[PATCH 11/11] arm64: dts: qcom: sdm845-google-crosshatch: Add display panel

[David Heidelberg via B4 Relay]

From: David Heidelberg <david@xxxxxxx>

Wire up the Samsung AMB630QY01 AMOLED panel on the Pixel 3 XL and drop
the MDSS/DISPCC disables that kept simple-framebuffer alive.

Assisted-by: LLM
Signed-off-by: David Heidelberg <david@xxxxxxx>
---
 .../boot/dts/qcom/sdm845-google-crosshatch.dts     | 60 +++++++++++++++++++---
 1 file changed, 52 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-crosshatch.dts b/arch/arm64/boot/dts/qcom/sdm845-google-crosshatch.dts
index 2a81ca1d00b1b..3b788757b7303 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-google-crosshatch.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-google-crosshatch.dts
@@ -10,27 +10,71 @@ / {
 };
 
 &battery {
 	charge-full-design-microamp-hours = <3480000>;
 	voltage-min-design-microvolt = <3600000>;
 	voltage-max-design-microvolt = <4400000>;
 };
 
-&dispcc {
-	/* Disable for now so simple-framebuffer continues working */
-	status = "disabled";
-};
-
 &framebuffer0 {
 	width = <1440>;
 	height = <2960>;
 	stride = <(1440 * 4)>;
 };
 
-&mdss {
-	/* Disable for now so simple-framebuffer continues working */
-	status = "disabled";
+&ibb {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-soft-start;
+};
+
+&lab {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-soft-start;
+	regulator-pull-down;
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+	status = "okay";
+
+	panel@0 {
+		compatible = "samsung,s6e3ha8-amb630qy01";
+		reg = <0>;
+
+		vdd3-supply = <&vreg_l14a_1p8>;
+		vci-supply = <&vreg_l28a_3p0>;
+		vddpos-supply = <&lab>;
+		vddneg-supply = <&ibb>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&panel_default>;
+		pinctrl-names = "default";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1 2 3>;
+	remote-endpoint = <&panel_in>;
+	qcom,te-source = "mdp_vsync_e";
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vdda_mipi_dsi0_pll>;
+
+	status = "okay";
 };
 
 &wifi {
 	qcom,calibration-variant = "Google_crosshatch";
 };

-- 
2.55.0