I confirm similar problems (see my message from yesterday).
AIC7XXX_OLD also failed for me. I have tried aic 6.1.8 as well
as 6.1.10.
Both 2.4.0 under redhat 7.0 and 2.4.1 as shipped by redhat
wolverine work. As have all earlier versions going back to 2.3.xx
and 2.2.x
On Mon, Apr 09, 2001 at 03:33:47PM -0500, Jim Studt wrote:
> > > A typical startup with 6.1.9 proceeds like this... (6.1.10 hangs silently
> > > after emitting the scsi0 and scsi1 adapter summaries, maybe it is
> > > going through the same gyrations silently.)
> > >
> >
>
> Alan Cox directs...
> > Try saying N to the AIC7xxx driver and Y to AIC7XXX_OLD and see if that works.
> > This is important both because it might solve your problem for now but also
> > because if the old driver works we can be fairly sure the bug is in the
> > new adaptec driver and not elsewhere and triggered on it
>
> Using AIC7XXX_OLD does not work either. Different output....
>
> SCSI subsystem driver Revision: 1.00
> PCI: Assigned IRQ 11 for device 00:0c.0
> PCI: The same IRQ used for device 00:0c.1
> PCI: Found IRQ 11 for device 00:0c.1
> PCI: The same IRQ used for device 00:0c.0
> (scsi0) <Adaptec AIC-7896/7 Ultra2 SCSI host adapter> found at PCI 0/12/0
> (scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
> (scsi0) Downloading sequencer code... 392 instructions downloaded
> (scsi1) <Adaptec AIC-7896/7 Ultra2 SCSI host adapter> found at PCI 0/12/1
> (scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
> (scsi1) Downloading sequencer code... 392 instructions downloaded
> scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
> <Adaptec AIC-7896/7 Ultra2 SCSI host adapter>
> scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
> <Adaptec AIC-7896/7 Ultra2 SCSI host adapter>
> scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Inquiry 00 00 00 ff 00
> SCSI host 0 abort (pid 0) timed out - resetting
> SCSI bus is being reset for host 0 channel 0.
> SCSI host 0 channel 0 reset (pid 0) timed out - trying harder
> SCSI bus is being reset for host 0 channel 0.
> SCSI host 0 abort (pid 0) timed out - resetting
> SCSI bus is being reset for host 0 channel 0.
> SCSI host 0 channel 0 reset (pid 0) timed out - trying harder
> SCSI bus is being reset for host 0 channel 0.
> SCSI host 0 abort (pid 0) timed out - resetting
> SCSI bus is being reset for host 0 channel 0.
> ...
>
>
> Since we are looking elsewhere now... I have tried PCI access mode
> BIOS and Direct with no improvement.
>
> There is an unrecognized PCI bridge resource in the boot messages...
>
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 256K
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU serial number disabled.
> CPU: Intel Pentium III (Coppermine) stepping 06
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.37 (20001109) Richard Gooch (rgooch@atnf.csiro.au)
> mtrr: detected mtrr type: Intel
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Unknown bridge resource 0: assuming transparent
> Unknown bridge resource 1: assuming transparent
> Unknown bridge resource 2: assuming transparent
> Unknown bridge resource 0: assuming transparent
> Unknown bridge resource 1: assuming transparent
> Unknown bridge resource 2: assuming transparent
> PCI: Discovered primary peer bus ff [IRQ]
> PCI: Using IRQ router PIIX [8086/7110] at 00:12.0
>
> # lspci
> 00:00.0 Host bridge: Intel Corporation 440GX - 82443GX Host bridge
> 00:01.0 PCI bridge: Intel Corporation 440GX - 82443GX AGP bridge
> 00:0c.0 SCSI storage controller: Adaptec 7896
> 00:0c.1 SCSI storage controller: Adaptec 7896
> 00:0e.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)
> 00:12.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
> 00:12.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
> 00:12.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
> 00:12.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
> 00:14.0 VGA compatible controller: Cirrus Logic GD 5480 (rev 23)
> 01:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21150 (rev 06)
>
> I will go back and try 2.4.0 and 2.4.3-ac3 and see where that gets me.
>
> --
> Jim Studt, President
> The Federated Software Group, Inc.
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Apr 15 2001 - 21:00:12 EST