Hello,
Since this looks like either a chipset, drive, or driver problem, I am
submitting this.
I have recently started using DMA mode on my harddisk. However, I
occasionally (not often/constant, but sometimes) get CRC errors:
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
After reading some archives in linux-kernel, I tried changing some
options. Then I changed out the 40 pin, 80 wire cable with a new one.
The errors still occasionally happened, so I then checked out the
included floppy disk with the drive and used the utilities and saw that
it was set for a maximum capability of ATA/100, so i changed it to
ATA/66, but no change in results. I've since changed it back to ATA/100
capabilities. Running without DMA mode never gives any errors what so
ever. Running with DMA mode gives me over 30 more MB/sec, so I would
really like to use it...
My main concern that I havnt beem able to find an answer for on any
archives or documentation, Can this cause file system corruption in any way?
The hardware is a VP_IDE: VIA vt82c686a IDE UDMA66 (VIA KT133 chipset on
an Abit KT7 board)
The drive is a Western Digital Caviare 7200rpm 40gig hard drive.
I have support for my chipset compiled in as well
Kernel: 2.4.0
[root@Earth root]$ hdparm -i /dev/hda
/dev/hda:
Model=WDC WD400BB-00AUA1, FwRev=18.20D18, SerialNo=WD-WMA6R2018028
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
[root@Earth root]# hdparm -I /dev/hda
/dev/hda:
Model=DW CDW04B0-B00UA1A , FwRev=812.D081,
SerialNo=DWW-AMR6028120
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
[root@Earth root]# hdparm /dev/hda
/dev/hda:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 4865/255/63, sectors = 78165360, start = 0
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
VP_IDE: VIA vt82c686a IDE UDMA66 controller on pci0:7.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:pio
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=38166/64/32, UDMA(66)
If any other information is needed, I will be more than happy to supply
it. Any help/information will be greatly appreciated.
Thank you.
-- James Brents James@nistix.com- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Mon Jan 15 2001 - 21:00:30 EST