[PATCH v1 02/12] arm64: dts: imx8mp-var-som-symphony: enable USB support

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r@xxxxxxxxxxxxx>

Enable the USB controllers on the Symphony carrier board.

Add the PTN5150 Type-C controller for USB role switching, enable the USB3
PHYs and controllers, configure the I2C bus used by the Type-C
controller, and set the first USB port in OTG mode and the second port
in host mode.

Signed-off-by: Stefano Radaelli <stefano.r@xxxxxxxxxxxxx>
---
 .../dts/freescale/imx8mp-var-som-symphony.dts | 80 ++++++++++++++++++-
 1 file changed, 79 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts
index 25f707012f62..de1b8b842848 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts
@@ -72,8 +72,11 @@ reg_usdhc2_vqmmc: regulator-usdhc2-vqmmc {
 
 &i2c3 {
 	clock-frequency = <400000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	/* GPIO expander */
@@ -95,6 +98,22 @@ usb3-sata-sel-hog {
 			line-name = "usb3_sata_sel";
 		};
 	};
+
+	/* USB Type-C Controller */
+	typec@3d {
+		compatible = "nxp,ptn5150";
+		reg = <0x3d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ptn5150>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+		port {
+			typec_dr_sw: endpoint {
+				remote-endpoint = <&usb3_drd_sw>;
+			};
+		};
+	};
 };
 
 &snvs_pwrkey {
@@ -108,6 +127,52 @@ &uart2 {
 	status = "okay";
 };
 
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	adp-disable;
+	dr_mode = "otg";
+	hnp-disable;
+	snps,dis-u1-entry-quirk;
+	snps,dis-u2-entry-quirk;
+	srp-disable;
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usb3_drd_sw: endpoint {
+			remote-endpoint = <&typec_dr_sw>;
+		};
+	};
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb3_phy0 {
+	fsl,phy-comp-dis-tune-percent = <115>;
+	fsl,phy-pcs-tx-deemph-3p5db-attenuation-db = <33>;
+	fsl,phy-pcs-tx-swing-full-percent = <100>;
+	fsl,phy-tx-preemp-amp-tune-microamp = <1800>;
+	fsl,phy-tx-vboost-level-microvolt = <1156>;
+	fsl,phy-tx-vref-tune-percent = <122>;
+	status = "okay";
+};
+
+&usb3_phy1 {
+	fsl,phy-tx-preemp-amp-tune-microamp = <1800>;
+	fsl,phy-tx-vref-tune-percent = <116>;
+	status = "okay";
+};
+
 /* SD-card */
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
@@ -129,12 +194,25 @@ MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA                                 0x400001c2
 		>;
 	};
 
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18				0x1c2
+			MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19				0x1c2
+		>;
+	};
+
 	pinctrl_pca9534: pca9534grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15                             0xc0
 		>;
 	};
 
+	pinctrl_ptn5150: ptn5150grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05				0x10
+		>;
+	};
+
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX                            0x40
-- 
2.47.3