Re: [PATCH v3 2/2] arm64: dts: qcom: talos-lyra-evk: Wire up CYPD6129 USB Type-C ports
From: Dmitry Baryshkov
Date: Wed Nov 18 2026 - 09:40:45 EST
On Mon, Nov 16, 2026 at 05:36:23PM +0530, Akash Kumar wrote:
> From: Akash Kumar <akakum@xxxxxxxxxxxxxxxx>
>
> Add the CYPD6129 UCSI PD controller (typec@40) on i2c5 with its two
> USB-C connectors, and route their HS/SS endpoints to usb_1/usb_2's
> dwc3 controllers and the USB QMP PHY. The PD controller, its GPIO86
> interrupt line, and the PM8150 GPIO10 VBUS-enable control are on the
> SoC/SoM card, so they are added to talos-lyra-evk-som.dtsi.
>
> connector@1 additionally routes its SBU lines through a GPIO-controlled
> SBU mux (onnn,fsusb43l10x) selected by expander0, since connector@1's
> physical Type-C port carries SuperSpeed and SBU while connector@0's
> port is USB-HS-only by hardware design. The SBU mux and its GPIO
> expanders live on the carrier board, so they are added to
> talos-lyra-evk.dts along with the TLMM GPIO64 VBUS boost enable fixed
> regulator that supplies the USB daughter-card connector's VBUS.
Thanks!
>
> Switch usb_1/usb_2 to dr_mode = "otg" with usb-role-switch so role
> switching is driven by the PD controller, and add the supporting
> USB1_VBUS regulator and pinctrl entries needed by this routing.
>
> Signed-off-by: Akash Kumar <akakum@xxxxxxxxxxxxxxxx>
> ---
> .../boot/dts/qcom/talos-lyra-evk-som.dtsi | 121 ++++++++++++++++++
> arch/arm64/boot/dts/qcom/talos-lyra-evk.dts | 42 ++++--
> 2 files changed, 152 insertions(+), 11 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-som.dtsi b/arch/arm64/boot/dts/qcom/talos-lyra-evk-som.dtsi
> index 7d9a08471906..ed3a369dac02 100644
> --- a/arch/arm64/boot/dts/qcom/talos-lyra-evk-som.dtsi
> +++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-som.dtsi
> @@ -31,6 +31,16 @@ xo_board_clk: xo-board-clk {
> #clock-cells = <0>;
> };
> };
> +
> + regulator-usb1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "USB1_VBUS";
> + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&usb1_en>;
> + pinctrl-names = "default";
> + enable-active-high;
> + regulator-always-on;
> + };
> };
>
> &apps_rsc {
> @@ -179,6 +189,87 @@ &gpu_zap_shader {
> firmware-name = "qcom/qcs615/a612_zap.mbn";
> };
>
> +&i2c5 {
> + typec@40 {
> + compatible = "cypress,cypd6129";
> + reg = <0x40>;
> + interrupts-extended = <&tlmm 86 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-0 = <&usb0_intr_state>;
> + pinctrl-names = "default";
> + wakeup-source;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
Does it mean that the connector is present on the SoM? The CYPD might be
a part of the SoM, but I guess that connectors are a part of the carrier
board (and might differ on other carrier boards).
> + compatible = "usb-c-connector";
> + reg = <0>;
> + label = "USB-C";
> + data-role = "dual";
> + power-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + ucsi_ccg_port_0_hs: endpoint {
> + remote-endpoint = <&usb_2_dwc3_hs>;
> + };
> + };
> + };
> + };
> +
> + connector@1 {
> + compatible = "usb-c-connector";
> + reg = <1>;
> + label = "USB-C";
> + data-role = "dual";
> + power-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + ucsi_ccg_port_1_hs: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + ccg_typec_con1_ss: endpoint {
> + remote-endpoint = <&usb_qmpphy_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> +
> + ccg_typec_con1_sbu: endpoint {
> + remote-endpoint = <&sbu_mux_in>;
> + };
This line confirms, please move connector nodes to the carrier board
DTS.
> + };
> + };
> + };
> + };
> +};
> +
> +&pm8150_gpios {
> + usb1_en: usb1-en-state {
> + pins = "gpio10";
> + function = "normal";
> + output-enable;
> + power-source = <0>;
> + };
> +};
> +
> &qupv3_id_0 {
> status = "okay";
> };
> @@ -229,6 +320,15 @@ &sdhc_2 {
> status = "okay";
> };
>
> +&tlmm {
> + usb0_intr_state: usb0-intr-state {
> + pins = "gpio86";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +};
> +
> &uart0 {
> status = "okay";
> };
> @@ -250,6 +350,14 @@ &ufs_mem_phy {
> status = "okay";
> };
>
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&ucsi_ccg_port_1_hs>;
> +};
These endpoint wiring must go to the EVK DTSI.
> +
> &usb_1_hsphy {
> vdd-supply = <&vreg_l5a>;
> vdda-pll-supply = <&vreg_l12a>;
> @@ -258,6 +366,15 @@ &usb_1_hsphy {
> status = "okay";
> };
>
> +&usb_2 {
> + status = "okay";
> +};
> +
> +/* HS only */
> +&usb_2_dwc3_hs {
> + remote-endpoint = <&ucsi_ccg_port_0_hs>;
> +};
> +
> &usb_2_hsphy {
> vdd-supply = <&vreg_l5a>;
> vdda-pll-supply = <&vreg_l12a>;
> @@ -279,3 +396,7 @@ &usb_qmpphy_2 {
>
> status = "okay";
> };
> +
> +&usb_qmpphy_out {
> + remote-endpoint = <&ccg_typec_con1_ss>;
> +};
> diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
> index d4468e609911..020ce7db4241 100644
> --- a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
> +++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
> @@ -4,6 +4,7 @@
> */
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include "talos-lyra-evk-som.dtsi"
>
> / {
> @@ -22,6 +23,30 @@ dp0_connector_in: endpoint {
> };
> };
> };
> +
> + regulator-vbus-boost-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_vbus_boost_5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&tlmm 64 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&vbus_boost_en>;
> + pinctrl-names = "default";
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + sbu-mux {
> + compatible = "onnn,fsusb43l10x", "gpio-sbu-mux";
> + select-gpios = <&expander0 12 GPIO_ACTIVE_LOW>;
Missing pinctrl.
> + orientation-switch;
> +
> + port {
> + sbu_mux_in: endpoint {
> + remote-endpoint = <&ccg_typec_con1_sbu>;
> + };
> + };
> + };
> };
>
> &i2c5 {
> @@ -100,16 +125,11 @@ dp_hot_plug_det: dp-hot-plug-det-state {
> function = "dp_hot";
> bias-disable;
> };
> -};
>
> -&usb_1 {
> - dr_mode = "peripheral";
> -
> - status = "okay";
> -};
> -
> -&usb_2 {
> - dr_mode = "host";
> -
> - status = "okay";
> + vbus_boost_en: vbus-boost-en-state {
> + pins = "gpio64";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> };
> --
> 2.43.0
>
--
With best wishes
Dmitry