aic7xxx errors with 2.4.8-ac7 on 440gx mobo

From: Yusuf Goolamabbas (yusufg@outblaze.com)
Date: Mon Aug 20 2001 - 03:36:30 EST

Next message: Rogério Brito: "Problems with 2.2.19 but not with 2.2.18 (was: Re: [OOPS] Oopsen with 2.2.19)"
Previous message: Alexander Griesser: "Re: Kernel 2.4.9, esssolo soundcard, NTFS support"
Next in thread: Cliff Albert: "Re: aic7xxx errors with 2.4.8-ac7 on 440gx mobo"
Reply: Cliff Albert: "Re: aic7xxx errors with 2.4.8-ac7 on 440gx mobo"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi, 2.4.8 and 2.4.9 have no problems compiling and booting on a P3 500
440GX mobo (APIC not compiled in the kernel)

With 2.4.8-ac7, I get SCSI errors and the kernel fails to boot. If I
compile with APIC enabled and APIC on UP also enabled, it boots
cleanly

booting with append="noapic", gives the same errors

SCSI subsystem driver Revision: 1.00
PCI: Assigned IRQ 11 for device 00:0c.0
PCI: Sharing IRQ 11 with 00:0c.1
PCI: Found IRQ 11 for device 00:0c.1
PCI: Sharing IRQ 11 with 00:0c.0

scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
<Adaptec aic7896/97 Ultra2 SCSI adapter>
aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs

scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
<Adaptec aic7896/97 Ultra2 SCSI adapter>
aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/255 SCBs

scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command already completed
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 8195
scsi0:0:0:0: Attempting to queue a TARGET RESET message
aic7xxx_dev_reset returns 8195
Recovery SCB completes
scsi0:0:0:0: Attempting to queue an ABORT message
ahc_intr: HOST_MSG_LOOP bad phase 0x0
scsi0:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 8194
scsi: device set offline - not ready or command retry failed after bus reset: host 0 channel 0 id 0 lun 0
scsi0:0:1:0: Attempting to queue an ABORT message
scsi0:0:1:0: Command already completed
aic7xxx_abort returns 8194
scsi0:0:1:0: Attempting to queue an ABORT message
scsi0:0:1:0: Command already completed
aic7xxx_abort returns 8194
scsi0:0:1:0: Attempting to queue a TARGET RESET message
scsi0:0:1:0: Is not an active device
scsi0:0:1:0: Attempting to queue an ABORT message
scsi0:0:1:0: Command already completed
aic7xxx_abort returns 8194

Regards, Yusuf
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Rogério Brito: "Problems with 2.2.19 but not with 2.2.18 (was: Re: [OOPS] Oopsen with 2.2.19)"
Previous message: Alexander Griesser: "Re: Kernel 2.4.9, esssolo soundcard, NTFS support"
Next in thread: Cliff Albert: "Re: aic7xxx errors with 2.4.8-ac7 on 440gx mobo"
Reply: Cliff Albert: "Re: aic7xxx errors with 2.4.8-ac7 on 440gx mobo"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

This archive was generated by hypermail 2b29 : Thu Aug 23 2001 - 21:00:34 EST