[PATCH 19/21] arm64: dts: allwinner: h6: add AC200 EPHY resources

[James Hilliard]

Add the H6 I2C3 controller and pinmux, the PWM-derived 24 MHz AC200
clock, SID calibration cells, RMII pinmux, and the AC200 MFD and EPHY
control nodes.

Describe the co-packaged AC200 INTB output on PB20. Keep both reusable
AC200 nodes disabled so boards must explicitly enable the parent and its
EPHY control function when the companion is present.

Signed-off-by: James Hilliard <james.hilliard1@xxxxxxxxx>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 73 ++++++++++++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 72ce1a75647b..55e6e185a4e5 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -17,6 +17,16 @@ / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	ac200_pwm_clk: ac200-clock {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm1_pin>;
+		pwms = <&pwm 1 42 0>;
+		status = "disabled";
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -314,6 +324,15 @@ ths_calibration: thermal-sensor-calibration@14 {
 			cpu_speed_grade: cpu-speed-grade@1c {
 				reg = <0x1c 0x4>;
 			};
+
+			ephy_calibration: ethernet-phy-calibration@2c,0 {
+				reg = <0x2c 1>;
+				bits = <0 4>;
+			};
+
+			ac200_bandgap: bandgap@30 {
+				reg = <0x30 2>;
+			};
 		};
 
 		timer@3009000 {
@@ -368,6 +387,13 @@ ext_rgmii_pins: rgmii-pins {
 				drive-strength = <40>;
 			};
 
+			ext_rmii_pins: rmii-pins {
+				pins = "PA0", "PA1", "PA2", "PA3", "PA4",
+				       "PA5", "PA6", "PA7", "PA8", "PA9";
+				function = "emac";
+				drive-strength = <40>;
+			};
+
 			hdmi_pins: hdmi-pins {
 				pins = "PH8", "PH9", "PH10";
 				function = "hdmi";
@@ -388,6 +414,12 @@ i2c2_pins: i2c2-pins {
 				function = "i2c2";
 			};
 
+			i2c3_pins: i2c3-pins {
+				pins = "PB17", "PB18";
+				function = "i2c3";
+				bias-pull-up;
+			};
+
 			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2", "PF3",
 				       "PF4", "PF5";
@@ -414,6 +446,11 @@ mmc2_pins: mmc2-pins {
 				bias-pull-up;
 			};
 
+			pwm1_pin: pwm1-pin {
+				pins = "PB19";
+				function = "pwm1";
+			};
+
 			/omit-if-no-ref/
 			spi0_pins: spi0-pins {
 				pins = "PC0", "PC2", "PC3";
@@ -626,6 +663,42 @@ i2c2: i2c@5002800 {
 			#size-cells = <0>;
 		};
 
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-h6-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c3_pins>;
+			clock-frequency = <400000>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ac200: mixed-signal@10 {
+				compatible = "x-powers,ac200";
+				reg = <0x10>;
+				clocks = <&ac200_pwm_clk>;
+				interrupt-parent = <&pio>;
+				interrupts = <1 20 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				nvmem-cells = <&ac200_bandgap>;
+				nvmem-cell-names = "bandgap";
+				status = "disabled";
+
+				ac200_ephy_ctl: ethernet-phy-control {
+					compatible = "x-powers,ac200-ephy-ctl";
+					nvmem-cells = <&ephy_calibration>;
+					nvmem-cell-names = "calibration";
+					phy-mode = "rmii";
+					status = "disabled";
+				};
+			};
+		};
+
 		spi0: spi@5010000 {
 			compatible = "allwinner,sun50i-h6-spi",
 				     "allwinner,sun8i-h3-spi";

-- 
2.53.0