The new aic7xxx driver hangs on boot with the following messages. Once
the card is hung, only a cold boot will restore it to a sane state
(causes problems in older kernels too).
Boot log:
---------
PCI: Found IRQ 10 for device 00:0b.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.26
<Adaptec aic7850 SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
(scsi0:A:1:0): refuses WIDE negotiation. Using 8bit transfers
scsi0:0:1:0: Attempting to queue an ABORT message
scsi0: Dumping Card State in Data-in phase, at SEQADDR 0x7b
ACCUM = 0xfc, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
HCNT = 0x20 SCBPTR = 0x0
ERROR[0x0] SCSIPHASE[0x0] SCSIBUSL[0x20] LASTPHASE[0x40]:(IOI)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) SBLKCTL[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0x20]:(DPHASE) SSTAT0[0x0] SSTAT1[0x3]:(REQINIT|PHASECHG)
SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x0]
SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x78]:(HDMAEN|SDMAEN|SCSIEN|WIDEODD)
DFSTATUS[0x0]
STACK: 0x0 0x0 0x1b4 0x6e
SCB count = 4
Kernel NEXTQSCB = 2
Card NEXTQSCB = 2
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2
Sequencer SCB Info:
0 SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x17] SCB_LUN[0x0]
SCB_TAG[0x3]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(LID) SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(LID) SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x17] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(1): 3
DevQ(0:1:0): 0 waiting
scsi0:0:1:0: Device is active, asserting ATN
Recovery code sleeping
Good Boot log:
--------------
PCI: Found IRQ 10 for device 00:0b.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
<Adaptec aic7850 SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
(scsi0:A:1): 10.000MB/s transfers (10.000MHz, offset 15)
Vendor: TOSHIBA Model: CD-ROM XM-6201TA Rev: 1030
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:3): 10.000MB/s transfers (10.000MHz, offset 15)
Vendor: YAMAHA Model: CRW6416S Rev: 1.0c
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:4:0): refuses synchronous negotiation. Using asynchronous transfers
Vendor: IOMEGA Model: ZIP 100 Rev: E.11
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 4, lun 0
sda : MODE SENSE failed.
sda : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sense key Illegal Request
Additional sense: Invalid field in cdb
sda : assuming drive cache: write through
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 3, lun 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 16x/16x writer cd/rw xa/form2 cdda tray
lscpi output:
-------------
00:0b.0 SCSI storage controller: Adaptec AHA-7850 (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 9800 [disabled] [size=256]
Region 1: Memory at d5800000 (32-bit, non-prefetchable) [size=4K]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Wed Jan 15 2003 - 22:00:40 EST