I'm back to trying to get my laptop working with both it's cardbus
slots again....
I tried the latest 2.4.18-pre7 + mppe(VPN) + Jes Sorenson's
IRQ routing patch for certain VAIOS. Jes' patch was recently
posted to LKML, but it does not seem to affect my problem...
However, the same problems I was having with the 2.4.6 kernel
a while back are still here. When I insert an adapter in the
second cardbus slot, the machine hangs (alt-sysrq-p does nothing)
I see this when I remove the NIC, and the machine starts working again.
cs: socket c7f90000 timed out during reset. Try increasing setup_delay.
I believe the problem lies with this:
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Assigned IRQ 9 for device 00:0a.0
PCI: Assigned IRQ 10 for device 00:0a.1
IRQ routing conflict for 00:07.5, have irq 5, want irq 10
IRQ routing conflict for 00:07.6, have irq 5, want irq 10
PCI: Sharing IRQ 10 with 00:10.0
If I can offer any more debugging information, don't hesitate
to ask!
The full dump of lspci -vv, and dmesg is attached. dump_pirq.pl
shows this:
[root@lanforge-ice log]# dump_pirq.pl
Interrupt routing table found at address 0xfdf60:
Version 1.0, size 0x0080
Interrupt router is device 00:07.0
PCI exclusive interrupt mask: 0x0000 []
Compatible router: vendor 0x1106 device 0x0596
Device 00:07.0 (slot 0): ISA bridge
INTA: link 0x55, irq mask 0x9eb8 [3,4,5,7,9,10,11,12,15]
INTB: link 0x56, irq mask 0x9eb8 [3,4,5,7,9,10,11,12,15]
INTC: link 0x56, irq mask 0x9cb8 [3,4,5,7,10,11,12,15]
INTD: link 0x57, irq mask 0x06a0 [5,7,9,10]
Device 00:00.0 (slot 0): Host bridge
INTA: link 0x55, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15]
INTB: link 0x56, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15]
INTC: link 0x56, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15]
INTD: link 0x57, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15]
Device 00:01.0 (slot 0): PCI bridge
INTA: link 0x56, irq mask 0x0020 [5]
Device 00:0a.0 (slot 0): CardBus bridge
INTA: link 0x55, irq mask 0x0020 [5]
INTB: link 0x56, irq mask 0x0020 [5]
Device 00:10.0 (slot 0): Ethernet controller
INTA: link 0x56, irq mask 0x0400 [10]
Device 00:0e.0 (slot 0): FireWire (IEEE 1394)
INTA: link 0x57, irq mask 0x0200 [9]
Interrupt router at 00:07.0: VIA 82C686 PCI-to-ISA bridge
PIRQA (link 0x01): irq 9
PIRQB (link 0x02): irq 10
PIRQC (link 0x03): irq 5
PIRQD (link 0x05): irq 9
[root@lanforge-ice log]#
Thanks,
Ben
-- Ben Greear <greearb@candelatech.com> <Ben_Greear AT excite.com> President of Candela Technologies Inc http://www.candelatech.com ScryMUD: http://scry.wanfear.com http://scry.wanfear.com/~greear
Linux version 2.4.18-pre7 (greear@lanforge-ice) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #3 Sat Feb 2 07:26:56 MST 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ea400 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable) BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data) BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS) BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved) On node 0 totalpages: 32752 zone(0): 4096 pages. zone(1): 28656 pages. zone(2): 0 pages. Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Kernel command line: ro root=/dev/hda5 Initializing CPU#0 Detected 800.048 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1595.80 BogoMIPS Memory: 126348k/131008k available (1275k kernel code, 4272k reserved, 341k data, 256k init, 0k highmem) Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes) Inode-cache hash table entries: 8192 (order: 4, 65536 bytes) Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) CPU: Before vendor init, caps: 0183fbff c1c7fbff 00000000, vendor = 2 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 64K (64 bytes/line) CPU: After vendor init, caps: 0183fbff c1c7fbff 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000 CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000 CPU: AMD Duron(tm) Processor stepping 01 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 800.0754 MHz. ..... host bus clock speed is 200.0187 MHz. cpu: 0, clocks: 2000187, slice: 1000093 CPU0<T0:2000176,T1:1000080,D:3,S:1000093,C:2000187> mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xfd83d, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware Trying to stomp on VIA Northbridge bug... Unknown bridge resource 2: assuming transparent PCI: Using IRQ router VIA [1106/0686] at 00:07.0 PCI: Cannot allocate resource region 4 of device 00:07.3 PCI: Disabling Via external APIC routing isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Sony Vaio laptop detected. Starting kswapd VFS: Diskquotas version dquot_6.4.0 initialized pty: 2048 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A Real Time Clock Driver v1.10e block: 128 slots per queue, batch=32 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 39 VP_IDE: chipset revision 16 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1 ide0: BM-DMA at 0x1c00-0x1c07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1c08-0x1c0f, BIOS settings: hdc:DMA, hdd:pio hda: FUJITSU MHM2100AT, ATA DISK drive hdc: HITACHI DVD-ROM GD-S200, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 19640880 sectors (10056 MB) w/2048KiB Cache, CHS=1222/255/63, UDMA(66) ide-floppy driver 0.97.sv Partition check: hda: hda1 hda2 < hda5 hda6 > Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 ide-floppy driver 0.97.sv Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] PCI: Assigned IRQ 9 for device 00:0a.0 PCI: Assigned IRQ 10 for device 00:0a.1 IRQ routing conflict for 00:07.5, have irq 5, want irq 10 IRQ routing conflict for 00:07.6, have irq 5, want irq 10 PCI: Sharing IRQ 10 with 00:10.0 Intel PCIC probe: not found. Databook TCIC-2 PCMCIA probe: not found. md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 Yenta IRQ list 0808, PCI irq9 Socket status: 30000020 Yenta IRQ list 0808, PCI irq10 Socket status: 30000006 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 8192 bind 8192) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. cs: cb_alloc(bus 2): vendor 0x10b7, device 0x5157 PCI: Enabling device 02:00.0 (0000 -> 0003) VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 256k freed Adding Swap: 265032k swap-space (priority -1) usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.268 $ time 17:30:35 Feb 1 2002 usb-uhci.c: High bandwidth mode enabled PCI: Enabling device 00:07.2 (0000 -> 0001) PCI: Assigned IRQ 9 for device 00:07.2 PCI: Sharing IRQ 9 with 00:07.3 PCI: Sharing IRQ 9 with 00:0e.0 usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Enabling device 00:07.3 (0000 -> 0001) PCI: Found IRQ 9 for device 00:07.3 PCI: Sharing IRQ 9 with 00:07.2 PCI: Sharing IRQ 9 with 00:0e.0 usb-uhci.c: USB UHCI at I/O 0x1c20, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.268:USB Universal Host Controller Interface driver
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03) Subsystem: Sony Corporation: Unknown device 803d Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 8 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b115 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: f4100000-f5ffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22) Subsystem: Sony Corporation: Unknown device 803d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 4: I/O ports at 1c00 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 22 Interrupt: pin D routed to IRQ 9 Region 4: I/O ports at fce0 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 22 Interrupt: pin D routed to IRQ 9 Region 4: I/O ports at 1c20 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 9 Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 20) Subsystem: Sony Corporation: Unknown device 80e3 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at 1000 [size=256] Region 1: I/O ports at 1c14 [size=4] Region 2: I/O ports at 1c10 [size=4] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.6 Communication controller: VIA Technologies, Inc. AC97 Modem Controller (rev 20) Subsystem: Sony Corporation: Unknown device 80e3 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at 1400 [size=256] Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 CardBus bridge: Texas Instruments PCI1420 Subsystem: Sony Corporation: Unknown device 80e3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 10400000-107ff000 (prefetchable) Memory window 1: 10800000-10bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+ 16-bit legacy interface ports at 0001
00:0a.1 CardBus bridge: Texas Instruments PCI1420 Subsystem: Sony Corporation: Unknown device 80e3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin B routed to IRQ 10 Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=06, subordinate=09, sec-latency=176 Memory window 0: 10c00000-10fff000 (prefetchable) Memory window 1: 11000000-113ff000 I/O window 0: 00004800-000048ff I/O window 1: 00004c00-00004cff Secondary status: SERR BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001
00:0e.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020 (prog-if 10 [OHCI]) Subsystem: Sony Corporation: Unknown device 80e3 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 9 Region 0: Memory at f4004000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 1 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10) Subsystem: Sony Corporation: Unknown device 80e3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 1800 [size=256] Region 1: Memory at f4004800 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA]) Subsystem: Sony Corporation: Unknown device 80e3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 5 Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at 9000 [size=256] Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [50] AGP version 1.0 Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> Capabilities: [5c] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Ethernet controller: 3Com Corporation 3CCFE575BT Cyclone CardBus (rev 01) Subsystem: 3Com Corporation 3C575 Megahertz 10/100 LAN Cardbus PC Card Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2500ns min, 1250ns max) Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at 4000 [size=128] Region 1: Memory at 10800000 (32-bit, non-prefetchable) [size=128] Region 2: Memory at 10800080 (32-bit, non-prefetchable) [size=128] Expansion ROM at 10400000 [size=128K] Capabilities: [50] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu Feb 07 2002 - 21:00:23 EST