[PATCH 08/38] arm: dts: qcom: apq8060: Add newline between subnodes
From: Waqar Hameed
Date: Thu Oct 01 2026 - 18:40:45 EST
There should be a newline between subnodes. Found/fixed with
dtfmt (Devicetree Source formatter).
Signed-off-by: Waqar Hameed <waqar.hameed@xxxxxxxx>
---
.../dts/qcom/qcom-apq8060-dragonboard.dts | 22 +++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
index 009afd8212c22..fa2b372e51bf3 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -181,6 +181,7 @@ eeprom@52 {
vcc-supply = <&pm8058_s3>;
pagesize = <64>;
};
+
wm8903: wm8903@1a {
/* This Woolfson Micro device has an unrouted interrupt line */
compatible = "wlf,wm8903";
@@ -226,6 +227,7 @@ ak8975@c {
vid-supply = <&pm8058_lvs0>; // 1.8V
vdd-supply = <&pm8058_l14>; // 2.85V
};
+
bmp085@77 {
compatible = "bosch,bmp085";
reg = <0x77>;
@@ -237,6 +239,7 @@ bmp085@77 {
vddd-supply = <&pm8058_lvs0>; // 1.8V
vdda-supply = <&pm8058_l14>; // 2.85V
};
+
mpu3050@68 {
compatible = "invensense,mpu3050";
reg = <0x68>;
@@ -287,6 +290,7 @@ pinconf {
power-source = <PM8058_GPIO_S3>;
};
};
+
dragon_bmp085_gpios: bmp085-state {
pinconf {
pins = "gpio16";
@@ -296,6 +300,7 @@ pinconf {
power-source = <PM8058_GPIO_S3>;
};
};
+
dragon_mpu3050_gpios: mpu3050-state {
pinconf {
pins = "gpio17";
@@ -305,6 +310,7 @@ pinconf {
power-source = <PM8058_GPIO_S3>;
};
};
+
dragon_sdcc3_gpios: sdcc3-state {
pinconf {
pins = "gpio22";
@@ -314,6 +320,7 @@ pinconf {
power-source = <PM8058_GPIO_S3>;
};
};
+
dragon_sdcc5_gpios: sdcc5-state {
pinconf {
pins = "gpio26";
@@ -324,6 +331,7 @@ pinconf {
power-source = <PM8058_GPIO_S3>;
};
};
+
dragon_ak8975_gpios: ak8975-state {
pinconf {
pins = "gpio33";
@@ -333,6 +341,7 @@ pinconf {
power-source = <PM8058_GPIO_S3>;
};
};
+
dragon_cm3605_gpios: cm3605-state {
/* Pin 34 connected to the proxy IRQ */
gpio34-pins {
@@ -342,6 +351,7 @@ gpio34-pins {
bias-disable;
power-source = <PM8058_GPIO_S3>;
};
+
/* Pin 35 connected to ASET */
gpio35-pins {
pins = "gpio35";
@@ -351,6 +361,7 @@ gpio35-pins {
power-source = <PM8058_GPIO_S3>;
};
};
+
dragon_veth_gpios: veth-state {
pinconf {
pins = "gpio40";
@@ -521,12 +532,14 @@ pm8901_s2: s2 {
qcom,switch-mode-frequency = <1600000>;
bias-pull-down;
};
+
pm8901_s3: s3 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
qcom,switch-mode-frequency = <1600000>;
bias-pull-down;
};
+
pm8901_s4: s4 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
@@ -837,12 +850,14 @@ clk-pins {
drive-strength = <16>;
bias-disable;
};
+
cmd-pins {
pins = "gpio168"; /* SDC1 CMD */
function = "sdc1";
drive-strength = <10>;
bias-pull-up;
};
+
data-pins {
/* SDC1 D0 to D7 */
pins = "gpio159", "gpio160", "gpio161", "gpio162",
@@ -863,11 +878,13 @@ clk-pins {
drive-strength = <8>;
bias-disable;
};
+
cmd-pins {
pins = "sdc3_cmd";
drive-strength = <8>;
bias-pull-up;
};
+
data-pins {
pins = "sdc3_data";
drive-strength = <8>;
@@ -883,12 +900,14 @@ clk-pins {
drive-strength = <16>;
bias-disable;
};
+
cmd-pins {
pins = "gpio95"; /* SDC5 CMD */
function = "sdc5";
drive-strength = <10>;
bias-pull-up;
};
+
data-pins {
/* SDC5 D0 to D3 */
pins = "gpio96", "gpio98", "gpio99", "gpio100";
@@ -930,6 +949,7 @@ tx-pins {
drive-strength = <8>;
bias-disable;
};
+
rx-pins {
pins = "gpio118";
function = "gsbi12";
@@ -951,6 +971,7 @@ mux0-pins {
"gpio134"; /* CS0_N testpoint TP29 */
function = "ebi2cs";
};
+
mux1-pins {
pins =
/* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
@@ -983,6 +1004,7 @@ reset-pins {
drive-strength = <6>;
bias-disable;
};
+
irq-pins {
pins = "gpio61"; /* IRQ line */
function = "gpio";
--
2.43.0