- Just removaing dead obscure xlate_1024 code.
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/drivers/ide/cs5530.c linux/drivers/ide/cs5530.c
--- linux-2.5.30/drivers/ide/cs5530.c 2002-08-03 15:03:26.000000000 +0200
+++ linux/drivers/ide/cs5530.c 2002-08-02 02:24:32.000000000 +0200
@@ -204,8 +204,6 @@ static unsigned int __init pci_init_cs55
{
struct pci_dev *master_0 = NULL;
struct pci_dev *cs5530_0 = NULL;
- unsigned short pcicmd = 0;
- unsigned long flags;
pci_for_each_dev(dev) {
if (dev->vendor == PCI_VENDOR_ID_CYRIX) {
@@ -233,7 +231,7 @@ static unsigned int __init pci_init_cs55
* Enable BusMaster and MemoryWriteAndInvalidate for the cs5530:
* --> OR 0x14 into 16-bit PCI COMMAND reg of function 0 of the cs5530
*/
-
+
pci_set_master(cs5530_0);
pci_set_mwi(cs5530_0);
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/drivers/ide/ide.c linux/drivers/ide/ide.c
--- linux-2.5.30/drivers/ide/ide.c 2002-08-03 15:03:26.000000000 +0200
+++ linux/drivers/ide/ide.c 2002-08-02 10:58:52.000000000 +0200
@@ -251,7 +251,7 @@ static struct ata_bit_messages ata_statu
static struct ata_bit_messages ata_error_msgs[] = {
{ ICRC_ERR|ABRT_ERR, ABRT_ERR, "drive status error" },
- { ICRC_ERR|ABRT_ERR, ICRC_ERR, "bad sectorr" },
+ { ICRC_ERR|ABRT_ERR, ICRC_ERR, "bad sector" },
{ ICRC_ERR|ABRT_ERR, ICRC_ERR|ABRT_ERR, "invalid checksum" },
{ ECC_ERR, ECC_ERR, "uncorrectable error" },
{ ID_ERR, ID_ERR, "sector id not found" },
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/drivers/ide/Makefile linux/drivers/ide/Makefile
--- linux-2.5.30/drivers/ide/Makefile 2002-08-03 15:03:26.000000000 +0200
+++ linux/drivers/ide/Makefile 2002-08-02 02:28:01.000000000 +0200
@@ -1,15 +1,12 @@
#
-# Makefile for the kernel ata, atapi, and ide block device drivers.
+# Makefile for the kernel ata and atapi block device drivers.
#
-# 12 September 2000, Bartlomiej Zolnierkiewicz <bkz@linux-ide.org>
+# 12 September 2000, Bartłomiej Żołnierkiewicz <bkz@linux-ide.org>
# Rewritten to use lists instead of if-statements.
#
-# Note : at this point, these files are compiled on all systems.
-# In the future, some of these should be built conditionally.
-#
-export-objs := device.o ide-taskfile.o main.o ide.o probe.o quirks.o pcidma.o tcq.o \
- atapi.o ataraid.o
+export-objs := device.o ide-taskfile.o main.o ide.o probe.o quirks.o \
+ pcidma.o tcq.o atapi.o ataraid.o
obj-$(CONFIG_BLK_DEV_HD) += hd.o
obj-$(CONFIG_BLK_DEV_IDE) += ide-mod.o
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/drivers/ide/probe.c linux/drivers/ide/probe.c
--- linux-2.5.30/drivers/ide/probe.c 2002-08-03 15:03:26.000000000 +0200
+++ linux/drivers/ide/probe.c 2002-08-02 02:20:34.000000000 +0200
@@ -41,115 +41,6 @@
extern struct ata_device * get_info_ptr(kdev_t);
/*
- * This is called from the partition-table code in pt/msdos.c
- * to invent a translated geometry.
- *
- * This is suppressed if the user specifies an explicit geometry.
- *
- * The ptheads parameter is either 0 or tells about the number of
- * heads shown by the end of the first nonempty partition.
- * If this is either 16, 32, 64, 128, 240 or 255 we'll believe it.
- *
- * The xparm parameter has the following meaning:
- * 0 = convert to CHS with fewer than 1024 cyls
- * using the same method as Ontrack DiskManager.
- * 1 = same as "0", plus offset everything by 63 sectors.
- * -1 = similar to "0", plus redirect sector 0 to sector 1.
- * 2 = convert to a CHS geometry with "ptheads" heads.
- *
- * Returns 0 if the translation was not possible, if the device was not
- * an IDE disk drive, or if a geometry was "forced" on the commandline.
- * Returns 1 if the geometry translation was successful.
- */
-int ide_xlate_1024(kdev_t i_rdev, int xparm, int ptheads, const char *msg)
-{
- struct ata_device *drive;
- const char *msg1 = "";
- int heads = 0;
- int c, h, s;
- int transl = 1; /* try translation */
- int ret = 0;
-
- drive = get_info_ptr(i_rdev);
- if (!drive)
- return 0;
-
- /* There used to be code here that assigned drive->id->CHS to
- * drive->CHS and that to drive->bios_CHS. However, some disks have
- * id->C/H/S = 4092/16/63 but are larger than 2.1 GB. In such cases
- * that code was wrong. Moreover, there seems to be no reason to do
- * any of these things.
- *
- * Please note that recent RedHat changes to the disk utils are bogous
- * and will report spurious errors.
- */
-
- /* translate? */
- if (drive->forced_geom)
- transl = 0;
-
- /* does ptheads look reasonable? */
- if (ptheads == 32 || ptheads == 64 || ptheads == 128 ||
- ptheads == 240 || ptheads == 255)
- heads = ptheads;
-
- if (xparm == 2) {
- if (!heads ||
- (drive->bios_head >= heads && drive->bios_sect == 63))
- transl = 0;
- }
- if (xparm == -1) {
- if (drive->bios_head > 16)
- transl = 0; /* we already have a translation */
- }
-
- if (transl) {
- static const u8 dm_head_vals[] = {4, 8, 16, 32, 64, 128, 255, 0};
- const u8 *headp = dm_head_vals;
- unsigned long total;
-
- /*
- * If heads is nonzero: find a translation with this many heads
- * and S=63. Otherwise: find out how OnTrack Disk Manager
- * would translate the disk.
- *
- * The specs say: take geometry as obtained from Identify,
- * compute total capacity C*H*S from that, and truncate to
- * 1024*255*63. Now take S=63, H the first in the sequence 4,
- * 8, 16, 32, 64, 128, 255 such that 63*H*1024 >= total.
- * [Please tell aeb@cwi.nl in case this computes a geometry
- * different from what OnTrack uses.]
- */
-
- total = ata_capacity(drive);
-
- s = 63;
-
- if (heads) {
- h = heads;
- c = total / (63 * heads);
- } else {
- while (63 * headp[0] * 1024 < total && headp[1] != 0)
- headp++;
- h = headp[0];
- c = total / (63 * headp[0]);
- }
-
- drive->bios_cyl = c;
- drive->bios_head = h;
- drive->bios_sect = s;
- ret = 1;
- }
-
- drive->part[0].nr_sects = ata_capacity(drive);
-
- if (ret)
- printk("%s%s [%d/%d/%d]", msg, msg1,
- drive->bios_cyl, drive->bios_head, drive->bios_sect);
- return ret;
-}
-
-/*
* Drive ID data come as little endian, it needs to be converted on big endian
* machines.
*/
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/drivers/ide/qd65xx.c linux/drivers/ide/qd65xx.c
--- linux-2.5.30/drivers/ide/qd65xx.c 2002-08-03 15:03:26.000000000 +0200
+++ linux/drivers/ide/qd65xx.c 2002-08-02 02:37:07.000000000 +0200
@@ -103,7 +103,7 @@ static void qd_select(struct ata_device
* upper nibble represents recovery time, in count of VLB clocks
*/
-static u8 qd6500_compute_timing(struct ata_channel *hwif, int active_time, int recovery_time)
+static u8 qd6500_compute_timing(struct ata_channel *ch, int active_time, int recovery_time)
{
u8 active_cycle,recovery_cycle;
@@ -172,15 +172,15 @@ static int qd_timing_ok(struct ata_devic
static void qd_set_timing(struct ata_device *drive, u8 timing)
{
- struct ata_channel *hwif = drive->channel;
+ struct ata_channel *ch = drive->channel;
drive->drive_data &= 0xff00;
drive->drive_data |= timing;
- if (qd_timing_ok(hwif->drives)) {
+ if (qd_timing_ok(ch->drives)) {
qd_select(drive); /* selects once */
- hwif->selectproc = NULL;
+ ch->selectproc = NULL;
} else
- hwif->selectproc = &qd_select;
+ ch->selectproc = &qd_select;
printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
}
@@ -279,61 +279,64 @@ static int __init qd_testreg(int port)
}
/*
- * called to setup an ata channel : adjusts attributes & links for tuning
+ * Adjusts attributes & links for tuning.
*/
-void __init qd_setup(int unit, int base, int config, unsigned int data0, unsigned int data1, void (*tuneproc) (struct ata_device *, u8 pio))
+static void __init qd_setup(int unit, int base, int config, unsigned int data0, unsigned int data1, void (*tuneproc) (struct ata_device *, u8 pio))
{
- struct ata_channel *hwif = &ide_hwifs[unit];
+ struct ata_channel *ch = &ide_hwifs[unit];
- hwif->chipset = ide_qd65xx;
- hwif->unit = unit;
- hwif->select_data = base;
- hwif->config_data = config;
- hwif->drives[0].drive_data = data0;
- hwif->drives[1].drive_data = data1;
- hwif->io_32bit = 1;
- hwif->tuneproc = tuneproc;
+ ch->chipset = ide_qd65xx;
+ ch->unit = unit;
+ ch->select_data = base;
+ ch->config_data = config;
+ ch->drives[0].drive_data = data0;
+ ch->drives[1].drive_data = data1;
+ ch->io_32bit = 1;
+ ch->tuneproc = tuneproc;
}
+#ifdef MODULE
/*
- * called to unsetup an ata channel : back to default values, unlinks tuning
+ * Called to unsetup an ata channel : back to default values, unlinks tuning.
*/
-void __init qd_unsetup(int unit) {
- struct ata_channel *hwif = &ide_hwifs[unit];
- u8 config = hwif->config_data;
- int base = hwif->select_data;
- void *tuneproc = (void *) hwif->tuneproc;
+static void __init qd_unsetup(int unit) {
+ struct ata_channel *ch = &ide_hwifs[unit];
+ u8 config = ch->config_data;
+ int base = ch->select_data;
+ void *tuneproc = (void *) ch->tuneproc;
- if (!(hwif->chipset == ide_qd65xx)) return;
+ if (ch->chipset != ide_qd65xx)
+ return;
- printk(KERN_NOTICE "%s: back to defaults\n", hwif->name);
+ printk(KERN_NOTICE "%s: back to defaults\n", ch->name);
- hwif->selectproc = NULL;
- hwif->tuneproc = NULL;
+ ch->selectproc = NULL;
+ ch->tuneproc = NULL;
if (tuneproc == (void *) qd6500_tune_drive) {
// will do it for both
- outb(QD6500_DEF_DATA, QD_TIMREG(&hwif->drives[0]));
+ outb(QD6500_DEF_DATA, QD_TIMREG(&ch->drives[0]));
} else if (tuneproc == (void *) qd6580_tune_drive) {
- if (QD_CONTROL(hwif) & QD_CONTR_SEC_DISABLED) {
- outb(QD6580_DEF_DATA, QD_TIMREG(&hwif->drives[0]));
- outb(QD6580_DEF_DATA2, QD_TIMREG(&hwif->drives[1]));
+ if (QD_CONTROL(ch) & QD_CONTR_SEC_DISABLED) {
+ outb(QD6580_DEF_DATA, QD_TIMREG(&ch->drives[0]));
+ outb(QD6580_DEF_DATA2, QD_TIMREG(&ch->drives[1]));
} else {
- outb(unit ? QD6580_DEF_DATA2 : QD6580_DEF_DATA, QD_TIMREG(&hwif->drives[0]));
+ outb(unit ? QD6580_DEF_DATA2 : QD6580_DEF_DATA, QD_TIMREG(&ch->drives[0]));
}
} else {
printk(KERN_WARNING "Unknown qd65xx tuning fonction !\n");
printk(KERN_WARNING "keeping settings !\n");
}
}
+#endif
/*
- * looks at the specified baseport, and if qd found, registers & initialises it
- * return 1 if another qd may be probed
+ * Looks at the specified baseport, and if qd found, registers & initialises it
+ * return 1 if another qd may be probed.
*/
-int __init qd_probe(int base)
+static int __init qd_probe(int base)
{
u8 config;
int unit;
@@ -397,13 +400,10 @@ int __init qd_probe(int base)
}
#ifndef MODULE
-/*
- * called by ide.c when parsing command line
- */
-
void __init init_qd65xx(void)
{
- if (qd_probe(0x30)) qd_probe(0xb0);
+ if (qd_probe(0x30))
+ qd_probe(0xb0);
}
#else
@@ -414,8 +414,12 @@ MODULE_LICENSE("GPL");
int __init qd65xx_mod_init(void)
{
- if (qd_probe(0x30)) qd_probe(0xb0);
- if (ide_hwifs[0].chipset != ide_qd65xx && ide_hwifs[1].chipset != ide_qd65xx) return -ENODEV;
+ if (qd_probe(0x30))
+ qd_probe(0xb0);
+ if (ide_hwifs[0].chipset != ide_qd65xx
+ && ide_hwifs[1].chipset != ide_qd65xx)
+ return -ENODEV;
+
return 0;
}
module_init(qd65xx_mod_init);
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/fs/partitions/Makefile linux/fs/partitions/Makefile
--- linux-2.5.30/fs/partitions/Makefile 2002-08-03 15:03:26.000000000 +0200
+++ linux/fs/partitions/Makefile 2002-08-02 02:22:20.000000000 +0200
@@ -2,7 +2,7 @@
# Makefile for the linux kernel.
#
-export-objs := check.o msdos.o
+export-objs := check.o
obj-y := check.o
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/fs/partitions/msdos.c linux/fs/partitions/msdos.c
--- linux-2.5.30/fs/partitions/msdos.c 2002-08-03 15:03:26.000000000 +0200
+++ linux/fs/partitions/msdos.c 2002-08-02 02:22:25.000000000 +0200
@@ -22,17 +22,6 @@
#include <linux/config.h>
#include <linux/buffer_head.h> /* for invalidate_bdev() */
-#ifdef CONFIG_BLK_DEV_IDE
-#include <linux/hdreg.h>
-#include <linux/ide.h> /* IDE xlate */
-#elif defined(CONFIG_BLK_DEV_IDE_MODULE)
-#include <linux/module.h>
-
-int (*ide_xlate_1024_hook)(kdev_t, int, int, const char *);
-EXPORT_SYMBOL(ide_xlate_1024_hook);
-#define ide_xlate_1024 ide_xlate_1024_hook
-#endif
-
#include "check.h"
#include "msdos.h"
#include "efi.h"
diff -durNp -X /tmp/diff.uRHk8V linux-2.5.30/include/linux/ide.h linux/include/linux/ide.h
--- linux-2.5.30/include/linux/ide.h 2002-08-03 15:03:26.000000000 +0200
+++ linux/include/linux/ide.h 2002-08-02 02:21:00.000000000 +0200
@@ -1091,12 +1091,6 @@ extern ide_startstop_t ata_error(struct
extern void ide_fixstring(char *s, const int bytecount, const int byteswap);
/*
- * This routine is called from the partition-table code in genhd.c
- * to "convert" a drive to a logical geometry with fewer than 1024 cyls.
- */
-int ide_xlate_1024(kdev_t, int, int, const char *);
-
-/*
* Convert kdev_t structure into struct ata_device * one.
*/
struct ata_device *get_info_ptr(kdev_t i_rdev);
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Wed Aug 07 2002 - 22:00:30 EST