Re: [PATCH v2 3/3] input: touchscreen: st1232: add system wakeup support

[Krzysztof Kozlowski]

On 06/03/2026 11:40, phucduc.bui@xxxxxxxxx wrote:
> From: bui duc phuc <phucduc.bui@xxxxxxxxx>
> 
> The ST1232 touchscreen controller can generate an interrupt when the
> panel is touched, which may be used as a wakeup source for the system.
> 
> Add support for system wakeup by initializing the device wakeup
> capability in probe() based on the "wakeup-source" device property.
> When wakeup is enabled, the driver enables IRQ wake during suspend
> so that touch events can wake the system.
> 
> Additionally, report wakeup events from the interrupt handler when
> the device is allowed to wake the system. This allows the PM core to
> track touch-generated wakeup events and helps avoid potential races
> with system suspend.
> 
> If wakeup is not enabled, the driver retains the existing behavior of
> disabling the IRQ and powering down the controller during suspend.
> 
> Signed-off-by: bui duc phuc <phucduc.bui@xxxxxxxxx>
> ---
>  drivers/input/touchscreen/st1232.c | 27 ++++++++++++++++++++++-----
>  1 file changed, 22 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/input/touchscreen/st1232.c b/drivers/input/touchscreen/st1232.c
> index 9b3901eec0a5..2bab06cf099b 100644
> --- a/drivers/input/touchscreen/st1232.c
> +++ b/drivers/input/touchscreen/st1232.c
> @@ -183,6 +183,9 @@ static irqreturn_t st1232_ts_irq_handler(int irq, void *dev_id)
>  	int count;
>  	int error;
>  
> +	if (device_may_wakeup(&ts->client->dev))
> +		pm_wakeup_event(&ts->client->dev, 0);
> +
>  	error = st1232_ts_read_data(ts, REG_XY_COORDINATES, ts->read_buf_len);
>  	if (error)
>  		goto out;
> @@ -356,6 +359,9 @@ static int st1232_ts_probe(struct i2c_client *client)
>  
>  	i2c_set_clientdata(client, ts);
>  
> +	device_init_wakeup(&client->dev,
> +			device_property_read_bool(&client->dev, "wakeup-source"));
> +
>  	return 0;
>  }
>  
> @@ -363,11 +369,20 @@ static int st1232_ts_suspend(struct device *dev)
>  {
>  	struct i2c_client *client = to_i2c_client(dev);
>  	struct st1232_ts_data *ts = i2c_get_clientdata(client);
> +	int ret;
>  
> -	disable_irq(client->irq);
> +	dev_info(dev, "st1232: suspend called\n");
> +	dev_info(dev, "st1232: irq=%d wakeup=%d\n", client->irq, device_may_wakeup(dev));

No, there is no need to add success messages.

>  
> -	if (!device_may_wakeup(&client->dev))
> +	if (device_may_wakeup(dev)) {
> +		ret = enable_irq_wake(client->irq);
> +		dev_info(dev, "st1232: Supend use wakeup\n");
> +		dev_info(dev, "enable_irq_wake ret=%d\n", ret);

Drop both


> +	} else {
> +		dev_info(dev, "st1232: Suspend Don't use wakeup\n");

Drop



Best regards,
Krzysztof