Well, I've applied the IDE patches for 2.2.17, and everything
appears to be working with my VIA board much better now.
I'm not sure it is totally optimal yet though. My CDROM's are on
the second channel, and I don't much care about them.
Can I configure it somehow to optimize it for single channel
operation with 2 Quantum Fireballs? Leaving the second channel
UDMAless? I read something about tweaking FIFO, but don't have a
clue about it and don't want to risk anything.
Plus could y'all look at the data below and tell me if anything
is wrong or should be changed? I'm a bit worried about the hdd
failure warning/error messages on /dev/hdd (my 4x Toshiba CDROM).
I'm using: hdparm -X66 -m16c1d1k1
Also, if there is a linux-ide mailing list, where is it? I
couldn't find one on linux-ide.org nor on www.liszt.com...
Any help appreciated.
1 root@asdf:/proc# cat ide/via
Command register = 0x7
Master Read Cycle IRDY 1 Wait State
Master Write Cycle IRDY 1 Wait State
FIFO Output Data 1/2 Clock Advance: off
Bus Master IDE Status Register Read Retry: on
Latency timer = 32 (max. = 0)
Interrupt Steering Swap: off
------------------Primary IDE------------Secondary IDE-----
both channels togth: yes yes
Prefetch Buffer : on on
Post Write Buffer: on on
FIFO Conf/Chan. : 08 08
Threshold Prim. : 1/2 1/2
Read DMA FIFO flush: on on
End Sect. FIFO flush: on on
Max DRDY Pulse Width: No limitation
Bytes Per Sector: 512 512
--------------drive0------drive1-------drive0------drive1----
DMA enabled: yes yes yes no
Act Pls Width: 03 03 04 07
Recovery Time: 01 01 02 06
Add. Setup T.: 4T 4T 4T 4T
------------------UDMA-Timing-Control------------------------
Enable Meth.: 0 0 0 0
Enable: yes yes no no
Transfer Mode: PIO PIO DMA DMA
Cycle Time: 2T 2T 5T 5T
1 root@asdf:/proc# hdparm -v /dev/hd[abcd]
/dev/hda:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 1 (on)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 935/255/63, sectors = 15032115, start = 0
/dev/hdb:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 1 (on)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 524/255/63, sectors = 8418816, start = 0
/dev/hdc:
HDIO_GET_MULTCOUNT failed: Input/output error
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
HDIO_GET_NOWERR failed: Input/output error
readonly = 0 (off)
BLKRAGET failed: Input/output error
HDIO_GETGEO failed: Invalid argument
hdd: set_drive_speed_status: status=0x51 { DriveReady
SeekComplete Error }
hdd: set_drive_speed_status: error=0x04
hdd: ATAPI 4X CD-ROM drive, 256kB Cache
/dev/hdd:
HDIO_GET_MULTCOUNT failed: Invalid argument
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
HDIO_GET_NOWERR failed: Invalid argument
readonly = 1 (on)
readahead = 8 (on)
HDIO_GETGEO failed: Invalid argument
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VT 82C598 Apollo MVP3
Chipset Core ATA-33
Split FIFO Configuration: 8 Primary buffers, threshold = 1/2
8 Second. buffers, threshold = 1/2
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA,
hdb:DMA
ide0: VIA Bus-Master (U)DMA Timing Config Success
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA,
hdd:pio
ide1: VIA Bus-Master (U)DMA Timing Config Success
hda: QUANTUM FIREBALL EL7.6A, ATA DISK drive
hdb: QUANTUM FIREBALL SE4.3A, ATA DISK drive
hdc: HP CD-Writer+ 7200, ATAPI CDROM drive
hdd: TOSHIBA CD-ROM XM-5302TA, ATAPI CDROM drive
hdd: set_drive_speed_status: status=0x51 { DriveReady
SeekComplete Error }
hdd: set_drive_speed_status: error=0x04
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: QUANTUM FIREBALL EL7.6A, 7339MB w/418kB Cache,
CHS=935/255/63, UDMA(33)
hdb: QUANTUM FIREBALL SE4.3A, 4110MB w/80kB Cache,
CHS=524/255/63, UDMA(33)
----------------------------------------------------------------------
Mike A. Harris - Linux advocate - Open source advocate
Computer Consultant - Capslock Consulting
Copyright 2000 all rights reserved
----------------------------------------------------------------------
[Mike A. Harris Linux tip #1 - 50 line mode]
Is the 80x25 line screen too small for you? If you want more screen real
estate, you can set 50 column mode by editing your /etc/lilo.conf file, and
adding a new line with "vga=ext" to the global section near the top. Save
and exit, then run "lilo". Next time you boot, you'll have a nice big 80x50
screen.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sat Oct 07 2000 - 21:00:09 EST