[PATCH v2 00/10] arm64: dts: qcom: add LG V60 ThinQ 5G (timelm) support
From: Abdur Rofik
Date: Wed Nov 18 2026 - 07:07:28 EST
This series adds initial mainline device tree and driver support for the
Qualcomm SM8250-based LG V60 ThinQ 5G (timelm / LM-V600) smartphone.
Hardware features supported in this stage:
- Base board devicetree (sm8250-lg-timelm.dts)
- PM8150, PM8150B, PM8150L, and PM8009 PMICs and regulators
- UFS 3.0 storage and MicroSD card slot
- GPIO keys (Volume Down, Google Assistant) and PON keys (Power, Volume Up)
- Simple framebuffer (continuous splash handed off from bootloader)
- Adreno 650 GPU with GMU and zap shader
- LG SW43103 1080x2460 DSI command mode AMOLED panel with DSC
- Silicon Works SW42902 I2C touchscreen controller
- PM8150B USB Type-C controller in sink mode with USB-PD and
orientation switch
- QCA6390 Bluetooth HCI controller on UART6
Changes in v2:
- General / DCO & Identity:
- Replaced account handle "rofikkerneldev" with real name
"Abdur Rofik <rofikcoga@xxxxxxxxx>" across all commit authors,
Signed-off-by trailers, MAINTAINERS entries, and copyright headers
per Documentation/process/submitting-patches.rst.
- Replaced un-documented "lge" vendor prefix with documented "lg"
prefix across devicetree bindings, compatible strings, and dts files.
- Devicetree bindings:
- Added lg,timelm compatible in arm/qcom.yaml.
- Added lg,sw43103 panel binding with enable-gpios and
vddi/vpnl supplies.
- Added lg,sw42902 touchscreen binding with vcl-supply and
vdd-supply.
- Device Tree (arch/arm64/boot/dts/qcom/sm8250-lg-timelm.dts):
- Renamed file to sm8250-lg-timelm.dts matching vendor prefix.
- Reserved memory: folded cont_splash_mem and log regions into base dts;
sorted all nodes by ascending unit-address.
- Ramoops: adjusted size allocations (record-size 0x40000, pmsg-size
0x1c0000) ensuring 256KB is available for dmesg panic dumps.
- Regulators: dropped unused LDO4 from PM8009 regulators-2 node,
resolving the invalid 1.05V constraint failure.
- USB QMP PHY: corrected swapped supplies (vdda-phy to 0.9V l18a_0p9,
vdda-pll to 1.2V l9a_1p2).
- GPU: enabled &gmu alongside &gpu to ensure MSM DRM component
binding succeeds without -ENODEV in a6xx_gmu_init().
- SDHC: added complete pinctrl states (sdc2_default_state,
sdc2_sleep_state, sdc2_card_det_n) to &sdhc_2.
- UFS: added regulator-allow-set-load and regulator-allowed-modes for
dynamic load scaling.
- Panel: added enable-gpios to panel@0 node; sorted display nodes
alphabetically.
- Touchscreen: used fixed regulators reg_ts_vcl and reg_ts_vdd for
power supplies instead of raw GPIO toggles.
- USB Type-C: replaced PDO_BATT with PDO_VAR(5000, 9000, 3000) to
ensure valid 9V/3A PD sink requests without clamping to 600mA;
added OF graph ports connecting DWC3 HS and SuperSpeed QMP PHY
orientation switch.
- Bluetooth: corrected QCA6390 PMU voltages by setting smps6 (0.95V)
and smps8 (1.35V) constraints.
- Cleaned up unused dt-bindings headers and enforced strict
alphabetical ordering of all referenced label nodes.
- Panel driver (drivers/gpu/drm/panel/panel-lg-sw43103.c):
- Removed redundant manual unprepare call in sw43103_remove().
- Guarded sw43103_backlight_update_status() against execution when
unprepared, avoiding unsynchronized DSI DCS writes.
- Removed hardcoded full brightness writes in sw43103_enable().
- Expanded Kconfig help paragraph to 4 lines.
- Touchscreen driver (drivers/input/touchscreen/sw42902.c):
- Converted GPIO power controls to standard regulator bulk supplies
(vcl and vdd).
- Added suspended flag guarding resume and I2C operations to prevent
IRQ disable imbalance on resume error.
- Pre-scanned for palm touch reports before queueing MT slots.
- Used named initializer in struct i2c_device_id table.
- Followed input subsystem error naming conventions.
- MAINTAINERS:
- Added entries for LG V60 ThinQ 5G, LG SW43103 panel driver, and
Silicon Works SW42902 touchscreen driver in strict alphabetical
order.
Abdur Rofik (10):
dt-bindings: arm: qcom: add LG V60 ThinQ 5G (timelm)
arm64: dts: qcom: add LG V60 ThinQ 5G (timelm) support
dt-bindings: display: panel: add LG SW43103
drm/panel: add LG SW43103 panel driver
dt-bindings: input: touchscreen: add Silicon Works SW42902
Input: touchscreen: add Silicon Works SW42902 support
arm64: dts: qcom: sm8250-lg-timelm: enable SW43103 panel
arm64: dts: qcom: sm8250-lg-timelm: add SW42902 touchscreen
arm64: dts: qcom: sm8250-lg-timelm: enable USB Type-C
arm64: dts: qcom: sm8250-lg-timelm: add QCA6390 Bluetooth
.../devicetree/bindings/arm/qcom.yaml | 1 +
.../bindings/display/panel/lg,sw43103.yaml | 69 ++
.../input/touchscreen/lg,sw42902.yaml | 73 ++
MAINTAINERS | 19 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8250-lg-timelm.dts | 840 ++++++++++++++++++
drivers/gpu/drm/panel/Kconfig | 13 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-lg-sw43103.c | 587 ++++++++++++
drivers/input/touchscreen/Kconfig | 13 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/sw42902.c | 355 ++++++++
12 files changed, 1973 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml
create mode 100644 arch/arm64/boot/dts/qcom/sm8250-lg-timelm.dts
create mode 100644 drivers/gpu/drm/panel/panel-lg-sw43103.c
create mode 100644 drivers/input/touchscreen/sw42902.c
--
2.39.5