Hi,
I have a machine running a 2.4.2 kernel with an Adaptec SCSI
board. This worked well, but when I ran into a hang with the 2.4.2
loop device, testing a CD image, I decided to switch to 2.4.3. But
then I get strange error messages during boot, and the machine reacts
(kind of once a day) in a very strange way, like programs failing
which never fail. Might those errors have lead to a subtile kind of
file system corruption? Inspite of the `request_module' message below,
I compiled the driver into the kernel and do not use any disk related
kernel modules. And of course, at a so early stage, the root file
system was not yet mounted.
Below are the SCSI related lines from the boot messages, first with
2.4.3, and 3 minutes later back with the previous 2.4.2
kernel. Andybody how could tell me what to do? Please CC me as I'm not
on this list. Thanks in advance.
---------------------------------------------------------------------------
Linux version 2.4.3
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
PCI: Found IRQ 11 for device 00:0f.0
The same IRQ used for device 00:11.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.5
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Wide Channel A, SCSI Id=7, 32/255 SCBs
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 8195
scsi0:0:0:0: Attempting to queue a TARGET RESET message
aic7xxx_dev_reset returns 8195
Recovery SCB completes
scsi: device set offline - not ready or command retry failed after bus reset: host 0 channel 0 id 0 lun 0
Vendor: QUANTUM Model: ATLAS_V_18_WLS Rev: 0230
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 2, lun 0
(scsi0:A:2): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
Vendor: HP Model: CD-Writer+ 9200 Rev: 1.0e
Type: CD-ROM ANSI SCSI revision: 04
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
(scsi0:A:6): 10.000MB/s transfers (10.000MHz, offset 15)
scsi0:0:2:0: Tagged Queuing enabled. Depth 8
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
SCSI device sda: 35861388 512-byte hdwr sectors (18361 MB)
/dev/scsi/host0/bus0/target2/lun0: p1 p2 p3
---------------------------------------------------------------------------
Linux version 2.4.2
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 11 for device 00:0f.0
PCI: The same IRQ used for device 00:11.0
(scsi0) <Adaptec AIC-7892 Ultra 160/m SCSI host adapter> found at PCI 0/15/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 392 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
<Adaptec AIC-7892 Ultra 160/m SCSI host adapter>
(scsi0:0:2:0) Synchronous at 80.0 Mbyte/sec, offset 63.
Vendor: QUANTUM Model: ATLAS_V_18_WLS Rev: 0230
Type: Direct-Access ANSI SCSI revision: 03
(scsi0:0:6:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: HP Model: CD-Writer+ 9200 Rev: 1.0e
Type: CD-ROM ANSI SCSI revision: 04
Detected scsi disk sda at scsi0, channel 0, id 2, lun 0
SCSI device sda: 35861388 512-byte hdwr sectors (18361 MB)
/dev/scsi/host0/bus0/target2/lun0: p1 p2 p3
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
-- Christoph Simon datageo@terra.com.br --- ^X^C q quit :q ^C end x exit ZZ ^D ? help shit . - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Apr 15 2001 - 21:00:13 EST