[PATCH 2/5] riscv: dts: spacemit: k3-com260: Move SD card to the module

[Troy Mitchell]

The SD card slot, its power supply and the signal-voltage switching
circuitry reside on the K3 CoM260 module. Describing the slot only in
the IFX carrier board leaves other CoM260 carriers without this shared
hardware description.

Move the SD controller configuration into the module include without
changing its properties, so every carrier using the module inherits it.

Signed-off-by: Troy Mitchell <troy.mitchell@xxxxxxxxxxxxxxxxxx>
---
 arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts | 17 -----------------
 arch/riscv/boot/dts/spacemit/k3-com260.dtsi    | 17 +++++++++++++++++
 2 files changed, 17 insertions(+), 17 deletions(-)

diff --git a/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts b/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
index 6e295bc6f196..38809d01df82 100644
--- a/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts
@@ -111,20 +111,3 @@ hub_3_0: hub@2 {
 &usb3b_u2phy {
 	status = "okay";
 };
-
-&sdhci0 {
-	pinctrl-names = "default","uhs";
-	pinctrl-0 = <&mmc1_cfg>;
-	pinctrl-1 = <&mmc1_uhs_cfg>;
-	bus-width = <4>;
-	cd-gpios = <&gpio K3_GPIO(4) GPIO_ACTIVE_HIGH>;
-	no-mmc;
-	no-sdio;
-	disable-wp;
-	cap-sd-highspeed;
-	vqmmc-supply = <&aldo1>;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
diff --git a/arch/riscv/boot/dts/spacemit/k3-com260.dtsi b/arch/riscv/boot/dts/spacemit/k3-com260.dtsi
index 054bfff7413a..f2df797a2c80 100644
--- a/arch/riscv/boot/dts/spacemit/k3-com260.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3-com260.dtsi
@@ -233,6 +233,23 @@ phy1: ethernet-phy@1 {
 	};
 };
 
+&sdhci0 {
+	pinctrl-names = "default","uhs";
+	pinctrl-0 = <&mmc1_cfg>;
+	pinctrl-1 = <&mmc1_uhs_cfg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio K3_GPIO(4) GPIO_ACTIVE_HIGH>;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	cap-sd-highspeed;
+	vqmmc-supply = <&aldo1>;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_0_cfg>;

-- 
2.56.0