Re: [PATCH 3/3] drm: lcdif: Wait for vblank before disabling DMA

[Paul Kocialkowski]

Hi Lucas,

On Tue 31 Mar 26, 11:14, Lucas Stach wrote:
> Am Dienstag, dem 31.03.2026 um 00:46 +0200 schrieb Paul Kocialkowski:
> > It is necessary to wait for the full frame to finish streaming
> > through the DMA engine before we can safely disable it by removing
> > the DISP_PARA_DISP_ON bit. Disabling it in-flight can leave the
> > hardware confused and unable to resume streaming for the next frame.
> > 
> > This causes the FIFO underrun and empty status bits to be set and
> > a single solid color to be shown on the display, coming from one of
> > the pixels of the previous frame. The issue occurs sporadically when
> > a new mode is set, which triggers the crtc disable and enable paths.
> > 
> > Setting the shadow load bit and waiting for it to be cleared by the
> > DMA engine allows waiting for completion.
> > 
> > The NXP BSP driver addresses this issue with a hardcoded 25 ms sleep.
> > 
> > Fixes: 9db35bb349a0 ("drm: lcdif: Add support for i.MX8MP LCDIF variant")
> > Signed-off-by: Paul Kocialkowski <paulk@xxxxxxxxxxx>
> > Co-developed-by: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> > ---
> >  drivers/gpu/drm/mxsfb/lcdif_kms.c | 16 ++++++++++++++++
> >  1 file changed, 16 insertions(+)
> > 
> > diff --git a/drivers/gpu/drm/mxsfb/lcdif_kms.c b/drivers/gpu/drm/mxsfb/lcdif_kms.c
> > index 1aac354041c7..7dce7f48d938 100644
> > --- a/drivers/gpu/drm/mxsfb/lcdif_kms.c
> > +++ b/drivers/gpu/drm/mxsfb/lcdif_kms.c
> > @@ -393,6 +393,22 @@ static void lcdif_disable_controller(struct lcdif_drm_private *lcdif)
> >  	if (ret)
> >  		drm_err(lcdif->drm, "Failed to disable controller!\n");
> >  
> You can drop this no-op poll above...

You're right, it looks a bit weird to keep it as it's not needed.

> > +	/*
> > +	 * It is necessary to wait for the full frame to finish streaming
> > +	 * through the DMA engine before we can safely disable it by removing
> > +	 * the DISP_PARA_DISP_ON bit. Disabling it in-flight can leave the
> > +	 * hardware confused and unable to resume streaming for the next frame.
> > +	 */
> > +	reg = readl(lcdif->base + LCDC_V8_CTRLDESCL0_5);
> > +	reg |= CTRLDESCL0_5_SHADOW_LOAD_EN;
> > +	writel(reg, lcdif->base + LCDC_V8_CTRLDESCL0_5);
> > +
> .. then setting the shadow load enable bit can be merged with the
> access clearing the DMA enable bit.

I've just tried it out and it works just as well!

> > +	ret = readl_poll_timeout(lcdif->base + LCDC_V8_CTRLDESCL0_5,
> > +				 reg, !(reg & CTRLDESCL0_5_SHADOW_LOAD_EN),
> > +				 0, 36000);	/* Wait ~2 frame times max */
> 
> I know this is just a copy from the existing poll, but I don't think
> the busy looping makes a lot of sense. I guess relaxing the poll by a
> 100us or even 200us wait between checks wouldn't hurt.

Yeah good point too. I think 200 us is definitely fine since we're looking
at an average wait of a few ms.

Will respin the series then!

Thanks for the review,

Paul

> > +	if (ret)
> > +		drm_err(lcdif->drm, "Failed to disable controller!\n");
> > +
> >  	reg = readl(lcdif->base + LCDC_V8_DISP_PARA);
> >  	reg &= ~DISP_PARA_DISP_ON;
> >  	writel(reg, lcdif->base + LCDC_V8_DISP_PARA);
> 

-- 
Paul Kocialkowski,

Independent contractor - sys-base - https://www.sys-base.io/
Free software developer - https://www.paulk.fr/

Expert in multimedia, graphics and embedded hardware support with Linux.

Attachment: signature.asc
Description: PGP signature