Rene Rebe writes:
> On Thu, 29 Nov 2001 17:34:11 -0700
> Richard Gooch <rgooch@ras.ucalgary.ca> wrote:
> > Um, from your previous message, it seems that host numbering doesn't
> > change depending on BIOS settings.
>
> It was the first storry - my older Athlon.
OK, so, just to be clear, BIOS settings are *not* changing host
numbering. IOW, "host1" always refers to the same piece of hardware,
whether or not "host1" appears in devfs.
> > So what exactly is happening? And what is the problem? I realise you
> > may find the naming a little confusing, but is there an actual
> > problem?
>
> ok - again.
>
> I have a K6 on an ALI Aladin-5 board and an additional IDE controller
> (Promisse). The onboard can be found as /dev/host0 and the additional
> Promisse one appears as /dev/host2:
>
> server1:~ # l /dev/ide/
> total 0
> drwxr-xr-x 1 root root 0 Jan 1 1970 .
> drwxr-xr-x 1 root root 0 Jan 1 1970 ..
> drwxr-xr-x 1 root root 0 Jan 1 1970 host0
> drwxr-xr-x 1 root root 0 Jan 1 1970 host2
>
> The boot messages:
[...]
> I works - but sucks, because I'm not able to predict the
> ide-controller entries in /dev/ide/* because they seem (for me)
> randomly on each workstaion I am ...
But it is actually predictable, isn't it? Think of it this way: the
IDE subsystem reserves "slots" (host numbers) for installed hardware.
If a piece of hardware is disabled in the BIOS, it doesn't mean that
the slot won't be reserved.
> (All info from my very first mail ...)
>
> The other bug is: On a Athlon-600 workstation based on an Irongate
> board (Asus-K7M) I have to disable the first (primarry) channel of
> the onbaord IDE controller, because it has problem with the UDMA-66
> mode. But when I disable this channel, Linux generates a /dev/ide/host1
> entry - No host0 entry is there. Sure it works - but sucks, too!
> (Generates a very unstable feeling in me ...)
The "host0" entry isn't shown, because it is disabled. But to say
"when I disable this channel, Linux generates a /dev/ide/host1" isn't
correct, and implies a problem where there isn't. The correct way to
describe this is:
"host0" is my primary onboard IDE controller. It might not appear if I
disable it.
"host1" is my secondary onboard IDE controller. It has the same name
whether or not I disable the primary.
And this is a Feature[tm]. It means that tomorrow when a shiny new
drive arrives, you can plug it into your primary channel and enable
the channel in the BIOS. You can then boot without having to fix your
/etc/fstab, because /dev/ide/host1 is still pointing to the same
devices.
The only thing that confuses me is why the secondary onboard channel
is /dev/ide/host1 rather than /dev/ide/host0/bus1.
Regards,
Richard....
Permanent: rgooch@atnf.csiro.au
Current: rgooch@ras.ucalgary.ca
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Nov 30 2001 - 21:00:36 EST