[PATCH v3 5/7] ata: libata-scsi: probe additional LUNs for multi-LUN ATAPI devices

[Phil Pemberton]

After LUN 0 is added for an ATAPI device, check its BLIST_FORCELUN
flag.  If set, call scsi_scan_target() with SCAN_WILD_CARD to trigger
the SCSI layer's built-in sequential LUN scan for that target only.
This probes LUNs 1..shost->max_lun, driven by the atapi_max_lun module
parameter from patch 1/6.  Devices without BLIST_FORCELUN (the vast
majority of ATAPI devices) are left with only LUN 0 -- no sequential
scan is triggered, so single-LUN devices like the iHAS124 DVD writer
are completely unaffected.

Non-responding LUNs (PQ=0/PDT=0x1f) are silently skipped by
scsi_probe_and_add_lun() when BLIST_NO_LUN_1F is set on the device
via scsi_devinfo (see patch 4/6).

Signed-off-by: Phil Pemberton <philpem@xxxxxxxxxxxxx>
---
 drivers/ata/libata-scsi.c | 37 ++++++++++++++++++++++++++++---------
 1 file changed, 28 insertions(+), 9 deletions(-)

diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 48c7d323d6f9..fc719e3d7d60 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -26,6 +26,7 @@
 #include <scsi/scsi_device.h>
 #include <scsi/scsi_tcq.h>
 #include <scsi/scsi_transport.h>
+#include <scsi/scsi_devinfo.h>
 #include <linux/libata.h>
 #include <linux/hdreg.h>
 #include <linux/uaccess.h>
@@ -4700,7 +4701,6 @@ void ata_scsi_scan_host(struct ata_port *ap, int sync)
  repeat:
 	ata_for_each_link(link, ap, EDGE) {
 		ata_for_each_dev(dev, link, ENABLED) {
-			struct scsi_device *sdev;
 			int channel = 0, id = 0;
 
 			if (dev->sdev[0])
@@ -4711,15 +4711,34 @@ void ata_scsi_scan_host(struct ata_port *ap, int sync)
 			else
 				channel = link->pmp;
 
-			sdev = __scsi_add_device(ap->scsi_host, channel, id, 0,
-						 NULL);
-			if (!IS_ERR(sdev)) {
-				dev->sdev[0] = sdev;
-				ata_scsi_assign_ofnode(dev, ap);
-				scsi_device_put(sdev);
-			} else {
-				dev->sdev[0] = NULL;
+			{
+				struct scsi_device *sdev;
+
+				sdev = __scsi_add_device(ap->scsi_host,
+							 channel, id, 0, NULL);
+				if (!IS_ERR(sdev)) {
+					/*
+					 * For multi-LUN ATAPI (BLIST_FORCELUN),
+					 * trigger the sequential LUN scan.
+					 * pdt_1f_for_no_lun (set during LUN 0
+					 * configure) ensures non-responding LUNs
+					 * are silently skipped.  dev->sdev[] is
+					 * populated by ata_scsi_dev_config()
+					 * during the scan callbacks.
+					 */
+					if (dev->class == ATA_DEV_ATAPI &&
+					    sdev->sdev_bflags & BLIST_FORCELUN)
+						scsi_scan_target(
+							&ap->scsi_host->shost_gendev,
+							channel, id,
+							SCAN_WILD_CARD,
+							SCSI_SCAN_RESCAN);
+					scsi_device_put(sdev);
+				}
 			}
+
+			if (dev->sdev[0])
+				ata_scsi_assign_ofnode(dev, ap);
 		}
 	}
 
-- 
2.43.0