[PATCH v2 1/2] arm64: dts: qcom: sdm845-google: Add dual front IMX355 cameras
From: David Heidelberg via B4 Relay
Date: Sat Apr 11 2026 - 06:12:52 EST
From: David Heidelberg <david@xxxxxxx>
The Pixel 3 features two front-facing Sony IMX355 sensors with
different focal lengths (standard and wide-angle).
Both sensors are connected via CSIPHY1 and controlled over CCI I2C1,
using MCLK2 as the clock source. Describe the camera nodes and
associated resources in the device tree.
This enables support for the dual front camera configuration.
Signed-off-by: David Heidelberg <david@xxxxxxx>
---
arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi | 187 ++++++++++++++++++++-
1 file changed, 186 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi
index 6930066857768..084058a597c10 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi
@@ -6,6 +6,7 @@
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/media/video-interfaces.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sdm845.dtsi"
@@ -132,6 +133,38 @@ vreg_s4a_1p8: regulator-vreg-s4a-1p8 {
vin-supply = <&vph_pwr>;
};
+ camera_front_avdd: front-cam-avdd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "front_cam_avdd";
+
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&cam_front_avdd_default_pin>;
+ pinctrl-names = "default";
+
+ vin-supply = <&vreg_bob>;
+ };
+
+ camera_front_aux_avdd: front-cam-aux-avdd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "front_cam_aux_avdd";
+
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ gpios = <&tlmm 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&cam_front_aux_avdd_default_pin>;
+ pinctrl-names = "default";
+
+ vin-supply = <&vreg_bob>;
+ };
+
wcn3990-pmu {
compatible = "qcom,wcn3990-pmu";
@@ -214,6 +247,9 @@ vreg_s7a_1p025: smps7 {
regulator-max-microvolt = <1028000>;
};
+ vdda_mipi_csi0_0p9:
+ vdda_mipi_csi1_0p9:
+ vdda_mipi_csi2_0p9:
vdda_mipi_dsi0_pll:
vreg_l1a_0p875: ldo1 {
regulator-min-microvolt = <880000>;
@@ -288,6 +324,13 @@ vreg_l21a_2p95: ldo21 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
+ vreg_l22a_3p3: ldo22 {
+ regulator-min-microvolt = <2864000>;
+ regulator-max-microvolt = <2864000>;
+
+ regulator-boot-on;
+ };
+
vreg_l24a_3p075: ldo24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
@@ -319,6 +362,12 @@ vreg_l28a_3p0: ldo28 {
*/
regulator-always-on;
};
+
+ cam_vio_1p8:
+ vreg_lvs1_1p8: lvs1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
};
regulators-1 {
@@ -351,6 +400,45 @@ vreg_s3c_0p6: smps3 {
};
};
+&camss {
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l26a_1p2>;
+
+ vdda-csi0-supply = <&vdda_mipi_csi0_0p9>;
+ vdda-csi1-supply = <&vdda_mipi_csi1_0p9>;
+ vdda-csi2-supply = <&vdda_mipi_csi2_0p9>;
+
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ camss_endpoint1: endpoint {
+ bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&cam_aux_front_endpoint>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ camss_endpoint2: endpoint {
+ bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&cam_front_endpoint>;
+ };
+ };
+ };
+};
+
+&cci0_sleep {
+ /* bus has external pull-up, don't pull down */
+ bias-disable;
+};
+
&cci {
status = "okay";
};
@@ -358,7 +446,72 @@ &cci {
&cci_i2c1 {
/* actuator @0c */
- /* front camera, imx355 @1a */
+ front_cam: camera@10 {
+ compatible = "sony,imx355";
+ reg = <0x10>;
+
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ assigned-clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ /*
+ * The sensor can accept a 24 MHz clock, but 19.2 MHz has
+ * better driver compatibility.
+ */
+ assigned-clock-rates = <19200000>;
+
+ reset-gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
+
+ avdd-supply = <&camera_front_avdd>;
+ dvdd-supply = <&vreg_s3a_1p35>;
+ dovdd-supply = <&cam_vio_1p8>;
+
+ /* MCLK2 pin (gpio15) is claimed by the aux sensor */
+ pinctrl-0 = <&cam_front_reset_default_pin>;
+ pinctrl-names = "default";
+
+ rotation = <270>;
+ orientation = <0>;
+
+ port {
+ cam_front_endpoint: endpoint {
+ data-lanes = <1 2 3 4>;
+ link-frequencies = /bits/ 64 <360000000>;
+ remote-endpoint = <&camss_endpoint2>;
+ };
+ };
+ };
+
+ front_aux_cam: camera@1a {
+ compatible = "sony,imx355";
+ reg = <0x1a>;
+
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ assigned-clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ /*
+ * The sensor can accept a 24 MHz clock, but 19.2 MHz has
+ * better driver compatibility.
+ */
+ assigned-clock-rates = <19200000>;
+
+ reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+
+ avdd-supply = <&camera_front_aux_avdd>;
+ dvdd-supply = <&vreg_s3a_1p35>;
+ dovdd-supply = <&cam_vio_1p8>;
+
+ pinctrl-0 = <&cam_mclk2_default &cam_front_aux_reset_default_pin>;
+ pinctrl-names = "default";
+
+ rotation = <270>;
+ orientation = <0>;
+
+ port {
+ cam_aux_front_endpoint: endpoint {
+ data-lanes = <1 2 3 4>;
+ link-frequencies = /bits/ 64 <360000000>;
+ remote-endpoint = <&camss_endpoint1>;
+ };
+ };
+ };
/* eeprom @50, at24 driver says 8K */
};
@@ -459,6 +612,38 @@ &tlmm {
gpio-reserved-ranges = < 0 4>, /* SPI (Intel MNH Pixel Visual Core) */
<81 4>; /* SPI (most likely Fingerprint Cards FPC1075) */
+ cam_front_avdd_default_pin: cam-avdd-default-pins {
+ pins = "gpio8";
+ function = "gpio";
+
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cam_front_aux_reset_default_pin: cam-front-aux-reset-default-pins {
+ pins = "gpio9";
+ function = "gpio";
+
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cam_front_aux_avdd_default_pin: cam-avdd-aux-default-pins {
+ pins = "gpio14";
+ function = "gpio";
+
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cam_front_reset_default_pin: cam-front-reset-default-pins {
+ pins = "gpio21";
+ function = "gpio";
+
+ bias-disable;
+ drive-strength = <2>;
+ };
+
touchscreen_reset: ts-reset-state {
pins = "gpio99";
function = "gpio";
--
2.53.0