this is my problem
i have a 3c595TX card and when i plus it in my hub it at 10base T i
tride to put the new modules and nothing changed i have a 2.2.16 kernel
and 2.4.1 kenel and it's the same in the too cases ,
and i have to other computer using a 100base T cards from real tek and
they appear at 100 base T in the hub and te rate of any fule transfert
is up to 10 mb/s between the to other computer , so is there any
upgrade to do for the bios of the nic card or is it normal " i don't
think so but why not "
sorry for my poor english i try to do my best
00:0a.0 Ethernet controller: 3Com Corporation 3c595 100BaseTX [Vortex]
Flags: bus master, medium devsel, latency 248, IRQ 18
I/O ports at e800 [size=32]
Expansion ROM at eb000000 [disabled] [size=64K]
00: b7 10 50 59 07 00 00 02 00 00 00 02 00 f8 00 00
10: 01 e8 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 eb 00 00 00 00 00 00 00 00 05 01 03 08
100 base T hubed
vortex-diag.c:v2.04 1/8/2001 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Index #1: Found a 3Com 3c595 Vortex 10/100baseTx adapter at 0xe800.
The Vortex chip may be active, so FIFO registers will not be read.
To see all register values use the '-f' flag.
Initial window 7, registers values by window:
Window 0: 0000 0000 0000 0000 0000 00bf 0000 0000.
Window 1: FIFO FIFO 0000 2000 8000 00ff 3ffc 2000.
Window 2: a000 8a24 1c66 0000 0000 0000 00de 4000.
Window 3: 001b 0001 0000 0020 e10a bfff 3fff 6000.
Window 4: 0000 00d4 0000 0c80 0001 88c0 0000 8000.
Window 5: 1ffc 1ffc 00de 1ffc 0007 02de 00de a000.
Window 6: 0000 0000 0000 3000 0000 4e5b 2bb7 c000.
Window 7: 0000 0000 0000 0000 8000 00ff 0000 e000.
Vortex chip registers at 0xe800
0xE810: **FIFO** 00000000 00008000 *STATUS*
0xE820: ffffffff ffffffff ffffffff ffffffff
0xE830: ffffffff ffffffff ffffffff ffffffff
Indication enable is 00de, interrupt enable is 02de.
No interrupt sources are pending.
Transceiver/media interfaces available: 100baseTx 10baseT.
Transceiver type in use: 10baseT.
MAC settings: full-duplex.
Maximum packet size is 0.
Station address set to 00:a0:24:8a:66:1c.
Configuration options 00de.
EEPROM contents (64 words, offset 0):
0x000: 00a0 248a 661c 5950 c095 0036 5542 6d50
0x008: 0418 0000 00a0 248a 661c bf20 0000 0000
0x010: 11c6 0000 001b 0001 0000 0000 0000 000e
0x018: 0000 0000 0000 0000 0000 0000 0000 0000
0x020: 0000 0000 0000 0000 0000 0000 0000 0000
0x028: 0000 0000 0000 0000 0000 0000 0000 0000
0x030: 0000 0000 0000 0000 0000 0000 0000 0000
0x038: 0000 0000 0000 0000 0000 0000 0000 0000
The word-wide EEPROM checksum is 0xc861.
Parsing the EEPROM of a 3Com Vortex/Boomerang:
3Com Node Address 00:A0:24:8A:66:1C (used as a unique ID only).
OEM Station address 00:A0:24:8A:66:1C (used as the ethernet address).
Manufacture date (MM/DD/YYYY) 4/21/1996, division 6, product BU.
Options: force full-duplex.
Vortex format checksum is correct (000e vs. 000e).
Cyclone format checksum is correct (00 vs. 00).
Hurricane format checksum is correct (00 vs. 00).
eth0 Link encap:Ethernet HWaddr 00:A0:24:8A:66:1C
inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9656 errors:200 dropped:200 overruns:0 frame:311
TX packets:9779 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:5767681 (5.5 Mb) TX bytes:1539404 (1.4 Mb)
Interrupt:18 Base address:0xe800
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Mon Apr 23 2001 - 21:00:24 EST