[PATCH v1] PCI: mediatek-gen3: Align PERST# sequence with PCIe CEM specification

[Jian Yang]

Fix the control sequence of PERST# during system bootup/shutdown to
meet the requirement from PCIe CEM specification. There are two major
changes in this patch:

1. Some of MediaTek's chip will stop generating REFCLK if the
PCIE_PHY_RSTB signal of PCIe controller is asserted. We have to
adjust the startup sequence as follows to ensure that PERST# will be
de-asserted after the REFCLK is stable:
Assert PHY reset and PERST# -> delay 10ms -> De-assert PHY reset ->
delay 100ms -> De-assert PERST#

2. Add 'shutdown' callback to control the timing of PERST# and power
during the system shutdown phase, ensuring that PERST# is active
before the power on connector is removed.

Signed-off-by: Jian Yang <jian.yang@xxxxxxxxxxxx>
---
 drivers/pci/controller/pcie-mediatek-gen3.c | 39 +++++++++++++++++++--
 1 file changed, 36 insertions(+), 3 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
index a94fdbaf47fe..66d177918565 100644
--- a/drivers/pci/controller/pcie-mediatek-gen3.c
+++ b/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -62,6 +62,7 @@
 #define PCIE_PHY_RSTB			BIT(1)
 #define PCIE_BRG_RSTB			BIT(2)
 #define PCIE_PE_RSTB			BIT(3)
+#define PCIE_BRG_RST_RDY_MS		10
 
 #define PCIE_LTSSM_STATUS_REG		0x150
 #define PCIE_LTSSM_STATE_MASK		GENMASK(28, 24)
@@ -133,6 +134,7 @@
 #define MAX_NUM_PHY_RESETS		3
 
 #define PCIE_MTK_RESET_TIME_US		10
+#define PCIE_MTK_PDN_PERST_TIME_MS	5
 
 /* Time in ms needed to complete PCIe reset on EN7581 SoC */
 #define PCIE_EN7581_RESET_TIME_MS	100
@@ -430,6 +432,21 @@ static int mtk_pcie_devices_power_up(struct mtk_gen3_pcie *pcie)
 		return err;
 	}
 
+	/*
+	 * Some of MediaTek's chips won't output REFCLK when PCIE_PHY_RSTB is
+	 * asserted, we have to de-assert MAC & PHY & BRG reset signals first
+	 * to allow the REFCLK to be stable. While PCIE_BRG_RSTB is asserted,
+	 * there is a short period during which the PCIe internal register
+	 * cannot be accessed, so we need to wait 10ms here.
+	 */
+	msleep(PCIE_BRG_RST_RDY_MS);
+
+	if (!(pcie->soc->flags & SKIP_PCIE_RSTB)) {
+		/* De-assert MAC, PHY and BRG reset signals */
+		val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB);
+		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
+	}
+
 	/*
 	 * Described in PCIe CEM specification revision 6.0.
 	 *
@@ -439,9 +456,8 @@ static int mtk_pcie_devices_power_up(struct mtk_gen3_pcie *pcie)
 	msleep(PCIE_T_PVPERL_MS);
 
 	if (!(pcie->soc->flags & SKIP_PCIE_RSTB)) {
-		/* De-assert reset signals */
-		val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB |
-			 PCIE_PE_RSTB);
+		/* De-assert PERST# signal */
+		val &= ~PCIE_PE_RSTB;
 		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
 	}
 
@@ -459,6 +475,14 @@ static void mtk_pcie_devices_power_down(struct mtk_gen3_pcie *pcie)
 		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
 	}
 
+	/*
+	 * Described in PCIe CEM specification revision 6.0.
+	 *
+	 * The PERST# gose active before the power on the connector is removed.
+	 * Wait a while to ensure the voltage transition of PERST# is completed.
+	 */
+	msleep(PCIE_MTK_PDN_PERST_TIME_MS);
+
 	pci_pwrctrl_power_off_devices(pcie->dev);
 }
 
@@ -1266,6 +1290,14 @@ static void mtk_pcie_remove(struct platform_device *pdev)
 	mtk_pcie_irq_teardown(pcie);
 }
 
+static void mtk_pcie_shutdown(struct platform_device *pdev)
+{
+	struct mtk_gen3_pcie *pcie = platform_get_drvdata(pdev);
+
+	mtk_pcie_devices_power_down(pcie);
+	mtk_pcie_power_down(pcie);
+}
+
 static void mtk_pcie_irq_save(struct mtk_gen3_pcie *pcie)
 {
 	int i;
@@ -1404,6 +1436,7 @@ MODULE_DEVICE_TABLE(of, mtk_pcie_of_match);
 static struct platform_driver mtk_pcie_driver = {
 	.probe = mtk_pcie_probe,
 	.remove = mtk_pcie_remove,
+	.shutdown = mtk_pcie_shutdown,
 	.driver = {
 		.name = "mtk-pcie-gen3",
 		.of_match_table = mtk_pcie_of_match,
-- 
2.45.2