Re: [PATCH v2 1/2] dt-bindings: usb: Add Parade PS5169 redriver bindings

[Esteban Urrutia]

On 7/30/26 3:15 AM, Krzysztof Kozlowski wrote:
> On Wed, Jul 29, 2026 at 02:03:14AM -0400, Esteban Urrutia wrote:
>> Add bindings for the Parade PS5169 and PS5170 USB Type-C linear redrivers.
>> The difference between PS5169 and PS5170 is that PS5170 features an
>> embedded AUX switch, while PS5169 does not.
>> Future-proof the binding by adding PS5170 as well.
>>
>> Signed-off-by: Esteban Urrutia <esteuwu@xxxxxxxxx>
>> ---
>>  .../devicetree/bindings/usb/parade,ps5169.yaml     | 191 +++++++++++++++++++++
>>  1 file changed, 191 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/parade,ps5169.yaml b/Documentation/devicetree/bindings/usb/parade,ps5169.yaml
>> new file mode 100644
>> index 000000000000..86ea2351ee1e
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/parade,ps5169.yaml
>> @@ -0,0 +1,191 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/usb/parade,ps5169.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Parade PS5169 USB Type-C linear redriver
>> +
>> +maintainers:
>> +  - Esteban Urrutia <esteuwu@xxxxxxxxx>
>> +
>> +properties:
>> +  compatible:
>> +    oneOf:
>> +      - items:
>> +          - const: parade,ps5170
>> +          - const: parade,ps5169
>> +      - const: parade,ps5169
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  vcc-supply:
>> +    description: 1.8V power supply
>> +
>> +  reset-gpios:
>> +    maxItems: 1
>> +
>> +  orientation-switch: true
>> +  retimer-switch: true
>> +
>> +  parade,dp-eq-level:
> 
> Use -db suffix instead.
> See https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml

Will do.

>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Equalization level for DisplayPort channels which is mapped to decibels.
>> +    # 0: 2    dB
>> +    # 1: 5.5  dB
>> +    # 2: 6.5  dB
>> +    # 3: 7.5  dB
>> +    # 4: 8    dB
>> +    # 5: 8.5  dB
>> +    # 6: 9.5  dB
>> +    # 7: 10   dB
>> +    enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
>> +
>> +  parade,usb-rx-eq-level:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Equalization level for USB receive channels which is mapped to decibels.
>> +    # 0: 5.2  dB
>> +    # 1: 6    dB
>> +    # 2: 7    dB
>> +    # 3: 8    dB
>> +    # 4: 8.8  dB
>> +    # 5: 9.6  dB
>> +    # 6: 10.4 dB
>> +    # 7: 11.2 dB
>> +    enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
>> +
>> +  parade,usb-tx-eq-level:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Equalization level for USB transmit channels which is mapped to decibels.
>> +    # 0: 2    dB
>> +    # 1: 5.5  dB
>> +    # 2: 6.5  dB
>> +    # 3: 7.5  dB
>> +    # 4: 8    dB
>> +    # 5: 8.5  dB
>> +    # 6: 9.5  dB
>> +    # 7: 10   dB
>> +    enum: [ 0, 1, 2, 3, 4, 5, 6, 7 ]
>> +
>> +  parade,aux-rx-data-reverse:
>> +    type: boolean
>> +    description:
>> +      Please check the driver before specifying this property.
> 
> References to driver make this dubious.

Indeed. I haven't been able to put what this does into words, so I think
I'll drop it and add it back later when I figure that out.

>> +      Usage of this property is design-specific.
>> +
>> +  parade,fine-tune-lfps-swing:
>> +    type: boolean
>> +    description:
>> +      If this property is specified a 50 ohm termination will be set on the USB receive channels.
> 
> s/If this property is specified//
> 
> Just describe the hardware, not the syntax of DTS.

Will fix.

>> +      Usage of this property is design-specific.
>> +
>> +  parade,dp-set-gain:
>> +    type: boolean
>> +    description:
>> +      If this property is specified a gain of -0.9 dB will be applied on the DisplayPort channels.
>> +
>> +  parade,usb-rx-set-gain:
>> +    type: boolean
>> +    description:
>> +      If this property is specified a gain of -0.9 dB will be applied on the USB receive channels.
>> +
>> +  parade,usb-tx-set-gain:
>> +    type: boolean
>> +    description:
>> +      If this property is specified a gain of -0.9 dB will be applied on the USB transmit channels.
>> +
>> +  ports:
>> +    $ref: /schemas/graph.yaml#/properties/ports
>> +    properties:
>> +      port@0:
>> +        $ref: /schemas/graph.yaml#/properties/port
>> +        description: Super Speed (SS) Output endpoint to the Type-C connector
>> +
>> +      port@1:
>> +        $ref: /schemas/graph.yaml#/$defs/port-base
> 
> Why 'port-base' here but 'port' in port@0?

'port' should be used instead of 'port-base' in port@1.
Will fix.

>> +        description: Super Speed (SS) Input endpoint from the Super-Speed PHY
>> +        unevaluatedProperties: false
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - vcc-supply
>> +  - reset-gpios
>> +  - orientation-switch
>> +  - retimer-switch
>> +
>> +allOf:
>> +  - $ref: usb-switch.yaml#
>> +  - $ref: usb-switch-ports.yaml#
>> +  - if:
>> +      properties:
>> +        compatible:
>> +          contains:
>> +            const: parade,ps5170
>> +    then:
>> +      properties:
>> +        ports:
>> +          properties:
>> +            port@2:
> 
> You must define all properties in top-level block and you only disallow
> them. See writing-bindings.

Will fix.

>> +              $ref: /schemas/graph.yaml#/properties/port
>> +              description:
>> +                Sideband Use (SBU) AUX lines endpoint to the Type-C connector for the purpose of
>> +                handling altmode muxing and orientation switching.
>> +    else:
>> +      properties:
>> +        ports:
>> +          properties:
>> +            port@2: false
>> +
>> +additionalProperties: false
Thanks for the review.

Regards,
Esteban