[1.] Kernel 2.4.0-test7 hangs when heavy load is produced on the EXT2
filesystem on a Compaq SMART/2 RAID array.
[2.] The problem occurs to 99 percent when unpacking a tar file (here it
was the SAMBA-2.0.7 package and also the installation of StarOffice 5.2).
It seems that especially creating lots of small files causes this behaviour
whereas copying one 600 MB file works without any problems. The hang
doesn't occur directly when writing the files but a little later when a
read operation is performed (may be only when this read is from the same
filesystem - i couldn't really ensure this).
[3.] ext2-filesystem, compaq smart/2 array, compaq ProLiant1850R
[4.]
Linux version 2.4.0-test7 (root@tuxtest.1sp1.rsd.de) (gcc version
egcs-2.91.66 19990314 (egcs-1.1.2 release)) #2 SMP Wed Sep 6 18:54:57 CEST
2000
[5.] No OOPS message produced. Kernel hangs without messages (no OOPS, no
entry in "messages"-file, etc.)
[6.] Unpack a big tar-archive to a ext2 filesystem and do a serveral read
operations afterwards.
[7.1.] Software. Following the output of "ver_linux":
-- Versions installed: (if some fields are empty or look
-- unusual then possibly you have very old versions)
Linux tuxtest.1sp1.rsd.de 2.4.0-test7 #2 SMP Wed Sep 6 18:54:57 CEST 2000 i686 unknown
Kernel modules 2.1.121
Gnu C egcs-2.91.66
Binutils 2.9.5.0.16
Linux C Library 2.1.3
Dynamic linker ldd: version 1.9.11
Linux C++ Library 2.9.0
Procps 2.0.2
Mount 2.9s
Net-tools 1.52
Kbd 0.99
Sh-utils 1.16
Modules Loaded
[7.2.] Processor information:
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 7
model name : Pentium III (Katmai)
stepping : 3
cpu MHz : 548.345941
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
sep_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr xmm
bogomips : 1094.45
[7.3.] Module information: No modules loaded. Kernel "hard wired".
[7.4.] Driver and Hardware-Info:
/proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
1000-10ff : Symbios Logic Inc. (formerly NCR) 53c875
1400-14ff : Symbios Logic Inc. (formerly NCR) 53c875 (#2)
1800-18ff : Compaq Computer Corporation Advanced System Management Controller
1c00-1c1f : Intel Corporation 82371AB PIIX4 USB
2000-20ff : ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC]
2400-240f : Compaq Computer Corporation ProLiant Integrated Netelligent 10/100
2400-240f : TLAN
2410-241f : Compaq Computer Corporation Netelligent 10/100
2410-241f : TLAN
3000-3fff : PCI Bus #01
3000-30ff : Compaq Computer Corporation Smart-2/P RAID Controller
f000-f03f : Intel Corporation 82371AB PIIX4 ACPI
f040-f05f : Intel Corporation 82371AB PIIX4 ACPI
f100-f10f : Intel Corporation 82371AB PIIX4 IDE
/proc/iomem
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cbfff : Extension ROM
000f0000-000fffff : System ROM
00100000-27ffbfff : System RAM
00100000-0028dca7 : Kernel code
0028dca8-002a939f : Kernel data
27ffc000-27ffffff : ACPI Tables
28000000-280000ff : Symbios Logic Inc. (formerly NCR) 53c875
28000100-280001ff : Symbios Logic Inc. (formerly NCR) 53c875 (#2)
28001000-28001fff : Symbios Logic Inc. (formerly NCR) 53c875
28002000-28002fff : Symbios Logic Inc. (formerly NCR) 53c875 (#2)
c5000000-c5ffffff : ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC]
c6bfeee0-c6bfeeef : Compaq Computer Corporation Netelligent 10/100
c6bfeef0-c6bfeeff : Compaq Computer Corporation ProLiant Integrated Netelligent 10/100
c6bfef00-c6bfefff : Compaq Computer Corporation Advanced System Management Controller
c6bff000-c6bfffff : ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC]
c6c00000-c6dfffff : FORE Systems Inc PCA-200E
c6f00000-c6ffffff : PCI Bus #01
c6ffff00-c6ffffff : Compaq Computer Corporation Smart-2/P RAID Controller
fec00000-fec0ffff : reserved
fee00000-fee0ffff : reserved
fff80000-ffffffff : reserved
[7.5.] PCI-Information:
(See attached file: pciinfo.txt)
[7.6.] SCSI-Information:
SCSI not installed (Controller available but not used and no kernel driver
present!)
[7.7.]
The filesystem I discoverd the bug on was mounted as "/usr". Kernel
compiling in "/usr/src/linux" never hung the system but unpacking a simple
tar/tgz did ??!??
ATM-Drivers are activated (for FORE PCA-200E card) but the bug occurs also
with the "normal" TI-Thunderlan driver activated. It seems to be
independent from the network functionality.
Quota is enabled but not for the "/" partition and the "/usr" partition
where the bug took place. But there is one message during quota
initialization (when system boots up) that could effect the bug. It is:
Sep 11 14:42:27 tuxtest kernel: bug: kernel timer added twice at c01b6808.
Sep 11 14:43:57 tuxtest kernel: bug: kernel timer added twice at c01b6808.
Sep 11 14:44:11 tuxtest kernel: bug: kernel timer added twice at c01b6808.
The number of these messages differs each system startup (and quota init). In the running system the messages never return.
I hope I did everything right with this bug report, it's my first one...
I'am open to test every change to the kernel on our ProLiant 1850R system
as it is not in our production network at the moment but in test state.
Thank you all very much for making LINUX that pretty good system that it
is.
Kurt Stempina
Rohde&Schwarz GmbH
Department 1SP1
Muehldorfstrasse 15
D - 81671 Munich
Germany
Phone: ++49 4129 12505
Fax: ++49 4129 11674
E-Mail: kurt.stempina@rsd.rohde-schwarz.com
Last some addtional /proc infos that could eventually help you:
/proc/meminfo
total: used: free: shared: buffers: cached:
Mem: 658067456 28753920 629313536 0 618496 17465344
Swap: 325869568 17403904 308465664
MemTotal: 642644 kB
MemFree: 614564 kB
MemShared: 0 kB
Buffers: 604 kB
Cached: 17056 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 642644 kB
LowFree: 614564 kB
SwapTotal: 318232 kB
SwapFree: 301236 kB
/proc/locks
1: POSIX ADVISORY WRITE 585 48:01:123386 0 9223372036854775807 e3625d40 c0294d00 e362513c 00000000 e3625d4c
2: POSIX ADVISORY WRITE 586 48:01:51610 0 9223372036854775807 e3625138 e3625d44 e3625efc 00000000 e36250ec
2: -> POSIX ADVISORY WRITE 587 48:01:51610 0 9223372036854775807 e36250e0 e3625244 c0294d08 e3625138 e362524c
2: -> POSIX ADVISORY WRITE 588 48:01:51610 0 9223372036854775807 e3625240 e362534c e36250e4 e3625138 e3625354
2: -> POSIX ADVISORY WRITE 589 48:01:51610 0 9223372036854775807 e3625348 e3625454 e3625244 e3625138 e362545c
2: -> POSIX ADVISORY WRITE 591 48:01:51610 0 9223372036854775807 e3625450 c0294d08 e362534c e3625138 e3625144
3: POSIX ADVISORY WRITE 482 48:01:51603 0 9223372036854775807 e3625ef8 e362513c e3625fac 00000000 e3625f04
4: FLOCK ADVISORY WRITE 466 48:01:51602 0 9223372036854775807 e3625fa8 e3625efc e3625e4c 00000000 e3625fb4
5: POSIX ADVISORY READ 447 48:01:119417 0 9223372036854775807 e3625e48 e3625fac e3625f54 00000000 e3625e54
6: POSIX ADVISORY WRITE 446 48:01:51600 0 9223372036854775807 e3625f50 e3625e4c c0294d00 00000000 e3625f5c
/proc/partitions
major minor #blocks name
72 0 8882160 ida/c0d0
72 1 983280 ida/c0d0p1
72 2 7543920 ida/c0d0p2
72 3 36704 ida/c0d0p3
72 4 318240 ida/c0d0p4
72 16 88911360 ida/c0d1
72 17 22031984 ida/c0d1p1
72 18 22848000 ida/c0d1p2
Output of "df" command:
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/ida/c0d0p1 951360 382812 519384 42% /
/dev/ida/c0d0p2 7278671 1792903 5108572 26% /usr
/dev/ida/c0d1p2 21879869 5527532 15209937 27% /data
/dev/ida/c0d1p1 21106623 360226 19644798 2% /home
Output of "df -i" command:
Filesystem Inodes IUsed IFree IUse% Mounted on
/dev/ida/c0d0p1 246720 21812 224908 9% /
/dev/ida/c0d0p2 1886208 83951 1802257 4% /usr
/dev/ida/c0d1p2 5713920 427 5713493 0% /data
/dev/ida/c0d1p1 5509120 10240 5498880 0% /home
/proc/interrupts
CPU0
0: 698592 XT-PIC timer
1: 2022 XT-PIC keyboard
2: 0 XT-PIC cascade
4: 38999 XT-PIC serial
5: 643942 XT-PIC PCA-200E-0
7: 2161857 XT-PIC ida0
8: 0 XT-PIC rtc
12: 2589 XT-PIC PS/2 Mouse
13: 1 XT-PIC fpu
14: 2 XT-PIC ide0
NMI: 0
LOC: 0
ERR: 0
/proc/stat
cpu 3471 0 704707 0
cpu0 3471 0 704707 0
page 1842705 48657
swap 18851 34138
intr 3609284 708178 2022 0 0 39542 653344 3 2166090 0 0 37513 0 2589 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
disk_io: (7,0):(1207,4800,0,0)
ctxt 3275798
btime 968676055
processes 1094
Last the output of the kernel boot infos "dmesg":
(See attached file: dmesg.txt)
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (AGP disabled) (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64 set
Region 0: Memory at <unassigned> (32-bit, prefetchable)
00:06.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 14)
Subsystem: Unknown device 0e11:7004
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 1000 [disabled]
Region 1: Memory at 28000000 (32-bit, non-prefetchable) [disabled]
Region 2: Memory at 28001000 (32-bit, non-prefetchable) [disabled]
00:06.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 14)
Subsystem: Unknown device 0e11:7004
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 0: I/O ports at 1400 [disabled]
Region 1: Memory at 28000100 (32-bit, non-prefetchable) [disabled]
Region 2: Memory at 28002000 (32-bit, non-prefetchable) [disabled]
00:07.0 Network controller: Compaq Computer Corporation ProLiant Integrated Netelligent 10/100 (rev 10)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set, cache line size 08
Interrupt: pin A routed to IRQ 3
Region 0: I/O ports at 2400
Region 1: Memory at c6bfeef0 (32-bit, non-prefetchable)
00:08.0 VGA compatible controller: ATI Technologies Inc 215IIC [Mach64 GT IIC] (rev 7a)
Subsystem: Unknown device 1002:4756
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 64 set, cache line size 08
Region 0: Memory at c5000000 (32-bit, prefetchable)
Region 1: I/O ports at 2000
Region 2: Memory at c6bff000 (32-bit, non-prefetchable)
Capabilities: [5c] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 System peripheral: Compaq Computer Corporation: Unknown device a0f0
Subsystem: Unknown device 110e:f3b0
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 1800
Region 1: Memory at c6bfef00 (32-bit, non-prefetchable)
00:0d.0 PCI bridge: IBM IBM27-82351 (rev 07)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 set, cache line size 08
Bus: primary=00, secondary=01, subordinate=01, sec-latency=248
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c6f00000-c6ffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:0f.0 ATM network controller: FORE Systems Inc PCA-200E
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 1 min, 1 max, 64 set, cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at c6c00000 (32-bit, non-prefetchable)
00:10.0 Network controller: Compaq Computer Corporation Netelligent 10/100 (rev 10)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 2410
Region 1: Memory at c6bfeee0 (32-bit, non-prefetchable)
00:14.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:14.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at f100
00:14.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at 1c00 [disabled]
00:14.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 Unknown mass storage controller: Compaq Computer Corporation Smart-2/P RAID Controller (rev 04)
Subsystem: Unknown device 0e11:4032
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set, cache line size 08
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at 3000
Region 1: Memory at c6ffff00 (32-bit, non-prefetchable)
n type 1
PCI: Probing PCI hardware
PCI: Device 00:00 not found by BIOS
PCI: Device 00:a0 not found by BIOS
PCI: Device 00:a1 not found by BIOS
PCI: Device 00:a2 not found by BIOS
PCI: Device 00:a3 not found by BIOS
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 65536 bind 65536)
NET4: Linux IPX 0.38 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
Initializing RT netlink socket
Starting kswapd v1.7
pty: 256 Unix98 ptys configured
loop: registered device at major 7
loop: enabling 8 loop devices
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: CD-224E, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X CD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Loading I2O Core - (c) Copyright 1999 Red Hat Software
Linux I2O PCI support (c) 1999 Red Hat Software.
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999, 2000 Red Hat Software.
I2O LAN OSM (C) 1999 University of Helsinki.
cpqarray: Device e11 has been found at 1 0
Compaq SMART2 Driver (v 2.4.0)
Found 1 controller(s)
cpqarray: Finding drives on ida0 (Smart Array 3200)
cpqarray ida/c0d0: blksz=512 nr_blks=17764320
cpqarray ida/c0d1: blksz=512 nr_blks=177822720
Partition check:
ida/c0d0: p1 p2 p3 p4
ida/c0d1: p1 p2
fore200e: FORE Systems 200E-series driver - version 0.2d
fore200e: device PCA-200E found at 0xc6c00000, IRQ 5
fore200e: device PCA-200E-0 self-test passed
fore200e: device PCA-200E-0 firmware started
fore200e: device PCA-200E-0 initialized
fore200e: device PCA-200E-0, rev. A, S/N: 48333, ESI: 00:20:48:04:bc:cd
fore200e: IRQ 5 reserved for device PCA-200E-0
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10c
Non-volatile memory driver v1.1
ThunderLAN driver v1.9
TLAN: eth0 irq=10, io=2410, Compaq Netelligent 10/100 TX PCI UTP, Rev. 16
TLAN: eth1 irq= 3, io=2400, Compaq Netelligent Integrated 10/100 TX UTP, Rev. 16
TLAN: 2 devices installed
kmem_create: Forcing size word alignment - nfs_fh
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 232k freed
Adding Swap: 318232k swap-space (priority -1)
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: RRIP_1991A
TLAN: eth0: Starting autonegotiation.
TLAN: eth0: Autonegotiation complete.
TLAN: eth0: Link active with AutoNegotiation enabled, at 10Mbps Half-Duplex
TLAN: Partner capability: 10BaseT-HD
bug: kernel timer added twice at c01b6808.
bug: kernel timer added twice at c01b6808.
bug: kernel timer added twice at c01b6808.
nfs warning: mount version older than kernel
atm_connect (TX: cl 1,bw 0-0,sdu 484; RX: cl 1,bw 0-0,sdu 484,AAL 5)
atmsvc: no signaling demon
atmsvc: no signaling demon
atm_connect (TX: cl 1,bw 0-0,sdu 1000; RX: cl 1,bw 0-0,sdu 1000,AAL 5)
lec.c: Sep 6 2000 19:00:04 initialized
lec0: Initialized!
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 0,bw 0-0,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 0,bw 0-0,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0-353207,sdu 1516; RX: cl 1,bw 0-353207,sdu 1516,AAL 5)
atm_connect (TX: cl 1,bw 0--1,sdu 1516; RX: cl 1,bw 0-0,sdu 1516,AAL 5)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Sep 15 2000 - 21:00:14 EST