[PATCH rtw-next v6 4/4] wifi: rtw88: sdio: Split rtw_sdio_rx_isr into 8051 and 3081 variants

[Alastair D'Silva]

Split rtw_sdio_rx_isr() into separate 8051 and 3081 variants to be
clear. The two differences between the architectures are:
- Register size: REG_SDIO_RX0_REQ_LEN is 16-bit on 8051, 32-bit on 3081.
- HISR behavior: 8051 re-reads REG_SDIO_HISR on each iteration, while
  3081 drains based on rx_len without re-reading HISR.

This is a refactoring without any logic changes.

Assisted-by: LLM
Acked-by: Ping-Ke Shih <pkshih@xxxxxxxxxxx>
Reviewed-by: Luka Gejak <luka.gejak@xxxxxxxxx>
Signed-off-by: Alastair D'Silva <alastair@xxxxxxxxxxx>
---
 drivers/net/wireless/realtek/rtw88/sdio.c | 58 +++++++++++++----------
 1 file changed, 33 insertions(+), 25 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtw88/sdio.c b/drivers/net/wireless/realtek/rtw88/sdio.c
index e459541b7678..3569aae0f2f0 100644
--- a/drivers/net/wireless/realtek/rtw88/sdio.c
+++ b/drivers/net/wireless/realtek/rtw88/sdio.c
@@ -1439,17 +1439,13 @@ static int rtw_sdio_rxfifo_recv(struct rtw_dev *rtwdev, u32 rx_len)
 	return 0;
 }
 
-static void rtw_sdio_rx_isr(struct rtw_dev *rtwdev)
+static void rtw_sdio_rx_isr_8051(struct rtw_dev *rtwdev)
 {
 	u32 rx_len, hisr, total_rx_bytes = 0;
 	int ret;
 
 	do {
-		if (rtw_chip_wcpu_8051(rtwdev))
-			rx_len = rtw_read16(rtwdev, REG_SDIO_RX0_REQ_LEN);
-		else
-			rx_len = rtw_read32(rtwdev, REG_SDIO_RX0_REQ_LEN);
-
+		rx_len = rtw_read16(rtwdev, REG_SDIO_RX0_REQ_LEN);
 		if (!rx_len)
 			break;
 
@@ -1459,33 +1455,45 @@ static void rtw_sdio_rx_isr(struct rtw_dev *rtwdev)
 
 		total_rx_bytes += rx_len;
 
-		if (rtw_chip_wcpu_8051(rtwdev)) {
-			/* Stop if no more RX requests are pending, even if
-			 * rx_len could be greater than zero in the next
-			 * iteration. This is needed because the RX buffer may
-			 * already contain data while either HW or FW are not
-			 * done filling that buffer yet. Still reading the
-			 * buffer can result in packets where
-			 * rtw_rx_pkt_stat.pkt_len is zero or points beyond the
-			 * end of the buffer.
-			 */
-			hisr = rtw_read32(rtwdev, REG_SDIO_HISR);
-		} else {
-			/* RTW_WCPU_3081 chips have improved hardware or
-			 * firmware and can use rx_len unconditionally.
-			 */
-			hisr = REG_SDIO_HISR_RX_REQUEST;
-		}
+		/*
+		 * Stop if no more RX requests are pending, even if
+		 * rx_len could be greater than zero in the next
+		 * iteration. This is needed because the RX buffer may
+		 * already contain data while either HW or FW are not
+		 * done filling that buffer yet. Still reading the
+		 * buffer can result in packets where
+		 * rtw_rx_pkt_stat.pkt_len is zero or points beyond the
+		 * end of the buffer.
+		 */
+		hisr = rtw_read32(rtwdev, REG_SDIO_HISR);
 	} while (total_rx_bytes < SZ_64K && hisr & REG_SDIO_HISR_RX_REQUEST);
 }
 
+static void rtw_sdio_rx_isr_3081(struct rtw_dev *rtwdev)
+{
+	u32 rx_len, total_rx_bytes = 0;
+	int ret;
+
+	do {
+		rx_len = rtw_read32(rtwdev, REG_SDIO_RX0_REQ_LEN);
+		if (!rx_len)
+			break;
+
+		ret = rtw_sdio_rxfifo_recv(rtwdev, rx_len);
+		if (ret)
+			break;
+
+		total_rx_bytes += rx_len;
+	} while (total_rx_bytes < SZ_64K);
+}
+
 static void rtw_sdio_handle_interrupt_8051(struct rtw_dev *rtwdev, u32 hisr)
 {
 	if (hisr & REG_SDIO_HISR_TXERR)
 		rtw_sdio_tx_err_isr(rtwdev);
 	if (hisr & REG_SDIO_HISR_RX_REQUEST) {
 		hisr &= ~REG_SDIO_HISR_RX_REQUEST;
-		rtw_sdio_rx_isr(rtwdev);
+		rtw_sdio_rx_isr_8051(rtwdev);
 	}
 
 	/*
@@ -1515,7 +1523,7 @@ static void rtw_sdio_handle_interrupt_3081(struct rtw_dev *rtwdev, u32 hisr)
 	if (hisr & REG_SDIO_HISR_TXERR)
 		rtw_sdio_tx_err_isr(rtwdev);
 	if (hisr & REG_SDIO_HISR_RX_REQUEST)
-		rtw_sdio_rx_isr(rtwdev);
+		rtw_sdio_rx_isr_3081(rtwdev);
 
 	/*
 	 * Unmasking HIMR re-asserts the IRQ line if new packets arrived or if
-- 
2.53.0