Re: [PATCH v4 5/7] arm64: dts: ti: k3-j784s4-ti-ipc-firmware: Reserve memory for LPM metadata

[Kumar, Udit]

On 9/21/2026 8:23 PM, Richard Genoud (TI) wrote:
> Declare a carveout memory region to store LPM metadata on J784S4.
> 
> For Jacinto devices, this memory region is needed for saving ATF context
> and the certificate information of ATF and OPTEE and DM image. This LPM
> metadata area is firewalled to be accessed only by TIFS.
> 
> U-Boot R5 SPL/TIFS will use this area to save and restore:
> - ATF context
> - ATF certificate information
> - OPTEE certificate information
> - DM image (which has been copied in memory at boot time by U-Boot
>   R5-SPL)
> 
> At resume, U-Boot R5 SPL is executed and detects that the board is
> resuming (with a flag set in the PMIC), then it:
> - brings out of retention the DDR
> - retrieves the LPM memory region from DTS
> - authenticates certificates from LPM memory region and applies firewalls
> - asks TIFS to restore TFA and its own minimal context
> - starts TFA on remote proc
> - loads back DM image from memory and jumps to DM
> 
> https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html#lpm-msg-lpm-save-addr
> 
> As this is used by U-Boot SPL, bootph-pre-ram is added and the device is
> enabled.
> 
> NB: This memory region is not part of DM memory (which is not retained
> at suspend)
> 
> Signed-off-by: Prasanth Babu Mantena <p-mantena@xxxxxx>
> Signed-off-by: Richard Genoud (TI) <richard.genoud@xxxxxxxxxxx>
> ---
>  .../boot/dts/ti/k3-j784s4-ti-ipc-firmware.dtsi    | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-ti-ipc-firmware.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-ti-ipc-firmware.dtsi
> index 81b508b9b05e..1c0c1533f0a3 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-ti-ipc-firmware.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-ti-ipc-firmware.dtsi
> @@ -17,6 +17,12 @@ c71_3_memory_region: memory@ab100000 {
>  		reg = <0x00 0xab100000 0x00 0xf00000>;
>  		no-map;
>  	};
> +
> +	lpm_memory_region: memory@ac000000 {
> +		reg = <0x00 0xac000000 0x00 0x00300000>;
> +		no-map;
> +		bootph-pre-ram;
> +	};

Could you move this carveout near to optee
0x9E500000 to 0x9E800000 as LPM memory,

Since 0xa***_**** is used by firmware and this is just place-holder for
lpm meta data.

Also better to move this k3-j784s4-j742s2-ti-ipc-firmware-common.dtsi
file as these two SOCs are same and uses same map

Thanks
Udit


>  };
>  
>  &mailbox0_cluster5 {
> @@ -27,6 +33,15 @@ mbox_c71_3: mbox-c71-3 {
>  	};
>  };
>  
> +&mcu_r5fss0_core0 {
> +	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
> +			<&mcu_r5fss0_core0_memory_region>,
> +			<&lpm_memory_region>;
> +	memory-region-names = "dma", "firmware", "lpm-metadata";
> +	bootph-pre-ram;
> +	status = "okay";
> +};
> +
>  &c71_3 {
>  	mboxes = <&mailbox0_cluster5 &mbox_c71_3>;
>  	memory-region = <&c71_3_dma_memory_region>,