Hi,
I am not subscribed to this list. Please email me with any
questions.
I've been trying unsuccessfully to use 2.4 kernels for a while
now. I wanted to use DRI and it seems I need a 2.4 kernel for it to work
but I have the following problem:
description:
when I go to pretty much any directory, but for example, /usr/src
(/usr is mounted as /dev/hdc5) and do an "ls", the list starts but it
freezes at a certain entry and as far as I can tell never resumes. I can
press control-c and it aborts just fine and my computer keeps running
normally - I can do pretty much anything - but if I try to list the file
(the one it stopped at) or many others, the same thing happens again. I
can't think of anything remarkable about /dev/hd5 - it is an ext2
partition, on an IBM Ultra33 drive (see below), on the motherboard
controller. Perhaps it is because I have an Intel 840 chipset
motherboard? Oh, DMA is on, block transfer is on and 32 bit transfer is on
for this drive. Here is my hardware:
Intel 840 chipset (SuperMicro P3DME) with two 850MHz Pentium 3 chips
(100MHz bus, slot1), 512MB PC100RAM (2x256MB buffered ECC; ECC disabled).
Voodoo3 3500 AGP TV, Promise Ultra66, SoundBlaster Live! MP3+, Adaptec
AIC-7850 SCSI card with Plextor 8x CD burner and Pioneer 10x DVD drive,
Znyx ZX348Q (two DEC Tulip chips with a PCI bus controller).
The motherboard has onboard LAN (EtherExpressPro 100) and sound (don't
know what; it's disabled).
Hard drives are layed out as follows:
hda: LS-120 VER5 00 UHD Floppy, ATAPI FLOPPY drive
hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
hdc: IBM-DJNA-352500, ATA DISK drive
hde: IBM-DPTA-353750, ATA DISK drive
hdg: IBM-DPTA-353750, ATA DISK drive
hde and hdg are on the Promise Ultra66 controller and are part of a stripe
set using normal kernel RAID support. However I have this problem on
drives not associated with this stripe set.
here is how hdc is partitioned:
Disk /dev/hdc: 16 heads, 63 sectors, 49585 cylinders
Units = cylinders of 1008 * 512 bytes
Device Boot Start End Blocks Id System
/dev/hdc1 1 66 33232+ 83 Linux
/dev/hdc2 67 587 262584 82 Linux swap
/dev/hdc3 * 588 4749 2097648 83 Linux
/dev/hdc4 4750 49585 22597344 5 Extended
/dev/hdc5 4750 10991 3145936+ 83 Linux
/dev/hdc6 10992 49585 19451344+ 83 Linux
and how they are mounted:
/dev/hdc2 swap swap defaults 0 0
/dev/hde5 swap swap defaults 0 0
/dev/hdg5 swap swap defaults 0 0
/dev/hdc3 / ext2 defaults,nocheck,noatime 1 1
/dev/hdc5 /usr ext2 defaults,nocheck,noatime 1 2
/dev/hdc6 /home ext2 defaults,nocheck,noatime 1 3
/dev/hdc1 /boot ext2 defaults,nocheck,noatime 1 4
/dev/md0 /raid ext2 defaults,nocheck,noatime 1 2
here are my SCSI drives incase it helps:
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<Adaptec AIC-7850 SCSI host adapter>
scsi : 1 host.
(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: PIONEER Model: DVD-ROM DVD-305 Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
(scsi0:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 8.
Vendor: IMATION Model: CD-RW IMW080220 Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 4, lun 0
scsi : detected 2 SCSI generics 2 SCSI cdroms total.
sr0: scsi3-mmc drive: 16x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.11
sr1: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
I don't think I have anything strange in my kernel config but if you
want I can send it to you - or anything else you need to fix this - even
access to my machine in this state if you want.
I hope this helps.
Nicholas
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sat Mar 31 2001 - 21:00:24 EST