[PATCH v2] serial: 8250_uniphier: Use devm_clk_get_enabled()

[Malathi A]

uniphier_uart_probe() enables priv->clk by hand and is then responsible
for disabling it again on every error path. It misses one: when
uart_read_port_properties() fails the function returns directly, leaving
the clock prepared and enabled. The neighbouring path, taken when
serial8250_register_8250_port() fails, does call clk_disable_unprepare(),
which shows the leak is an oversight rather than intent.

Rather than adding another manual unwind, switch to
devm_clk_get_enabled() so the clock is released by devres. That removes
the error path entirely, along with the explicit disables in the
register failure path and in uniphier_uart_remove().

The clock is still disabled and re-enabled by hand across system sleep,
which stays balanced: only SET_SYSTEM_SLEEP_PM_OPS is used, so the
device cannot be unbound while suspended and devres always sees an
enabled clock at detach.

Found by smatch:

  drivers/tty/serial/8250/8250_uniphier.c:232 uniphier_uart_probe() warn: 'priv->clk' from clk_prepare_enable() not released on lines: 205.

Fixes: 26e8349c0d76 ("serial: 8250_uniphier: Switch to use uart_read_port_properties()")
Signed-off-by: Malathi A <malathi.a2000@xxxxxxxxx>
---
Changes in v2:
- Use devm_clk_get_enabled() instead of adding a clk_disable_unprepare()
  to the failing path, as suggested in review. This also lets the
  explicit disables in the serial8250_register_8250_port() error path and
  in uniphier_uart_remove() go away.
- Reworded the commit message accordingly.

 drivers/tty/serial/8250/8250_uniphier.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_uniphier.c b/drivers/tty/serial/8250/8250_uniphier.c
index e3db60bf50c9..6fffac12277a 100644
--- a/drivers/tty/serial/8250/8250_uniphier.c
+++ b/drivers/tty/serial/8250/8250_uniphier.c
@@ -180,16 +180,12 @@ static int uniphier_uart_probe(struct platform_device *pdev)
 
 	memset(&up, 0, sizeof(up));
 
-	priv->clk = devm_clk_get(dev, NULL);
+	priv->clk = devm_clk_get_enabled(dev, NULL);
 	if (IS_ERR(priv->clk)) {
-		dev_err(dev, "failed to get clock\n");
+		dev_err(dev, "failed to get and enable clock\n");
 		return PTR_ERR(priv->clk);
 	}
 
-	ret = clk_prepare_enable(priv->clk);
-	if (ret)
-		return ret;
-
 	up.port.uartclk = clk_get_rate(priv->clk);
 
 	spin_lock_init(&priv->atomic_write_lock);
@@ -222,7 +218,6 @@ static int uniphier_uart_probe(struct platform_device *pdev)
 	ret = serial8250_register_8250_port(&up);
 	if (ret < 0) {
 		dev_err(dev, "failed to register 8250 port\n");
-		clk_disable_unprepare(priv->clk);
 		return ret;
 	}
 	priv->line = ret;
@@ -237,7 +232,6 @@ static void uniphier_uart_remove(struct platform_device *pdev)
 	struct uniphier8250_priv *priv = platform_get_drvdata(pdev);
 
 	serial8250_unregister_port(priv->line);
-	clk_disable_unprepare(priv->clk);
 }
 
 static int __maybe_unused uniphier_uart_suspend(struct device *dev)
-- 
2.43.0