Re: [PATCH v2 2/2] dmaengine: pl08x: Use the channel count from the device tree
From: Frank Li
Date: Mon Nov 16 2026 - 15:27:37 EST
On Fri, Nov 06, 2026 at 03:25:59PM +0800, David Yang wrote:
> [You don't often get email from mmyangfl@xxxxxxxxx. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
>
> The Hi3798MV100 DMAC is a plain PL080 except for the channel count: 4
> instead of 8. The part ID does not say, and the driver takes the count
> from the matched vendor_data entry. The entry is shared between
> instances; the adjustment lands in a private copy. dma-common.yaml
> already defines dma-channels for a controller node. Honor it.
>
> Signed-off-by: David Yang <mmyangfl@xxxxxxxxx>
> ---
Reviewed-by: Frank Li <Frank.Li@xxxxxxx>
> drivers/dma/amba-pl08x.c | 25 +++++++++++++++++++++++--
> 1 file changed, 23 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c
> index 9f5e4f5fb877..27c61a7f2082 100644
> --- a/drivers/dma/amba-pl08x.c
> +++ b/drivers/dma/amba-pl08x.c
> @@ -282,7 +282,7 @@ struct pl08x_driver_data {
> bool has_slave;
> void __iomem *base;
> struct amba_device *adev;
> - const struct vendor_data *vd;
> + struct vendor_data *vd;
> struct pl08x_platform_data *pd;
> struct pl08x_phy_chan *phy_chans;
> struct dma_pool *pool;
> @@ -2698,6 +2698,7 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
> struct device_node *np = adev->dev.of_node;
> struct reset_control *rst;
> u32 tsfr_size;
> + u32 channels;
> int ret = 0;
> int i;
>
> @@ -2719,7 +2720,6 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
>
> /* Assign useful pointers to the driver state */
> pl08x->adev = adev;
> - pl08x->vd = vd;
>
> pl08x->base = ioremap(adev->res.start, resource_size(&adev->res));
> if (!pl08x->base) {
> @@ -2727,6 +2727,17 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
> goto out_no_ioremap;
> }
>
> + /*
> + * vd points into the shared id table; give the instance its own
> + * copy before anything below starts adjusting it.
> + */
> + pl08x->vd = devm_kmemdup(&adev->dev, vd, sizeof(*vd), GFP_KERNEL);
> + if (!pl08x->vd) {
> + ret = -ENOMEM;
> + goto out_no_platdata;
> + }
> + vd = pl08x->vd;
> +
> /* Release the reset before reading registers */
> rst = devm_reset_control_get_optional_shared_deasserted(&adev->dev, NULL);
> if (IS_ERR(rst)) {
> @@ -2756,6 +2767,16 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
> vd->dualmaster = !!(val & BIT(9));
> }
>
> + /* Read the channel number from the node if specified */
> + if (!of_property_read_u32(np, "dma-channels", &channels) && channels) {
> + if (channels > vd->channels)
> + dev_warn(&adev->dev,
> + "using %u channels, instead of %u from the node\n",
> + vd->channels, channels);
> + else
> + vd->channels = channels;
> + }
> +
> /* Initialize memcpy engine */
> dma_cap_set(DMA_MEMCPY, pl08x->memcpy.cap_mask);
> pl08x->memcpy.dev = &adev->dev;
> --
> 2.53.0
>