DATA3  */
+			   <IMX95_PAD_SD1_DATA4__USDHC1_DATA4	0x138e>, /* SD1_DATA4  */
+			   <IMX95_PAD_SD1_DATA5__USDHC1_DATA5	0x138e>, /* SD1_DATA5  */
+			   <IMX95_PAD_SD1_DATA6__USDHC1_DATA6	0x138e>, /* SD1_DATA6  */
+			   <IMX95_PAD_SD1_DATA7__USDHC1_DATA7	0x138e>, /* SD1_DATA7  */
+			   <IMX95_PAD_SD1_STROBE__USDHC1_STROBE	0x158e>; /* SD1_STROBE */
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <IMX95_PAD_SD1_CLK__USDHC1_CLK	0x15fe>, /* SD1_CLK    */
+			   <IMX95_PAD_SD1_CMD__USDHC1_CMD	0x13fe>, /* SD1_CMD    */
+			   <IMX95_PAD_SD1_DATA0__USDHC1_DATA0	0x13fe>, /* SD1_DATA0  */
+			   <IMX95_PAD_SD1_DATA1__USDHC1_DATA1	0x13fe>, /* SD1_DATA1  */
+			   <IMX95_PAD_SD1_DATA2__USDHC1_DATA2	0x13fe>, /* SD1_DATA2  */
+			   <IMX95_PAD_SD1_DATA3__USDHC1_DATA3	0x13fe>, /* SD1_DATA3  */
+			   <IMX95_PAD_SD1_DATA4__USDHC1_DATA4	0x13fe>, /* SD1_DATA4  */
+			   <IMX95_PAD_SD1_DATA5__USDHC1_DATA5	0x13fe>, /* SD1_DATA5  */
+			   <IMX95_PAD_SD1_DATA6__USDHC1_DATA6	0x13fe>, /* SD1_DATA6  */
+			   <IMX95_PAD_SD1_DATA7__USDHC1_DATA7	0x13fe>, /* SD1_DATA7  */
+			   <IMX95_PAD_SD1_STROBE__USDHC1_STROBE	0x15fe>; /* SD1_STROBE */
+	};
+
+	/* Verdin SD_1 */
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <IMX95_PAD_SD2_CLK__USDHC2_CLK	0x158e>, /* SODIMM 78 */
+			   <IMX95_PAD_SD2_CMD__USDHC2_CMD	0x138e>, /* SODIMM 74 */
+			   <IMX95_PAD_SD2_DATA0__USDHC2_DATA0	0x138e>, /* SODIMM 80 */
+			   <IMX95_PAD_SD2_DATA1__USDHC2_DATA1	0x138e>, /* SODIMM 82 */
+			   <IMX95_PAD_SD2_DATA2__USDHC2_DATA2	0x138e>, /* SODIMM 70 */
+			   <IMX95_PAD_SD2_DATA3__USDHC2_DATA3	0x138e>; /* SODIMM 72 */
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <IMX95_PAD_SD2_CLK__USDHC2_CLK	0x15fe>, /* SODIMM 78 */
+			   <IMX95_PAD_SD2_CMD__USDHC2_CMD	0x13fe>, /* SODIMM 74 */
+			   <IMX95_PAD_SD2_DATA0__USDHC2_DATA0	0x13fe>, /* SODIMM 80 */
+			   <IMX95_PAD_SD2_DATA1__USDHC2_DATA1	0x13fe>, /* SODIMM 82 */
+			   <IMX95_PAD_SD2_DATA2__USDHC2_DATA2	0x13fe>, /* SODIMM 70 */
+			   <IMX95_PAD_SD2_DATA3__USDHC2_DATA3	0x13fe>; /* SODIMM 72 */
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-sleepgrp {
+		fsl,pins = <IMX95_PAD_SD2_CLK__USDHC2_CLK	0x400>, /* SODIMM 78 */
+			   <IMX95_PAD_SD2_CMD__USDHC2_CMD	0x400>, /* SODIMM 74 */
+			   <IMX95_PAD_SD2_DATA0__USDHC2_DATA0	0x400>, /* SODIMM 80 */
+			   <IMX95_PAD_SD2_DATA1__USDHC2_DATA1	0x400>, /* SODIMM 82 */
+			   <IMX95_PAD_SD2_DATA2__USDHC2_DATA2	0x400>, /* SODIMM 70 */
+			   <IMX95_PAD_SD2_DATA3__USDHC2_DATA3	0x400>; /* SODIMM 72 */
+	};
+
+	/* Verdin SD_1_CD# */
+	pinctrl_usdhc2_cd: usdhc2-cdgrp {
+		fsl,pins = <IMX95_PAD_SD2_CD_B__GPIO3_IO_BIT0	0x1100>; /* SODIMM 84 */
+	};
+
+	/* Verdin SD_1_PWR_EN */
+	pinctrl_usdhc2_pwr_en: usdhc2-pwrengrp {
+		fsl,pins = <IMX95_PAD_SD2_RESET_B__GPIO3_IO_BIT7	0x11e>; /* SODIMM 76 */
+	};
+
+	pinctrl_usdhc2_vsel: usdhc2-vselgrp {
+		fsl,pins = <IMX95_PAD_SD2_VSELECT__GPIO3_IO_BIT19	0x4>; /* PMIC_SD2_VSEL */
+	};
+
+	/* On-module Wi-Fi on WB SKUs, module-specific SDIO otherwise */
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <IMX95_PAD_SD3_CLK__USDHC3_CLK	0x158e>, /* SD3_CLK   */
+			   <IMX95_PAD_SD3_CMD__USDHC3_CMD	0x138e>, /* SD3_CMD   */
+			   <IMX95_PAD_SD3_DATA0__USDHC3_DATA0	0x138e>, /* SD3_DATA0 */
+			   <IMX95_PAD_SD3_DATA1__USDHC3_DATA1	0x138e>, /* SD3_DATA1 */
+			   <IMX95_PAD_SD3_DATA2__USDHC3_DATA2	0x138e>, /* SD3_DATA2 */
+			   <IMX95_PAD_SD3_DATA3__USDHC3_DATA3	0x138e>; /* SD3_DATA3 */
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <IMX95_PAD_SD3_CLK__USDHC3_CLK	0x15fe>, /* SD3_CLK   */
+			   <IMX95_PAD_SD3_CMD__USDHC3_CMD	0x13fe>, /* SD3_CMD   */
+			   <IMX95_PAD_SD3_DATA0__USDHC3_DATA0	0x13fe>, /* SD3_DATA1 */
+			   <IMX95_PAD_SD3_DATA1__USDHC3_DATA1	0x13fe>, /* SD3_DATA2 */
+			   <IMX95_PAD_SD3_DATA2__USDHC3_DATA2	0x13fe>, /* SD3_DATA3 */
+			   <IMX95_PAD_SD3_DATA3__USDHC3_DATA3	0x13fe>; /* SD3_DATA4 */
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins = <IMX95_PAD_SAI1_TXFS__AONMIX_TOP_GPIO1_IO_BIT11	0x51e>; /* PMIC_EN_WIFI */
+	};
+
+	/* Verdin QSPI_1 */
+	pinctrl_flexspi1: flexspi1grp {
+		fsl,pins = <IMX95_PAD_XSPI1_SS0_B__FLEXSPI1_A_SS0_B	0x3fe>, /* SODIMM 54 */
+			   <IMX95_PAD_XSPI1_SS1_B__FLEXSPI1_A_SS1_B	0x3fe>, /* SODIMM 64 */
+			   <IMX95_PAD_XSPI1_SCLK__XSPI_CLK		0x3fe>, /* SODIMM 52 */
+			   <IMX95_PAD_XSPI1_DATA0__XSPI_DATA_BIT0	0x3fe>, /* SODIMM 56 */
+			   <IMX95_PAD_XSPI1_DATA1__XSPI_DATA_BIT1	0x3fe>, /* SODIMM 58 */
+			   <IMX95_PAD_XSPI1_DATA2__XSPI_DATA_BIT2	0x3fe>, /* SODIMM 60 */
+			   <IMX95_PAD_XSPI1_DATA3__XSPI_DATA_BIT3	0x3fe>, /* SODIMM 62 */
+			   <IMX95_PAD_XSPI1_DQS__XSPI_DQS		0x3fe>; /* SODIMM 66 */
+	};
+};

-- 
2.43.0