[PATCH 2/6] drm/msm/a6xx: Don't fail GMU resume if the GPU init regs SCM call is absent

From: Puranam V G Tejaswi

Date: Wed Nov 18 2026 - 08:09:00 EST


On A750, A753 and A8xx, a6xx_gmu_secure_init() asks the secure world to
program CX_MISC_SW_FUSE_VALUE through qcom_scm_gpu_init_regs(), and
aborts the GMU resume if that call fails.

Some platforms have a secure world that does not implement this call.
The call fails every time and the GPU never powers up. The fuse
register is still protected from the kernel, so the driver cannot
program it directly either.

If the secure world does not support the call, skip it, but still read
the fuse register back. An earlier boot stage may have programmed it,
and the features it enables, such as raytracing, are then reported
correctly. If nothing programmed it, they stay disabled. Log once when
the call is skipped.

Signed-off-by: Puranam V G Tejaswi <puranam.tejaswi@xxxxxxxxxxxxxxxx>
---
drivers/gpu/drm/msm/adreno/a6xx_gmu.c | 27 ++++++++++++++++++---------
1 file changed, 18 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/msm/adreno/a6xx_gmu.c b/drivers/gpu/drm/msm/adreno/a6xx_gmu.c
index 0fa2d2091f3e..95636dabee38 100644
--- a/drivers/gpu/drm/msm/adreno/a6xx_gmu.c
+++ b/drivers/gpu/drm/msm/adreno/a6xx_gmu.c
@@ -1249,22 +1249,31 @@ static int a6xx_gmu_secure_init(struct a6xx_gpu *a6xx_gpu)
goto done;
}

- u32 gpu_req = QCOM_SCM_GPU_ALWAYS_EN_REQ | QCOM_SCM_GPU_TSENSE_EN_REQ;
+ /*
+ * Some secure world implementations do not provide this call.
+ * Skip it then. An earlier boot stage may still have
+ * programmed the fuse register, so read it back either way.
+ */
+ if (qcom_scm_gpu_init_regs_is_available()) {
+ u32 gpu_req = QCOM_SCM_GPU_ALWAYS_EN_REQ |
+ QCOM_SCM_GPU_TSENSE_EN_REQ;

- if (adreno_gpu->info->a6xx->clx_tbl)
- gpu_req |= QCOM_SCM_GPU_CLX_EN_REQ;
+ if (adreno_gpu->info->a6xx->clx_tbl)
+ gpu_req |= QCOM_SCM_GPU_CLX_EN_REQ;

- ret = qcom_scm_gpu_init_regs(gpu_req);
- if (ret) {
- dev_warn_once(gpu->dev->dev,
- "SCM call failed\n");
- return ret;
+ ret = qcom_scm_gpu_init_regs(gpu_req);
+ if (ret) {
+ dev_warn_once(gpu->dev->dev, "SCM call failed\n");
+ return ret;
+ }
+ } else {
+ dev_info_once(gpu->dev->dev, "GPU init regs SCM call not available, skipping\n");
}

/*
* On A7XX_GEN3 and newer, raytracing may be disabled by the
* firmware, find out whether that's the case. The scm call
- * above sets the fuse register.
+ * above, or an earlier boot stage, sets the fuse register.
*/
fuse_val = a6xx_cx_misc_read(a6xx_gpu,
REG_A7XX_CX_MISC_SW_FUSE_VALUE);

--
2.34.1