Re: [PATCH] arm64: dts: allwinner: h6: taiqicat-a01: Enable Ethernet

From: Jernej Škrabec

Date: Tue Nov 17 2026 - 11:38:02 EST


Dne torek, 17. november 2026 ob 15:21:21 Srednjeevropski standardni čas je Jun Yan napisal(a):
> The TaiqiCat A01 has a 100 Mbit/s Ethernet port, which uses the EPHY
> integrated into the co-packaged AC200 of the Allwinner H6 SoC.
>
> The AC200 derives its 24 MHz reference clock from PWM1, so enable the
> PWM controller and the pwm-clock node that supplies it. Also enable
> I2C3, over which the AC200 is accessed, and describe the AC200 EPHY
> package on the EMAC MDIO bus, with the EMAC operating in RMII mode.
>
> Signed-off-by: Jun Yan <jerrysteve1101@xxxxxxxxx>

Acked-by: Jernej Skrabec <jernej.skrabec@xxxxxxxxx>

Best regards,
Jernej

>
> ---
> The AC200 MFD and EPHY drivers/bindings and the sun50i-h6.dtsi AC200
> description this depends on are already merged in sunxi/dt-for-7.5.
> ---
> .../dts/allwinner/sun50i-h6-taiqicat-a01.dts | 40 +++++++++++++++++++
> 1 file changed, 40 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts
> index 225f42bd3b9e..9b192caeecb2 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts
> @@ -14,6 +14,7 @@ / {
> compatible = "ultrapower,taiqicat-a01", "allwinner,sun50i-h6";
>
> aliases {
> + ethernet0 = &emac;
> ethernet1 = &sdio_wifi;
> serial0 = &uart0;
> };
> @@ -87,6 +88,10 @@ wifi_pwrseq: wifi-pwrseq {
> };
> };
>
> +&ac200_clk {
> + status = "okay";
> +};
> +
> &cpu0 {
> cpu-supply = <&reg_dcdca>;
> };
> @@ -107,6 +112,14 @@ &ehci3 {
> status = "okay";
> };
>
> +&emac {
> + pinctrl-names = "default";
> + pinctrl-0 = <&rmii_pins>;
> + phy-mode = "rmii";
> + phy-handle = <&ac200_ephy>;
> + status = "okay";
> +};
> +
> &gpu {
> mali-supply = <&reg_dcdcc>;
> status = "okay";
> @@ -123,6 +136,29 @@ hdmi_out_con: endpoint {
> };
> };
>
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&mdio {
> + ethernet-phy-package@1 {
> + compatible = "x-powers,ac200-ephy-package";
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + vcc-supply = <&reg_aldo2>;
> + nvmem-cells = <&ephy_calibration>;
> + nvmem-cell-names = "configuration";
> + x-powers,ac200 = <&ac200>;
> + x-powers,xmii-rx-clock-inverted;
> +
> + ac200_ephy: ethernet-phy@1 {
> + compatible = "ethernet-phy-id0044.1400";
> + reg = <1>;
> + };
> + };
> +};
> +
> &mmc0 {
> vmmc-supply = <&reg_cldo1>;
> cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> @@ -173,6 +209,10 @@ &pio {
> vcc-pg-supply = <&reg_bldo3>;
> };
>
> +&pwm {
> + status = "okay";
> +};
> +
> &r_i2c {
> status = "okay";
>
>