Re: [PATCH net v3] net: stmmac: Clear DMA errors for multi-channel interrupts
From: Maxime Chevallier
Date: Tue Nov 17 2026 - 03:49:12 EST
Hi,
On 11/16/26 11:32, netdev-bot+sashiko@xxxxxxxxxx wrote:
> Thank you for your contribution! Sashiko AI review found 2 potential
> issue(s) to consider.
>
> Critical: 0 · High: 0 (1) · Medium: 1 (1) · Low: 1 (1)
>
> If you believe none of the issues are legitimate, please reply to each
> issue of Medium severity or higher and explain why the AI is wrong.
> If any of them are legitimate and you plan to respin, please let patchwork
> know by including "pw-bot: cr" as a separate line at the end of your reply
> (one such reply per series is enough).
>
> - [Medium] In multi-MSI (INTM=1) mode the patch makes the MAC vector
> responsible for fatal bus errors.
> - [Low] stmmac_dma_err_interrupt(), called from the MAC hardirq for every
> channel, adds another unserialized writer of the plain `unsigned long`…
>
> Pre-existing issues:
> - [High] This problem wasn't introduced by this patch, but the patch adds
> a new hardirq source that arms it.
> - [Medium] This problem wasn't introduced by this patch, but it concerns
> how dwmac4_dma_interrupt() acknowledges status.
> - [Low] This problem wasn't introduced by this patch, but Loongson is not
> covered by it.
>
> --
>
> net: stmmac: Clear DMA errors for multi-channel interrupts
>
> This adds a DMA_DIR_ERR direction and a DMA_CHAN_STATUS_MSK_ERR mask for
> dwmac4. On GMAC4 cores, the multi-MSI MAC interrupt handler now calls a new
> stmmac_dma_err_interrupt(). That helper acks AIS/FBE/RPS/RBU on every
> channel and calls stmmac_global_err() on fatal bus errors. The goal is to
> stop the RBU/RPS interrupt storms seen on dwmac-motorcomm.
>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h
>> index 43b036d4e95bd..a7caac3c98e6c 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h
>> @@ -173,6 +173,11 @@ static inline u32 dma_chanx_base_addr(const struct dwmac4_addrs *addrs,
>> DMA_CHAN_STATUS_TI | \
>> DMA_CHAN_STATUS_MSK_COMMON)
>>
>> +#define DMA_CHAN_STATUS_MSK_ERR (DMA_CHAN_STATUS_AIS | \
>
> [Severity: Medium]
>
> This is a pre-existing issue, but does putting DMA_CHAN_STATUS_AIS in this
> mask actually clear AIS on 4.00 cores?
Pre-existing, this should be addressed separately
[...]
>
> [Severity: Low]
>
> Can one hardware event now be counted twice in the abnormal counters?
>
> stmmac_dma_err_interrupt() runs this path from the MAC hardirq for every
> channel. The per-channel RX/TX MSI handlers process the same bits:
> DMA_CHAN_STATUS_MSK_RX contains RBU, RPS, AIS and FBE, and
> DMA_CHAN_STATUS_MSK_TX contains AIS and FBE.
>
> The counters are plain unsigned long increments:
>
> if (unlikely(intr_status & DMA_CHAN_STATUS_RBU))
> x->rx_buf_unav_irq++;
> if (unlikely(intr_status & DMA_CHAN_STATUS_RPS))
> x->rx_process_stopped_irq++;
> ...
> x->fatal_bus_error_irq++;
>
> Suppose RBU, RPS or FBE arrives together with RI or TI on a channel. Both
> vectors can then read the bit before either one writes it back. Could
> rx_buf_unav_irq, rx_process_stopped_irq and fatal_bus_error_irq in
> ethtool -S then count the event twice? The concurrent read-modify-write
> could also lose increments.
I'd say, this is both unlikely and acceptable for these counters
>
> [ ... ]
>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> index 25894771e9e9f..0bcbf837d9cc8 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> @@ -3145,6 +3145,22 @@ static int stmmac_napi_check(struct stmmac_priv *priv, u32 chan, u32 dir)
>> return status;
>> }
>>
>> +static void stmmac_dma_err_interrupt(struct stmmac_priv *priv)
>> +{
>> + u8 channels_to_check = max(priv->plat->rx_queues_to_use,
>> + priv->plat->tx_queues_to_use);
>> + int status;
>> + u8 chan;
>> +
>> + for (chan = 0; chan < channels_to_check; chan++) {
>> + status = stmmac_dma_interrupt_status(priv, priv->ioaddr,
>> + &priv->xstats, chan,
>> + DMA_DIR_ERR);
>> + if (unlikely(status & tx_hard_error))
>> + stmmac_global_err(priv);
>
> [Severity: Medium]
>
> Can the per-channel MSI handlers consume the fatal bus error before this
> loop sees it?
This is also pre-existing for multi-MSI handling then.
[...]
> [Severity: Low]
>
> This isn't a bug introduced by this patch, but Loongson multi-MSI is left
> out here. loongson_default_data() sets:
>
> plat->core_type = DWMAC_CORE_GMAC;
Yeah I mentionned it in the commit log... The only loognson board I have (2k0300)
uses dwmac-generic and not the loogson glue, so I can't test that one, let's
see if anyone sees that hang on the affected platforms.
Maxime