[PATCH 2/2] iio: adc: rohm-bd79112: Support ROHM BD79111

From: Matti Vaittinen

Date: Wed Nov 18 2026 - 09:19:53 EST


From: Matti Vaittinen <mazziesaccount@xxxxxxxxx>

ROHM BD79111 is very similar to the BD79112. Both are ADC/GPIO devices,
where pins can be configured to be either used as GPIO or ADC inputs.
ADCs are 12-bit SAR ADCs and GPIOs support input/output but not being IRQ
sources.

The main difference is amount of channels/GPIOs. The BD79112 has 32 pins
for this use, the BD79111 has 16. Furthermore, the BD79111 data-sheet
promises 0.5 MSPS sample rate with maximum of 10 MHz SPI clock, whereas
the BD79112 data-sheet mentioned 1MSPS rate with maximum of 20 MHz SPI
clock.

NOTE: In order to achieve those speeds one needs to use more optimized
protocol compared to the one implemented in this driver. This driver
retrieves samples using two 16-bit SPI transactions. The first
transaction writes the channel to be sampled, and ignores data on MISO.
Then the next 16-bit transaction carries the data.

Achieving maximum sample-rate would require the driver to interpret the
MISO data of each 16-bit transaction so, that when the
channel-to-be-sampled was sent in transaction N, the data is read at
transaction N+1 - which also already configures the channel to be
sampled for transaction N+2. Supporting this would require the
channel-to-be-read for the future read to be known when the current
channel data is retrieved. For raw-reads this is not possible and for
buffered reads it would make things a bit hairy.

So, here we aim for simplicity instead of the peak performance.

Signed-off-by: Matti Vaittinen <mazziesaccount@xxxxxxxxx>
---
drivers/iio/adc/Kconfig | 9 +--
drivers/iio/adc/rohm-bd79112.c | 113 +++++++++++++++++++++++++++------
2 files changed, 98 insertions(+), 24 deletions(-)

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index a802d8ee4dd9..db9e0a0713e1 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -1516,14 +1516,15 @@ config RN5T618_ADC
will be called rn5t618-adc.

config ROHM_BD79112
- tristate "Rohm BD79112 ADC driver"
+ tristate "ROHM BD79112 and BD79111 ADC/GPIO driver"
depends on SPI && GPIOLIB
select REGMAP_SPI
select IIO_ADC_HELPER
help
- Say yes here to build support for the ROHM BD79112 ADC. The
- ROHM BD79112 is a 12-bit, 32-channel, SAR ADC. Analog inputs
- can also be used for GPIO.
+ Say yes here to build support for the ROHM BD79112 and BD79111
+ ADCs. Both of the ICs are 12-bit SAR ADCs. The ROHM BD79112 has
+ 32-channels, the BD79111 has 16. Analog inputs can also be used
+ for GPIO.

config ROHM_BD79124
tristate "Rohm BD79124 ADC driver"
diff --git a/drivers/iio/adc/rohm-bd79112.c b/drivers/iio/adc/rohm-bd79112.c
index 2506fec7be84..604c6ccafb4f 100644
--- a/drivers/iio/adc/rohm-bd79112.c
+++ b/drivers/iio/adc/rohm-bd79112.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-only
/*
- * ROHM ADC driver for BD79112 signal monitoring hub.
+ * ROHM ADC driver for BD79111 and BD79112 signal monitoring hubs.
* Copyright (C) 2025, ROHM Semiconductor.
*
* SPI communication derived from ad7923.c and ti-ads7950.c
@@ -26,7 +26,17 @@

#define BD79112_MAX_NUM_CHANNELS 32

+struct bd79112_data;
+
+struct bd7911x_chip_data {
+ const char *name;
+ const char * const *chan_names;
+ unsigned int num_channels;
+ int (*init_disable_gpios)(struct bd79112_data *data);
+};
+
struct bd79112_data {
+ const struct bd7911x_chip_data *cd;
struct spi_device *spi;
struct regmap *map;
struct device *dev;
@@ -369,7 +379,6 @@ static int bd79112_gpio_output(struct gpio_chip *gc, unsigned int offset,
}

static const struct gpio_chip bd79112_gpio_chip = {
- .label = "bd79112-gpio",
.get_direction = bd79112_gpio_dir_get,
.direction_input = bd79112_gpio_input,
.direction_output = bd79112_gpio_output,
@@ -378,20 +387,20 @@ static const struct gpio_chip bd79112_gpio_chip = {
.set_multiple = bd79112_gpio_set_multiple,
.init_valid_mask = bd79112_gpio_init_valid_mask,
.can_sleep = true,
- .ngpio = 32,
.base = -1,
};

-static unsigned int bd79112_get_gpio_pins(const struct iio_chan_spec *cs, int num_channels)
+static unsigned int bd79112_get_gpio_pins(const struct iio_chan_spec *cs,
+ int num_channels, int max_channels)
{
unsigned int i, gpio_channels;

/*
- * Let's initialize the mux config to say that all 32 channels are
+ * Let's initialize the mux config to say that all channels are
* GPIOs. Then we can just loop through the iio_chan_spec and clear the
* bits for found ADC channels.
*/
- gpio_channels = GENMASK(31, 0);
+ gpio_channels = GENMASK(max_channels - 1, 0);
for (i = 0; i < num_channels; i++)
gpio_channels &= ~BIT(cs[i].channel);

@@ -410,6 +419,61 @@ static const char * const bd79112_chan_names[] = {
"AGIO12B", "AGIO13B", "AGIO14B", "AGIO15B", /* 28 - 31 */
};

+static int bd79112_disable_gpios(struct bd79112_data *data)
+{
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < BD79112_NUM_GPIO_EN_REGS; i++) {
+ ret = regmap_write(data->map, BD79112_FIRST_GPIO_EN_REG + i, 0);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+/* The BD79111 only has the registers for pins 0 - 15 */
+static int bd79111_disable_gpios(struct bd79112_data *data)
+{
+ static const unsigned int regs[] = {
+ BD79112_REG_GPI_EN_A8_A15, BD79112_REG_GPI_EN_A0_A7,
+ BD79112_REG_GPO_EN_A8_A15, BD79112_REG_GPO_EN_A0_A7,
+ };
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < ARRAY_SIZE(regs); i++) {
+ ret = regmap_write(data->map, regs[i], 0);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+/* The BD79111 channel names as in the data-sheet */
+static const char * const bd79111_chan_names[] = {
+ "AGIO0", "AGIO1", "AGIO2", "AGIO3", /* 0 - 3 */
+ "AGIO4", "AGIO5", "AGIO6", "AGIO7", /* 4 - 7 */
+ "AGIO8", "AGIO9", "AGIO10", "AGIO11", /* 8 - 11 */
+ "AGIO12", "AGIO13", "AGIO14", "AGIO15", /* 12 - 15 */
+};
+
+static const struct bd7911x_chip_data bd79111_chip_data = {
+ .name = "bd79111",
+ .chan_names = bd79111_chan_names,
+ .num_channels = 16,
+ .init_disable_gpios = bd79111_disable_gpios,
+};
+
+static const struct bd7911x_chip_data bd79112_chip_data = {
+ .name = "bd79112",
+ .chan_names = bd79112_chan_names,
+ .num_channels = 32,
+ .init_disable_gpios = bd79112_disable_gpios,
+};
+
static int bd79112_probe(struct spi_device *spi)
{
struct bd79112_data *data;
@@ -425,6 +489,10 @@ static int bd79112_probe(struct spi_device *spi)
return -ENOMEM;

data = iio_priv(iio_dev);
+ data->cd = spi_get_device_match_data(spi);
+ if (!data->cd)
+ return -ENODEV;
+
data->spi = spi;
data->dev = dev;
data->map = devm_regmap_init(dev, NULL, data, &bd79112_regmap);
@@ -462,7 +530,7 @@ static int bd79112_probe(struct spi_device *spi)
"Failed to optimize SPI write message\n");

ret = devm_iio_adc_device_alloc_chaninfo_se(dev, &bd79112_chan_template,
- BD79112_MAX_NUM_CHANNELS - 1,
+ data->cd->num_channels - 1,
&cs);

/* Register all pins as GPIOs if there are no ADC channels */
@@ -476,10 +544,10 @@ static int bd79112_probe(struct spi_device *spi)
iio_dev->channels = cs;

for (i = 0; i < iio_dev->num_channels; i++)
- cs[i].datasheet_name = bd79112_chan_names[cs[i].channel];
+ cs[i].datasheet_name = data->cd->chan_names[cs[i].channel];

iio_dev->info = &bd79112_info;
- iio_dev->name = "bd79112";
+ iio_dev->name = data->cd->name;
iio_dev->modes = INDIO_DIRECT_MODE;

/*
@@ -488,12 +556,9 @@ static int bd79112_probe(struct spi_device *spi)
* without having to worry about some pins being initially used for
* GPIO.
*/
- for (i = 0; i < BD79112_NUM_GPIO_EN_REGS; i++) {
- ret = regmap_write(data->map, BD79112_FIRST_GPIO_EN_REG + i, 0);
- if (ret)
- return dev_err_probe(dev, ret,
- "Failed to initialize channels\n");
- }
+ ret = data->cd->init_disable_gpios(data);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to initialize channels\n");

ret = devm_iio_device_register(data->dev, iio_dev);
if (ret)
@@ -501,14 +566,15 @@ static int bd79112_probe(struct spi_device *spi)

register_gpios:
gpio_pins = bd79112_get_gpio_pins(iio_dev->channels,
- iio_dev->num_channels);
+ iio_dev->num_channels,
+ data->cd->num_channels);

/* If all channels are reserved for ADC, then we're done. */
if (!gpio_pins)
return 0;

/* Default all the GPIO pins to GPI */
- for_each_set_bit(pin, &gpio_pins, BD79112_MAX_NUM_CHANNELS) {
+ for_each_set_bit(pin, &gpio_pins, data->cd->num_channels) {
ret = bd79112_gpio_dir_set(data, pin, GPIO_LINE_DIRECTION_IN);
if (ret)
return dev_err_probe(dev, ret,
@@ -518,18 +584,25 @@ static int bd79112_probe(struct spi_device *spi)
data->gpio_valid_mask = gpio_pins;
data->gc = bd79112_gpio_chip;
data->gc.parent = dev;
+ data->gc.ngpio = data->cd->num_channels;
+ data->gc.label = devm_kasprintf(dev, GFP_KERNEL, "%s-gpio",
+ data->cd->name);
+ if (!data->gc.label)
+ return -ENOMEM;

return devm_gpiochip_add_data(dev, &data->gc, data);
}

static const struct of_device_id bd79112_of_match[] = {
- { .compatible = "rohm,bd79112" },
+ { .compatible = "rohm,bd79111", .data = &bd79111_chip_data },
+ { .compatible = "rohm,bd79112", .data = &bd79112_chip_data },
{ }
};
MODULE_DEVICE_TABLE(of, bd79112_of_match);

static const struct spi_device_id bd79112_id[] = {
- { .name = "bd79112" },
+ { .name = "bd79111", .driver_data = (kernel_ulong_t)&bd79111_chip_data },
+ { .name = "bd79112", .driver_data = (kernel_ulong_t)&bd79112_chip_data },
{ }
};
MODULE_DEVICE_TABLE(spi, bd79112_id);
@@ -545,6 +618,6 @@ static struct spi_driver bd79112_driver = {
module_spi_driver(bd79112_driver);

MODULE_AUTHOR("Matti Vaittinen <mazziesaccount@xxxxxxxxx>");
-MODULE_DESCRIPTION("Driver for ROHM BD79112 ADC/GPIO");
+MODULE_DESCRIPTION("Driver for ROHM BD79111 and BD79112 ADC/GPIO");
MODULE_LICENSE("GPL");
MODULE_IMPORT_NS("IIO_DRIVER");
--
2.56.1

Attachment: signature.asc
Description: PGP signature