I've been searching and watching lists for a while trying to figure
out whether this problem had been solved or not, and haven't found
anything suitable...
I'm experiencing two problems with a Promise UDMA66 controller
(PDC20262) on hardware I'll list below. The first problem is that
on bootup I get:
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100%% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
PDC20262: IDE controller on PCI bus 00 dev 60
PDC20262: chipset revision 1
PDC20262: not 100%% native mode: will probe irqs later
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI
Mode.
ide2: BM-DMA at 0x9800-0x9807, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x9808-0x980f, BIOS settings: hdg:pio, hdh:pio
hdc: NEC CD-ROM DRIVE:282, ATAPI CDROM drive
hde: Maxtor 91024U3, ATA DISK drive
hdf: Maxtor 94098U8, ATA DISK drive
hdg: QUANTUM FIREBALLP LM15, ATA DISK drive
hdh: QUANTUM FIREBALLP LM30, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xb000-0xb007,0xa802 on irq 11
ide3 at 0xa400-0xa407,0xa002 on irq 11
Then a hang. Mentioned a while back, this patch fixes the problem,
and allows the machine to boot properly.
--- /usr/src/linux-2.2.18-idepatch/drivers/block/ide-features.c Mon
Jan 1 18:03:42 2001
+++ ide-features.c Mon Jan 1 18:30:37 2001
@@ -297,8 +297,10 @@
SELECT_DRIVE(HWIF(drive), drive);
SELECT_MASK(HWIF(drive), drive, 0);
udelay(1);
+ /*
if (IDE_CONTROL_REG)
OUT_BYTE(drive->ctl | 2, IDE_CONTROL_REG);
+ */
OUT_BYTE(speed, IDE_NSECTOR_REG);
OUT_BYTE(SETFEATURES_XFER, IDE_FEATURE_REG);
OUT_BYTE(WIN_SETFEATURES, IDE_COMMAND_REG);
I then found that I randomly get "Timeout waiting for DMA" messages
prior to a complete system hang.
I tried forcing all of the drives into UDMA mode 2 (hdparm -X66) and
this seemed to make the problem a bit better, but I still experience
system hangs. I can't seem to make the problem happen, it only
happens randomly. The past two times, an rsync has made the system crash.
I'm using kernel 2.2.18 (tried 2.4 final briefly today to see if it
would boot, it hung on bootup as well), with the latest
ide.2.2.18.1221.patch from Andre's directory.
The system in question is:
Celeron 533 - 384 MB RAM - Asus P2B-F
4 IDE Drives listed above:
hde: Maxtor 91024U3, ATA DISK drive
hdf: Maxtor 94098U8, ATA DISK drive
hdg: QUANTUM FIREBALLP LM15, ATA DISK drive
hdh: QUANTUM FIREBALLP LM30, ATA DISK drive
1 IDE CDROM:
hdc: NEC CD-ROM DRIVE:282, ATAPI CDROM drive
Promise Ultra66 Controller, BIOS 2.0b18
2 D-Link DFE-538 (RTL8139) adapters
Any help, or any way I could help would be appreciated. Eager to try
and get this resolved, as I've seen it crop up a number of times, and
it's also a pain to have to physically hit the reset button as the
machine is off-site.
-- Adrian - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Jan 07 2001 - 21:00:23 EST