[PATCH 4/5] arm64: dts: qcom: Add PMIC support for Maili platforms

[Jingyi Wang]

From: Fenglin Wu <fenglin.wu@xxxxxxxxxxxxxxxx>

Add PMIC files for pmic-arbiter device used on Maili QRD and MTP boards.
Only one PMH0104 chip is used on SPMI bus-0 with SID 0x2 which is a new
usage, hence add a new pmh0104-maili.dtsi. Also, add a new pmg1110.dtsi
to support PMG1110 usage.

Signed-off-by: Fenglin Wu <fenglin.wu@xxxxxxxxxxxxxxxx>
Signed-off-by: Jingyi Wang <jingyi.wang@xxxxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/pmg1110.dtsi       | 57 +++++++++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/pmh0104-maili.dtsi | 57 +++++++++++++++++++++++++++++
 2 files changed, 114 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pmg1110.dtsi b/arch/arm64/boot/dts/qcom/pmg1110.dtsi
new file mode 100644
index 000000000000..31b05003b843
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmg1110.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmg1110-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pmg1110_k_e1_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus1 {
+	pmg1110_k_e1: pmic@9 {
+		compatible = "qcom,pmg1110", "qcom,spmi-pmic";
+		reg = <0x9 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmg1110_k_e1_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x9 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmg1110_k_e1_gpios: gpio@8800 {
+			compatible = "qcom,pmg1110-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmg1110_k_e1_gpios 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/pmh0104-maili.dtsi b/arch/arm64/boot/dts/qcom/pmh0104-maili.dtsi
new file mode 100644
index 000000000000..2f3906ccaa73
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmh0104-maili.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmh0104-c-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pmh0104_c_e0_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus0 {
+	pmh0104_c_e0: pmic@2 {
+		compatible = "qcom,pmh0104", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmh0104_c_e0_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmh0104_c_e0_gpios: gpio@8800 {
+			compatible = "qcom,pmh0104-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmh0104_c_e0_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};

-- 
2.34.1