Re: [PATCH v2 3/5] arm64: dts: imx95-phyflex-libra-rdk: Add overlays

From: Benjamin Hahn

Date: Tue Nov 17 2026 - 04:33:05 EST


Am 13.11.26 um 17:32 schrieb Frank Li:
On Fri, Nov 13, 2026 at 05:00:05PM +0100, Benjamin Hahn wrote:

subject Add overlay for som temperature sensors and ...

Add overlays for SoM temperature sensors and M.2 Key-E WIFI/BT cards
that need the nxp,88w8987-bt compatible in devicetree (tested on
IW611/IW612).

Signed-off-by: Benjamin Hahn <B.Hahn@xxxxxxxxx>
---
arch/arm64/boot/dts/freescale/Makefile | 9 ++++++++
.../imx95-phyflex-fpsc-g-som-temperature.dtso | 23 +++++++++++++++++++++
.../imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso | 24 ++++++++++++++++++++++
which is independ, suggest use two patches to do that.
Will do

3 files changed, 56 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 4eb7508193e7..17b357f4886a 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -739,7 +739,16 @@ imx95-19x19-evk-pcie1-ep-dtbs += imx95-19x19-evk.dtb imx-pcie1-ep.dtbo
dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk-pcie0-ep.dtb imx95-19x19-evk-pcie1-ep.dtb
dtb-$(CONFIG_ARCH_MXC) += imx95-libra-rdk-fpsc.dtb

+imx95-phyflex-fpsc-g-som-temperature-dtbs := \
+ imx95-phyflex-libra-rdk.dtb \
+ imx95-phyflex-fpsc-g-som-temperature.dtbo
+imx95-phyflex-libra-rdk-bluetooth-88w8987-dtbs := \
+ imx95-phyflex-libra-rdk.dtb \
+ imx95-phyflex-libra-rdk-bluetooth-88w8987.dtbo
+
dtb-$(CONFIG_ARCH_MXC) += imx95-phyflex-libra-rdk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-phyflex-fpsc-g-som-temperature.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-phyflex-libra-rdk-bluetooth-88w8987.dtb

dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-verdin-evk.dtb

diff --git a/arch/arm64/boot/dts/freescale/imx95-phyflex-fpsc-g-som-temperature.dtso b/arch/arm64/boot/dts/freescale/imx95-phyflex-fpsc-g-som-temperature.dtso
new file mode 100644
index 000000000000..84afe1ff9f06
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-phyflex-fpsc-g-som-temperature.dtso
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2026 PHYTEC Messtechnik GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+&dram_sense {
+ status = "okay";
+};
+
+&emmc_sense {
+ status = "okay";
+};
+
+&ethphy_sense {
+ status = "okay";
+};
+
+&pmic_sense {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso b/arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso
new file mode 100644
index 000000000000..1601e04b3940
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2026 PHYTEC Messtechnik GmbH
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&lpuart8 {
+ bluetooth {
Can you add label for bluetooth at boards file, so this overlay can
reuse for other 88w8987-bt module.
This would be technically possible, but I don't think it is the cleanest solution.
1. adding an empty bluetooth node into the base dts leads to DTBS_CHECK errors:

arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk.dtb: serial@426a0000 (fsl,imx95-lpuart): bluetooth: 'compatible' is a required property
        from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml
arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk.dtb: serial@426a0000 (fsl,imx95-lpuart): Unevaluated properties are not allowed ('bluetooth', 'uart-has-rtscts' were unexpected)
        from schema $id: http://devicetree.org/schemas/serial/fsl-lpuart.yaml
arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk.dtb: serial@426a0000 (fsl,imx95-lpuart): bluetooth: 'compatible' is a required property
        from schema $id: http://devicetree.org/schemas/serial/serial.yaml

2. I also think this is a bit missleading, as this UART is not used fix for bluetooth on M.2 Key-E, but its default is RS232/RS485. It can be switched to Key-E by the Multiplexer controlled by UART1_BT_RS_SEL GPIO.

The (default) state of this GPIO also needs to  be switched when enabling this overlay. So this leads to the overlay not beeing generic anyway.


+ compatible = "nxp,88w8987-bt";
+ fw-init-baudrate = <115200>;
+ };
+};
+
+&gpio_expander1 {
+ uart1_bt_rs_sel: bt-rs-hog {
+ gpios = <14 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
Look like it is pinmux ref gpio-mux

https://lore.kernel.org/imx/20261023-dxl_lcdif-v4-5-4ae8395a4b23@xxxxxxx/

Looks like a good solution, will do.

Benjamin


Frank
+ line-name = "UART1_BT_RS_SEL";
+ output-high;
+ };
+};

--
2.53.0