[PATCH] ASoC: tas2783-sdw: do not cache read-only Controls
From: Andrey Golovko
Date: Thu Aug 13 2026 - 14:52:15 EST
The read-only SDCA Controls are readings of device state, but the regmap
caches them and tas2783_reg_default[] gives each one a placeholder, so a
read is answered from the cache and never reaches the peripheral. The
answer is whatever the cache happens to hold: on an ASUS ProArt PX13 a
read of the PDE23 actual power state returns the 0x3 placeholder, i.e.
PS3, while the Function is powered and a cache-bypassing read of the
same Control over the bus answers 0x0. Once the cache has been given a
value it keeps it, so the Control reports a state the device left long
ago.
Mark those Controls volatile and drop their entries from the defaults.
regcache_read() and regcache_write() skip volatile registers, so a
read-only Control no longer enters the cache at all: reads reach the
peripheral, and a sync cannot attempt to write a reading back. That is
what regcache_sync() asks for in the first place - "any registers that
should not be synced should be marked as volatile".
The list is the same one the writeable_reg callback needs, so move it
into a helper both callbacks use. Nothing in the driver reads these
Controls - it performs no register reads at all - so the change is
visible only through the regmap.
Signed-off-by: Andrey Golovko <andrey.golovko@xxxxxxxxx>
---
Applies on top of "ASoC: tas2783-sdw: do not treat read-only Controls as
writable", Message-ID <20260813203500.12106-1-andrey.golovko@xxxxxxxxx>,
whose list of Controls this patch moves into a shared helper.
Tested on an ASUS ProArt PX13 HN7306EAC, two TAS2783 aggregated on SDW1,
on top of broonie/sound for-next. After a cold start the firmware loads
as before and the calibration registers read back byte for byte what
they read without the patch. A regmap read of the PDE23 actual power
state now answers 0x0 on both amplifiers - the state a cache-bypassing
read over the bus reports - where it answered the 0x3 placeholder from
the defaults table before.
sound/soc/codecs/tas2783-sdw.c | 62 ++++++++++++----------------------
1 file changed, 21 insertions(+), 41 deletions(-)
diff --git a/sound/soc/codecs/tas2783-sdw.c b/sound/soc/codecs/tas2783-sdw.c
index 6ed6121a93ee..549f5e621d65 100644
--- a/sound/soc/codecs/tas2783-sdw.c
+++ b/sound/soc/codecs/tas2783-sdw.c
@@ -185,35 +185,17 @@ static const struct reg_default tas2783_reg_default[] = {
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU26, 0x01, 1), 0x1},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU26, 0x0b, 1), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x01, 0), 0x1},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x06, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x07, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x09, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x0a, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS24, 0x02, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS21, 0x02, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS26, 0x02, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS28, 0x02, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_PDE23, 0x1, 0), 0x3},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_SAPU29, 0x05, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_PPU21, 0x06, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_PPU26, 0x06, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT21, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT21, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT29, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT29, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT26, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT26, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT28, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_IT28, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT24, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT24, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT23, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT23, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT25, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT25, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT28, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT28, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MU26, 0x01, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MU26, 0x01, 1), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MU26, 0x01, 2), 0x0},
@@ -222,40 +204,28 @@ static const struct reg_default tas2783_reg_default[] = {
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MU26, 0x01, 5), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MU26, 0x01, 6), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MU26, 0x01, 7), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MU26, 0x06, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT127, 0x04, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT127, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU127, 0x01, 0), 0x1},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU127, 0x01, 1), 0x1},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU127, 0x01, 2), 0x1},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU127, 0x0b, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU127, 0x0b, 1), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU127, 0x0b, 2), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS127, 0x02, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU21, 0x01, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU21, 0x04, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU21, 0x05, 0), 0x1},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU21, 0x08, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU26, 0x01, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU26, 0x04, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU26, 0x05, 0), 0x1},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU26, 0x08, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU23, 0x10, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU26, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x10, 0), 0x1},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x12, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x13, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x14, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x15, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_XU22, 0x16, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS24, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS21, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS26, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS28, 0x10, 0), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_PDE23, 0x10, 0), 0x3},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_UDMPU23, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_SAPU29, 0x10, 0), 0x1},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_SAPU29, 0x11, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_SAPU29, 0x12, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_PPU21, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_PPU21, 0x11, 0), 0x0},
@@ -286,7 +256,6 @@ static const struct reg_default tas2783_reg_default[] = {
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT127, 0x12, 5), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT127, 0x12, 6), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_OT127, 0x12, 7), 0x0},
- {SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_FU127, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_CS127, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU21, 0x10, 0), 0x0},
{SDW_SDCA_CTL(1, TAS2783_SDCA_ENT_MFPU21, 0x11, 0), 0x0},
@@ -495,15 +464,15 @@ static bool tas2783_readable_register(struct device *dev, unsigned int reg)
return tas2783_sdca_mbq_size(dev, reg) > 0;
}
-static bool tas2783_writeable_register(struct device *dev, unsigned int reg)
+/*
+ * The read-only SDCA Controls the driver describes: the Latency of every
+ * Entity, the Clock Valid of every Clock Source, the actual power state of
+ * the Power Domain Entity, the protection status, the algorithm ready flag
+ * and the Extension Unit id, version and firmware download status. None of
+ * them is a setting; every one is a reading of device state.
+ */
+static bool tas2783_read_only_control(unsigned int reg)
{
- /*
- * The Latency Control of every Entity, together with the Power Domain
- * actual state and the protection status, is read-only. They are
- * listed in tas2783_reg_default[] with a placeholder value, so without
- * this a regcache_sync() would try to write them back and the
- * peripheral would reject the transaction, aborting the sync.
- */
switch (reg) {
case SDW_SDCA_CTL(FUNC_NUM_SMART_AMP, TAS2783_SDCA_ENT_FU21, 0x10, 0):
case SDW_SDCA_CTL(FUNC_NUM_SMART_AMP, TAS2783_SDCA_ENT_FU23, 0x10, 0):
@@ -539,15 +508,26 @@ static bool tas2783_writeable_register(struct device *dev, unsigned int reg)
case SDW_SDCA_CTL(FUNC_NUM_SMART_AMP, TAS2783_SDCA_ENT_MFPU21, 0x04, 0):
case SDW_SDCA_CTL(FUNC_NUM_SMART_AMP, TAS2783_SDCA_ENT_MFPU26, 0x08, 0):
case SDW_SDCA_CTL(FUNC_NUM_SMART_AMP, TAS2783_SDCA_ENT_MFPU26, 0x04, 0):
- return false;
+ return true;
default:
- return tas2783_sdca_mbq_size(dev, reg) > 0;
+ return false;
}
}
+static bool tas2783_writeable_register(struct device *dev, unsigned int reg)
+{
+ if (tas2783_read_only_control(reg))
+ return false;
+
+ return tas2783_sdca_mbq_size(dev, reg) > 0;
+}
+
static bool tas2783_volatile_register(struct device *dev, u32 reg)
{
+ if (tas2783_read_only_control(reg))
+ return true;
+
switch (reg) {
case 0x000 ... 0x080: /* Data port 0. */
case 0x100 ... 0x140: /* Data port 1. */
--
2.53.0