Re: [PATCH net-next 2/2] net: stmmac: dwmac-motorcomm: support Wake-on-LAN from S5

From: Yao Zi

Date: Mon Nov 16 2026 - 10:17:50 EST


On Mon, Nov 16, 2026 at 03:08:06PM +0000, Yao Zi wrote:
> On Mon, Nov 16, 2026 at 06:17:57AM -0300, Magnus Leatti wrote:
> > The driver reports "Supports Wake-on: ug" and accepts "wol g", but a
> > YT6801 in S5 ignores magic packets. At power-off stmmac_suspend() arms
> > the PMT register, but the chip's out-of-band WoL block stays disabled
> > as motorcomm_init() leaves it, the packet wake bit in WOL_CTRL is clear
> > and PME is turned off.
> >
> > When powering off with Wake-on-LAN set, the interface up and wakeup
> > enabled for the device, keep PME enabled and arm the chip after
> > stmmac_suspend():
> >
> > - Enable OOB WoL. Without it the chip does not wake.
> > - Write the MAC address in use to the first address filter again.
> > Enabling OOB WoL reloads the factory address there. Without the
> > rewrite the chip wakes on the factory address and ignores the one
> > in use. The rewrite follows a 2 ms wait, as in the vendor driver:
> > without the wait the reload lands after the rewrite.
> > - Set the packet wake enable bit in WOL_CTRL. Without it the chip
> > does not wake.
> >
> > The sequence follows the vendor driver, with two differences. The
> > vendor also sets bit 9 of LPW_CTRL. The chip wakes without it, so it is
> > left alone. The vendor puts the function in D3hot. Here it stays in D0.
> > With MAC Wake-on-LAN phylink keeps the PHY running and phylib keeps
> > polling it until power is removed. In D3hot the MDIO registers read as
> > all-ones, the poll fails with -EBUSY and phylib warns from
> > phy_error_precise(). That warning was seen 111 ms after entering D3hot
> > on a normal power-off.
> >
> > The PHY is left at the negotiated speed. Reboot and kexec are not
> > armed: OOB WoL can only be disabled again by a chip reset, so it is
> > enabled only when powering off, and the next probe resets the chip. If
> > the interface is down at power-off, the system does not wake.
> >
> > Suspend is not changed. Hibernation that powers off through the
> > shutdown path arms the chip the same way. Neither was tested.
> >
> > Tested on a Celeron N3350 mini PC, magic packets sent from another host
> > 75 s after power-off:
> >
> > net-next wol g no wake, 3 of 3
> > patched wol g wake, 8 of 8 (28-31 s to ping)
> > patched wol u wake on unicast, 1 of 1
> > patched wol d no wake, 3 of 3
> > patched wol g, interface down no wake, 1 of 1
> > patched wol g, power/wakeup disabled no wake, 1 of 1
> > patched wol g, reboot reboots, link back, 3 of 3
> >
> > The kernel log of each of these shutdowns, read back after the next
> > boot, shows no warning from the shutdown path.
> >
> > A second board, a PSJ8500-N97 mini PC (Intel N97), behaves the same.
> >
> > Signed-off-by: Magnus Leatti <magnusleatti@xxxxxxxxxxxxxx>
> > ---
> > .../ethernet/stmicro/stmmac/dwmac-motorcomm.c | 68 ++++++++++++++++++-
> > 1 file changed, 65 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-motorcomm.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-motorcomm.c
> > index 1e142ad39e33..034547ad1e98 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-motorcomm.c
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-motorcomm.c
>
> [...]
>
> > @@ -204,9 +207,51 @@ static int motorcomm_resume(struct device *dev, void *bsp_priv)
> > return 0;
> > }
> >
> > +/*
> > + * Arm the chip to wake the system from S5. stmmac_suspend() has already
> > + * programmed the PMT register of the GMAC. The rest lives in the wrapper.
> > + */
> > +static void motorcomm_arm_s5_wake(struct net_device *ndev)
> > +{
> > + struct stmmac_priv *spriv = netdev_priv(ndev);
> > + struct dwmac_motorcomm_priv *priv = spriv->plat->bsp_priv;
> > + u32 reg;
> > +
> > + /*
> > + * motorcomm_init() disables OOB WoL right after the chip reset, as
> > + * normal operation requires. With it disabled the chip ignores wake
> > + * packets once the system is off. Once it has been enabled, only a
> > + * chip reset disables it again, so enable it only when powering off.
> > + */
> > + reg = readl(priv->base + OOB_WOL_CTRL);
> > + reg &= ~OOB_WOL_CTRL_DIS;
> > + writel(reg, priv->base + OOB_WOL_CTRL);
> > +
> > + /*
> > + * Enabling OOB WoL reloads the address from eFuse into the first
> > + * MAC address filter. Write the address in use again, or the chip
> > + * wakes on the factory address only. The reload is not immediate:
> > + * without the wait, taken from the vendor driver, it overwrites
> > + * the address written here.
> > + */
> > + usleep_range(2000, 3000);
> > +
> > + rtnl_lock();
> > + phylink_rx_clk_stop_block(spriv->phylink);
> > + stmmac_set_umac_addr(spriv, spriv->hw, ndev->dev_addr, 0);
>
> Does the chip automatically enables WoL and loads MAC from eFuse on
> power-on? If so, the driver's WoL behavior would vary if the software

Aside from a clean power-on, its behavior on reset also matters. If the
NIC falls into WoL on both power-on and reset with a reasonable MAC
address set already, we might probably call stmmac_dvr_remove() in
.shutdown() to detach the NIC from kernel's infrastructure, then reset
it with SYS_RESET to get a functional WoL state in S5.

> alternates the NIC's MAC address, depending whether it's a cold boot or
> a warm one.
>
> Please confirm the chip's behavior on reset.
>
> > + phylink_rx_clk_stop_unblock(spriv->phylink);
> > + rtnl_unlock();
> > +
> > + reg = readl(priv->base + WOL_CTRL);
> > + reg |= WOL_CTRL_PKT_EN;
> > + writel(reg, priv->base + WOL_CTRL);
> > +}
>
> [...]
>
> --
> Thanks,
> Yao Zi
>
> Meow-mrrp-mrow, I'm a cat.

--
Thanks,
Yao Zi

Meow-mrrp-mrow, I'm a cat.