Hi,
Just built 2.3.51 (if you just read my previous message, I built it
without parallel port support this time), and had this problem:
[1.] One line summary of the problem:
mount doesn't recognize my superblock, at least the first time it tried
[2.] Full description of the problem/report:
On bootup, mount would not recognize my root partition and refused to
mount it. I rebuilt the kernel and tried again, and it hasn't failed yet.
I had accidentally deleted my .config, so I don't know if I changed
something inadvertently the second build. (Sorry!!!) Specifically, I
don't remember if I inadvertently left plug and play support enabled on
the first try. I'll test with plug and play and repost if it reproduces
the problem.
Disk is IDE, not SCSI, on primary master on-board IDE controller. dmesg
says:
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 40MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST33210A, ATA DISK drive
hdb: ATAPI CDROM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ST33210A, 3098MB w/256kB Cache, CHS=787/128/63, UDMA(33)
hdb: ATAPI 44X CD-ROM drive, 128kB Cache
and hda is, of course, the device in question.
[3.] Keywords (i.e., modules, networking, kernel):
mount, ide
[4.] Kernel version (from /proc/version):
Linux version 2.3.51 (root@walker1-83) (gcc version 2.95.2 20000220
(Debian GNU/Linux)) #2 Sun Mar 12 08:12:08 CST 2000
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
N/A
[6.] A small shell script or example program which triggers the
problem (if possible)
I can't repeat this problem.
[7.] Environment
x86
[7.1.] Software (add the output of the ver_linux script here)
-- Versions installed: (if some fields are empty or look
-- unusual then possibly you have very old versions)
Linux walker1-83 2.3.51 #2 Sun Mar 12 08:12:08 CST 2000 i586 unknown
Kernel modules 2.3.9
Gnu C 2.95.2
Binutils 2.9.5.0.22
Linux C Library 2.1.3
Dynamic linker ldd: version 1.9.11
Procps 2.0.6
Mount 2.10f
Net-tools 2.05
Kbd 0.99
Sh-utils 2.0
Modules Loaded
[7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : AuthenticAMD
cpu family : 5
model : 8
model name : AMD-K6(tm) 3D processor
stepping : 12
cpu MHz : 350.801757
fdiv_bug : no
hlt_bug : no
sep_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr mce cx8 sep mtrr pge mmx 3dnow
bogomips : 699.60
[7.3.] Module information (from /proc/modules):
N/A
[7.4.] SCSI information (from /proc/scsi/scsi)
SCSI support is not compiled into the kernel
[7.5.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
Some .config as my previous post except minus the parallel port stuff. (I
turned off all parallel port stuff at all.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Wed Mar 15 2000 - 21:00:21 EST