Re: [PATCH v8 8/9] arm64: dts: imx943-evk: Add display support using IT6263

[Liu Ying]

On Wed, Mar 04, 2026 at 11:34:17AM +0000, Laurentiu Palcu wrote:
> The ITE IT6263 based NXP LVDS to HDMI converter can be attached to the
> i.MX943 EVK board LVDS port using the mini-SAS connector. Since this is

Since the LVDS to HDMI converter can be attached or detached to the EVK
board, it would be appropriate to use a DT overlay instead?

> the default configuration for the EVK, add support for it here.
> 
> Signed-off-by: Laurentiu Palcu <laurentiu.palcu@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/freescale/imx943-evk.dts | 86 ++++++++++++++++++++++++++++
>  1 file changed, 86 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx943-evk.dts b/arch/arm64/boot/dts/freescale/imx943-evk.dts
> index c8ceabe3d9239..0b69450566159 100644
> --- a/arch/arm64/boot/dts/freescale/imx943-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx943-evk.dts
> @@ -55,6 +55,36 @@ dmic: dmic {
>  		#sound-dai-cells = <0>;
>  	};
>  
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		label = "hdmi";
> +		type = "a";
> +
> +		port {
> +			hdmi_connector_in: endpoint {
> +				remote-endpoint = <&it6263_out>;
> +			};
> +		};
> +	};
> +
> +	reg_1v8_ext: regulator-1v8-ext {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1V8_EXT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	reg_3v3_ext: regulator-3v3-ext {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3V3_EXT";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
>  	reg_m2_pwr: regulator-m2-pwr {
>  		compatible = "regulator-fixed";
>  		regulator-name = "M.2-power";
> @@ -179,6 +209,10 @@ memory@80000000 {
>  	};
>  };
>  
> +&dcif {
> +	status = "okay";
> +};
> +
>  &enetc1 {
>  	clocks = <&scmi_clk IMX94_CLK_MAC4>;
>  	clock-names = "ref";
> @@ -217,6 +251,21 @@ &flexcan4 {
>  	status = "okay";
>  };
>  
> +&ldb {
> +	assigned-clocks = <&scmi_clk IMX94_CLK_LDBPLL_VCO>,
> +			  <&scmi_clk IMX94_CLK_LDBPLL>;
> +	assigned-clock-rates = <4158000000>, <1039500000>;
> +	status = "okay";
> +
> +	ports {
> +		port@1 {
> +			lvds_out: endpoint {
> +				remote-endpoint = <&it6263_in>;
> +			};
> +		};
> +	};
> +};
> +
>  &lpi2c3 {
>  	clock-frequency = <400000>;
>  	pinctrl-0 = <&pinctrl_lpi2c3>;
> @@ -258,6 +307,43 @@ i2c@3 {
>  			reg = <3>;
>  			#address-cells = <1>;
>  			#size-cells = <0>;
> +
> +			lvds-to-hdmi-bridge@4c {

Maybe, change the node name to be "hdmi" to align with the nodes in
imx8mp-evk-lvds{0,1}-imx-lvds-hdmi-common.dtsi.

> +				compatible = "ite,it6263";
> +				reg = <0x4c>;
> +				data-mapping = "jeida-24";
> +				reset-gpios = <&pcal6416_i2c3_u171 8 GPIO_ACTIVE_HIGH>;
> +				ivdd-supply = <&reg_1v8_ext>;
> +				ovdd-supply = <&reg_3v3_ext>;
> +				txavcc18-supply = <&reg_1v8_ext>;
> +				txavcc33-supply = <&reg_3v3_ext>;
> +				pvcc1-supply = <&reg_1v8_ext>;
> +				pvcc2-supply = <&reg_1v8_ext>;
> +				avcc-supply = <&reg_3v3_ext>;
> +				anvdd-supply = <&reg_1v8_ext>;
> +				apvdd-supply = <&reg_1v8_ext>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +
> +						it6263_in: endpoint {
> +							remote-endpoint = <&lvds_out>;
> +						};
> +					};
> +
> +					port@2 {
> +						reg = <2>;
> +
> +						it6263_out: endpoint {
> +							remote-endpoint = <&hdmi_connector_in>;
> +						};
> +					};
> +				};
> +			};
>  		};
>  
>  		i2c@4 {
> 

-- 
Regards,
Liu Ying