[PATCH net-next v7 10/11] arm64: dts: rockchip: rk3568-photonicat: enable SGMII LAN port

[Coia Prant]

The Ariaboard Photonicat has a Motorcomm YT8521SC Gigabit Ethernet PHY
connected to GMAC0 via XPCS SGMII.  Enable the necessary nodes to make
this port functional.

Add rockchip,sgmii-mac-sel = <0> to the already enabled combphy2,
to route the SGMII interface to GMAC0.  RK3568 has three Combo PHYs
that can carry SGMII; which one is wired to the XPCS is a board-level
choice, and Photonicat uses combphy2.

Enable the xpcs node and its port 0 sub-node, referencing combphy2
as the SerDes PHY.

Add the mdio0 node with the YT8521SC PHY at address 3, including its
reset GPIO and LED configuration.  Also add LED configuration for the
existing RGMII PHY on mdio1 for consistency.

Signed-off-by: Coia Prant <coiaprant@xxxxxxxxx>
---
 .../boot/dts/rockchip/rk3568-photonicat.dts   | 74 ++++++++++++++++++-
 1 file changed, 72 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
index 58c1052ba8ef3..fdaa4a2a4328b 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
@@ -3,6 +3,7 @@
 /dts-v1/;
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/rockchip.h>
 #include <dt-bindings/soc/rockchip,vop2.h>
 #include "rk3568.dtsi"
@@ -241,6 +242,7 @@ &combphy1 {
 };
 
 &combphy2 {
+	rockchip,sgmii-mac-sel = <0>;
 	status = "okay";
 };
 
@@ -260,9 +262,18 @@ &cpu3 {
 	cpu-supply = <&vdd_cpu>;
 };
 
-/* Motorcomm YT8521SC LAN port (require SGMII) */
+/* Motorcomm YT8521SC LAN port */
 &gmac0 {
-	status = "disabled";
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>;
+	assigned-clock-parents = <&clk_gmac0_xpcs_mii>;
+	managed = "in-band-status";
+	pcs-handle = <&xpcs_mii0>;
+	phy-handle = <&sgmii_phy>;
+	phy-mode = "sgmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim>;
+	status = "okay";
 };
 
 /* Motorcomm YT8521SC WAN port */
@@ -341,6 +352,36 @@ &i2s0_8ch {
 	status = "okay";
 };
 
+&mdio0 {
+	sgmii_phy: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x3>;
+		max-speed = <1000>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PC6 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
+	};
+};
+
 &mdio1 {
 	rgmii_phy: ethernet-phy@3 {
 		compatible = "ethernet-phy-ieee802.3-c22";
@@ -350,6 +391,25 @@ rgmii_phy: ethernet-phy@3 {
 		reset-gpios = <&gpio4 RK_PC0 GPIO_ACTIVE_LOW>;
 		rx-internal-delay-ps = <1500>;
 		tx-internal-delay-ps = <1500>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+		};
 	};
 };
 
@@ -586,3 +646,13 @@ &xin32k {
 	pinctrl-names = "default";
 	pinctrl-0 = <&clk32k_out1>;
 };
+
+&xpcs {
+	phys = <&combphy2 PHY_TYPE_SGMII>;
+	phy-names = "serdes";
+	status = "okay";
+};
+
+&xpcs_mii0 {
+	status = "okay";
+};
-- 
2.47.3