[PATCH wireless-next v2] wifi: brcmfmac: turn off TX beamforming on Apple BCM4364

From: Andre Eikmeyer

Date: Wed Nov 18 2026 - 09:12:08 EST


brcmfmac sets "txbf" to 1 at init. The Apple firmware for the BCM4364
(9.30.514.0.32.5.94 on the MacBookPro15,1) has it on by default as
well, and then rate control settles on a single beamformed spatial
stream (nrate VHT MCS9 NSS1 TXBF) towards a two stream AP.

Beamforming more than one stream does not work on this firmware. With
"txbf" on and the rate fixed to two or three streams, the firmware takes
the rate but the uplink stalls. With "txbf" off, rate control picks two
streams (VHT MCS9 NSS2) on its own.

Uplink measured with iperf3 against a wired server was:

0.5 m from the AP, -36 dBm: 351 -> 623 Mbit/s
-70 dBm: 96-130 -> 149-175 Mbit/s

Downlink and latency remain unchanged.

Set "txbf" to 0 on the BCM4364 when the board type is an Apple one.

Tested-by: Yossef Osman <Yossef.Osman@xxxxxxxxx>
Tested-by: Aditya Garg <aditya.garg@xxxxxxxxx>
Signed-off-by: Andre Eikmeyer <dev@deq.rocks>
---
Changes in v2:
- Restrict the quirk to Apple boards with settings->board_type
- Spell out the txbf value with an explicit if and fix the comment
- State the cause. Beamforming more than one stream does not work
- Fix the typo
- Target wireless-next
- v1: https://lore.kernel.org/all/20261104151623.70695-1-dev@deq.rocks/

The T2 Linux community runs this patch with its kernels for quite a while
now, no regression was reported.

.../wireless/broadcom/brcm80211/brcmfmac/common.c | 15 +++++++++++++--
1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
index 93458c2fbc2e..f8ff6217de16 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
@@ -10,6 +10,7 @@
#include <linux/firmware.h>
#include <brcmu_wifi.h>
#include <brcmu_utils.h>
+#include <brcm_hw_ids.h>
#include "core.h"
#include "bus.h"
#include "debug.h"
@@ -275,6 +276,7 @@ int brcmf_c_preinit_dcmds(struct brcmf_if *ifp)
struct brcmf_rev_info *ri;
char *clmver;
char *ptr;
+ s32 txbf;
s32 err;

if (is_valid_ether_addr(ifp->mac_addr)) {
@@ -432,8 +434,17 @@ int brcmf_c_preinit_dcmds(struct brcmf_if *ifp)
goto done;
}

- /* Enable tx beamforming, errors can be ignored (not supported) */
- (void)brcmf_fil_iovar_int_set(ifp, "txbf", 1);
+ /* Enable tx beamforming, errors can be ignored (not supported).
+ * The Apple firmware for the BCM4364 has it on by default and then
+ * beamforms a single spatial stream, as beamforming more than one
+ * stream does not work. Turn it off there, so two streams are used.
+ */
+ txbf = 1;
+ if (drvr->bus_if->chip == BRCM_CC_4364_CHIP_ID &&
+ drvr->settings->board_type &&
+ strstarts(drvr->settings->board_type, "apple,"))
+ txbf = 0;
+ (void)brcmf_fil_iovar_int_set(ifp, "txbf", txbf);
done:
return err;
}

base-commit: 5dbf2415ca9821a611d09308e3b29d2c37e7cd77
--
2.56.0