Re: x86: missing FRED #PF event data?

[Sergey Senozhatsky]

On (26/08/10 22:37), Xin Li wrote:
> > On August 10, 2026 6:47:13 PM PDT, Sergey Senozhatsky <senozhatsky@xxxxxxxxxxxx> wrote:
> >> On (26/08/10 08:40), H. Peter Anvin wrote:
> >>> On August 10, 2026 1:58:18 AM PDT, Sergey Senozhatsky <senozhatsky@xxxxxxxxxxxx> wrote:
> >>>> On (26/08/10 16:38), Sergey Senozhatsky wrote:
> >>>>> [..]
> >>>>>> All the crashes are reported as NULL ptr derefs, however, I believe this
> >>>>>> is not exactly the case.  In all crashes CR2 is 0x1000 aligned (we always
> >>>>>> crash accessing first byte of a page).  It seems that csum_partial() calls
> >>>>>> load_unaligned_zeropad() and we hit what load_unaligned_zeropad() comment
> >>>>>> describes as very unlikely) case: "word being a page-crosser and the
> >>>>>> next page not being mapped").  So instead of reading 4 remaining bytes
> >>>>>> of the page and zeroes for trailing 4 bytes, we panic().  It appears that
> >>>>>> FRED #PF is set to 0 while CR2 points to a correct page address.  I added
> >>>>>> a simple printk to exc_page_fault:
> >>>>>> 
> >>>>>>        address = cpu_feature_enabled(X86_FEATURE_FRED) ? fred_event_data(regs) : read_cr2();
> >>>>>>        /* Fall back to CR2 if FRED event data was empty */
> >>>>>>        if (unlikely(!address)) {
> >>>>>>                address = read_cr2();
> >>>>>>                pr_err(":: fixed up address to %lx [[fred: %lx cr2: %lx]]\n", address, fred_event_data(regs), read_cr2());
> >>>>>>        }
> >>>>>> 
> >>>>>> and got the following while running my tests (and well, we don't crash
> >>>>>> anymore):
> >>>>>> 
> >>>>>> [  254.040223] :: fixed up address to ffff9c4d64af4000  [[fred: 0 cr2: ffff9c4d64af4000]]
> >>>>>> ...
> >>>>>> [ 1821.904563] :: fixed up address to ffff9c4e9dd0a000  [[fred: 0 cr2: ffff9c4e9dd0a000]]
> >>>>>> 
> >>>>>> Does any of this make sense to you?
> >>>>> 
> >>>>> I think the explanation is some pKVM shenanigans.  Sorry for the noise.
> >>>> 
> >>>> No, I think we are back at square one.  I thought that maybe pKVM
> >>>> was disabling FRED and that was causing issues.  But I actually see
> >>>> that both cpu_feature_enabled(X86_FEATURE_FRED) and (cr4 & X86_CR4_FRED)
> >>>> claim FRED is enabled, yet fred #PF data is 0 while CR2 holds the correct
> >>>> address.
> >>> 
> >>> What is pKVM? Paravirtualized KVM?
> >> 
> >> Protected KVM.
> >> 
> >>> In that case, it is most likely pKVM not filling in the relevant fields
> >>> in the FRED stack frame, which would be a very serious bug.
> >>> 
> >>> I cannot think of any other way that that could possibly happen otherwise;
> >>> on bare metal those fields are set by hardware and Linux only consumes them.
> >> 
> >> I agree.  I'll look at it from the pKVM side.  I was not aware of pKVM
> >> when I started this discussion, I found out about it later.
> > 
> > If that code calls the FRED entry from KVM routine, that routine doesn't have support for setting event_data in upstream. This would be fixed if necessary.
> 
> Per Sean, it’s “host” running in a VM, so it’s kind of like a filter
> hypervisor you ever mentioned; part of the “host" running in non-root mode.
> 
> So where is this page fault from?  If it’s from non-root mode, does this
> page fault cause a VM exit?  If yes and pKVM forwards it to FRED entry, I
> would guess it is exactly the case.

Added Chuanxiao and Dmytro, folks please correct me.

What I see: the page fault is happening in the non-root mode (native
MMU?).  I don't see a VM exit - I tried injecting FRED #PF data but
exc_page_fault() still reads 0x00 FRED #PF data.  What I also see is
that... it seems to be a hybrid configurations.  From what I can tell,
guests have FRED enabled in CR4, while hypervisor has FRED disabled in
CR4.  So maybe this mix of FRED modes is what pushes empty FRED #PF frame?

Sorry if I babbled complete nonsense.  I'll happily hand it over to
Chuanxiao and Dmytro at this point.